BLK-HDPTZ12 2 Megapixel 12x HD-SDI / HDcctv PTZ Dome Camera User Manual Product: BLK-HDPTZ12 Please read this manual before using your camera, and always follow the instructions for safety and proper use. Save this manual for future reference.
REGULATORY NOTICE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Table of Contents SECTION 1 SECTION 2 SECTION 3 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 What’s in the box . . . . . . . . . . . .
TABLE OF CONTENTS SECTION 4 SECTION 5 APPENDIX A APPENDIX B APPENDIX C iv 3.6 DOME MOTION SETUP menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 3.6.1 GENERAL SETUP menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 3.6.2 MOTION SETUP menu . . . .
PRECAUTIONS AND IMPORTANT SAFETY INSTRUCTIONS Precautions • Any changes or modifications to this camera which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the camera. • A regulated 24 Vac 2.5 A power supply is recommended for use with this camera for best picture and the stable operation. An unregulated power supply can cause damage to the camera. Any use of an unregulated power supply will void the product warranty.
NOTES vi
SECTION 1: INTRODUCTION SECTION 1 Introduction These high definition indoor/outdoor PTZ (pan / tilt / zoom) dome camera feature a 1/3” CMOS 2.1 megapixel sensor that provides full HD quality 1080p @ 30 fps.
SECTION 1: INTRODUCTION Mounting bracket Camera module cable loop Camera module retention screw Cable access Conduit port Camera Dome Assembly Camera module Camera inside dome A 2 foot camera module drop cable is routed into the mounting bracket and attached to trunk cables there. Trunk cables for HD-SDI video, composite video, power, alarms and RS-485 can be routed either through conduit connected to the conduit port, or in through the base of the mounting bracket. 1.
SECTION 1: INTRODUCTION In the diagram above, video output from each camera on the network is applied to a distribution box (J-box), then connected to a multiplexer, DVR/VCR, and monitor. The PTZ features of the cameras are controlled across an RS-485 network with a PTZ controller. Up to 99 BLK-HDPTZ12 cameras can be attached to a single RS-485 network. 1.2.
SECTION 2: INSTALLATION SECTION 2 Installation 2.1 General Guidelines • • • • • The camera drop cable connects to the network cables (RS-485, alarm in/out, HD-SDI video out, 24 Vac power leads) inside the mounting bracket provided with the camera