® High Performance Indoor/Outdoor Color CCTV Dome Camera User Manual Products: BLK-CCD203VS, BLK-CCD205VH, BLK-CPD206VH, BLK-CCD223VS, BLK-CCD225VH, BLK-CPD226VH Please read this manual before using your camera, and always follow the instructions for safety and proper use. Save this manual for future reference.
! WARNING CAUTION Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. To prevent electric shock and risk of fire hazards: Use a power source that is within specification only. Do NOT expose this appliance to rain or moisture. REGULATORY NOTICE This device complies with Part 15 of the FCC Rules.
Table of Contents Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv SECTION 1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Cameras with a vandalproof enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.
Precautions Do not install the camera in extreme temperature conditions. Use the camera in environments where temperature is between 14°F and 122°F. Use adequate ventilation in high temperature. Do not install or use the camera in an environment where the humidity is high. It can cause the image quality to be poor. Do not install the camera under unstable lighting conditions. Severe lighting changes or flicker can cause the camera to work improperly. Never use the camera close to a gas or oil leak.
SECTION 1: INTRODUCTION SECTION 1 Introduction SC Black high performance indoor/outdoor CCTV dome cameras feature a very high resolution Sony® CCD sensor providing 600 TVL, with a 2.8 – 11mm lens, a digital wide dynamic range, dual voltage range support (24 VAC, 12 VDC), and on-screen display (OSD) for control and setup. These cameras are available with or without an IR array, and in either a durable plastic or vandalproof enclosure. 1.1 Cameras with a vandalproof enclosure 1.1.
SECTION 1: INTRODUCTION Camera with vandalproof enclosure Camera with IR array and vandalproof enclosure 1.1.2 What’s in the box Your camera includes the following: • • • • • • • 2 Security tool Machine screws (4) Mounting cap Mounting screws (4) L-wrench User manual Dome bracket (optional) www.sc-black.
SECTION 1: INTRODUCTION What’s in the box Optional dome bracket for wall and ceiling mounting 1.1.
SECTION 1: INTRODUCTION 1.2 Cameras with a plastic enclosure 1.2.1 • • • • • • • • • • • • • • • Features Wall or ceiling mounting through 3-axis camera bracket Safety strap keeps dome cover attached while making adjustments 1/3” Sony Super HAD CCD II: 410K pixels High resolution 600 TV Lines Day or day/night (ICR) operation Vari-focal lens 2.
SECTION 1: INTRODUCTION Camera with IR array and plastic enclosure 1.2.
SECTION 2: INSTALLATION SECTION 2 Installation 2.1 General Guidelines • Outdoor installations: Use the rubber rings included with the machine screws (4) to ensure that the unit is sealed properly. • Dome/window care: Handle the dome carefully to prevent scratching. If a scratch appears over the lens, adjust the dome window to move the scratch out of view. CAUTION Keep dome cover and camera lens clean.
SECTION 2: INSTALLATION Power Connector 2.1.1 Video Coax Connector What you need To install the camera you will need: • • 12 VDC or 24 VAC power source Tools for mounting the camera 2.2 Vandalproof camera mounting The camera can be installed on a junction box or directly to a wall or ceiling. 1. Attach the surface mount bracket to the ceiling or wall using four (4) mounting screws. 2. Connect the dome base to the surface mount bracket using the screws with rubber rings provided. 3.
SECTION 2: INSTALLATION 2.3 Plastic camera mounting 1. Connect the dome base to the mounting surface using four (4) screws. 2. Route the power and video cables to the camera location and attach them to the camera drop cable (see General guidelines above). 2.4 Camera adjustments 1. Attach a video setup monitor to the yellow RCA (EXTRA VIDEO OUT) connector inside the camera assembly, or setup a remote monitor for viewing video from the camera. 2. Power on the camera and video monitor. 3.
SECTION 2: INSTALLATION Ceiling mounting Wall mounting 4. Adjust the image with the focus and zoom levers. 5. Configure your camera using the software menus in the OSD. See Software Setup in the following section of this manual. 6. Place the dome cover over the base and adjust the dome window. Tighten the captive screws that secure the cover to the base. 7. Clean the camera dome with an approved glass cleaning solution and a lint free cloth.
SECTION 3: SOFTWARE SETUP SECTION 3 Software Setup Use the SETUP joy stick on the OSD control panel to navigate through the menu system. Press the joy stick down (toward the camera) to enter the SETUP menu or select an entry, rock the stick up or down to highlight an item in the list, and left or right display the option you want to select. The SETUP menu consists of a list of sub-menus or displays the option selected for a camera function. When sub-menus are available, the symbol is shown. 3.
SECTION 3: SOFTWARE SETUP DWDR: The DWDR feature employs intelligent light level control to compensate for strong backlight conditions. DWDR: OFF / ON DWDR OFF DWDR ON 3.3 WHITE BALANCE WHITE BAL: You can select one of the following modes: ATW1 / ATW2 / AWC g SET / MANUAL (INDOOR / OUTDOOR / MANUAL) —— —— —— —— —— —— ATW1: Automatically adjusts color according to the available lighting for temperature range: 2500°K to 9500°K.
SECTION 3: SOFTWARE SETUP —— —— RED GAIN: Adjust R gain value 0 ~ 255 BLUE GAIN: Adjust B gain value 0 ~ 255 3.4 BACKLIGHT BACKLIGHT: Select OFF / BLC / HLC BLC (Back Light Compensation) —— —— —— —— —— —— —— AREA SEL: Select AREA1, AREA2 AREA STATE: Select OFF / ON GAIN: Select 0 ~ 255 steps HEIGHT: Select 0 ~ 15 steps WIDTH: Select 0 ~ 15 steps LEFT/RIGHT: Select 0 ~ 15 steps TOP/BOTTOM: Select 0 ~ 15 steps HLC (High Light Compensation) —— 12 LEVEL: Select 0 ~ 255 steps www.sc-black.
SECTION 3: SOFTWARE SETUP —— MODE: ALL DAY, NIGHT ONLY 3.5 DAY&NIGHT DAY&NIGHT: Select AUTO / COLOR / B/W / EXT · AUTO: Day&Night Auto mode —— —— —— —— D -> N LEVEL: 182 ~ 192 steps D -> N DELAY: 1 ~ 30 SEC N -> D LEVEL: 0 ~ 10 steps N -> D DELAY: 1 ~ 30 SEC COLOR: Day&Night only color mode B/W: Day&Night black and white (B/W) mode —— —— BURST: OFF / ON IR SMART: OFF / ON. This option controls the IR LED output level to compensate for object distance.
SECTION 3: SOFTWARE SETUP IR SMART OFF IR SMART ON R GAIN: 0 ~ 255 HEIGHT: 0 ~ 15 WIDTH: 0 ~ 15 LEFT/RIGHT: 0 ~ 15 TOP/BOTTOM: 0 ~ 15 —— IR LEVEL: HIGH / LOW EXT: Day&Night EXT mode 3.6 DPC (Dead Pixel Compensation) Select DPC for dead pixel compensation processing. DPC can be set to OFF (default) or AUTO. When AUTO is used, the camera will remove defective pixels from an image automatically. 14 www.sc-black.
SECTION 3: SOFTWARE SETUP 3.7 SPECIAL CAM TITLE: Select camera title menu (Text edit). MOTION: Select camera title menu (Text edit) —— —— —— —— —— —— —— —— AREA SEL: Select AREA1, AREA2, AREA3, AREA4 AREA STATE: Select OFF / ON HEIGHT: Select 0 ~ 15 steps WIDTH: Select 0 ~ 15 steps LEFT/RIGHT: Select 0 ~ 15 steps TOP/BOTTOM: Select 0 ~ 15 steps DEGREE: Select 0 ~ 255 steps VIEW: OFF / ON PRIVACY: You can cover an area of the screen.
SECTION 3: SOFTWARE SETUP —— —— —— —— WIDTH: Select 0 ~ 255 steps LEFT/RIGHT: Select 0 ~ 255 steps TOP/BOTTOM: Select 0 ~ 255 steps COLOR: Select 0 ~ 15 steps PARK.LINE: You can insert a line on the screen. This feature may be useful when aligning the camera image with objects in the field of view. —— —— —— —— —— —— —— LT: You can adjust the top left area on screen. (0 ~ 195 steps) LB: You can adjust the bottom left area on screen. (0 ~ 194 steps) RT: You can adjust the top right area on screen.
SECTION 3: SOFTWARE SETUP MIRROR OFF —— —— —— —— —— MIRROR ON FONT COLOR: FONT: 16 colors (O ~ 15 steps) ID & TITLE: O ~ 15 steps CONTRAST: You can adjust contrast on screen. (0 ~ 255 steps) SHARPNESS: You can adjust camera image for clarity. (0 ~ 31 steps) DISPLAY: You can adjust camera output for the display type. (CRT / LCD / USER) CRT (Cathode Ray Tube, Braun tube). PED LEVEL: 0 ~ 63 steps, COLOR GAIN: 0 ~ 255 steps LCD (Liquid Crystal Display) GAMMA: 0.05 ~ 1.
SECTION 3: SOFTWARE SETUP —— —— —— —— —— CAM ID: Select the camera ID. 1 ~ 255 BAUD RATE: Select serial communication speed: 2400 / 4800 / 9600 / 19200 / 38400 / 57600 bps PROTOCOL: Select operating protocol. PELCO-D / PELCO-P DISPLAY ID: Select display item. OFF/ON ID POS: You can adjust ID position on screen. LANGUAGE: You can select language. ENGLISH / CHINESE VERSION: Factory vision. RESET: Set the camera options to the factory default settings. 18 www.sc-black.
SECTION 4: SPECIFICATIONS SECTION 4 Specifications Table 1. Model Differences Indoor Outdoor TDN IR BLK-CCD203VS BLK-CCD223VS -- -- BLK-CCD205VH BLK-CCD225VH √ -- BLK-CPD206VH BLK-CPD226VH √ √ TDN: True Day & Night, uses an IR cut filter instead of switching the image to black and white. IR: Built-in infrared LED array Table 2.
SECTION 4: SPECIFICATIONS Component Value Day&Night Auto / Color / BW / Ext Auto Level / Delay selectable BW Burst off/on / IR Smart off/on (Gain/level selectable) DPC Dead Pixels Compensation Special Title / MD / PM / Parking / Image / Comm / Language / Version Cam Title Text edit Motion Off / On (4 position) Privacy Off / On (8 position) Park.
APPENDIX A: TROUBLESHOOTING APPENDIX A Troubleshooting Problem Solution Nothing appears on the screen. - Check the power connections. - Check the video cable connections. - Ensure that the lens mode is set to DC (VIDEO). The video image is not clear. - Clean the lens with a soft, clean cloth. - Adjust the monitor screen for room lighting conditions. - Move the camera if necessary. The screen is dark. - Adjust the contrast feature of the monitor.
APPENDIX B: CAMERA DIMENSIONS APPENDIX B Camera Dimensions All dimensions shown below are in millimeters. 2.95" 1.61" 1.38" 4.96" Camera with vandalproof housing 2.95" 1.81" 1.52" 1.75" 2.09" Camera with plastic housing 3.29" 22 www.sc-black.
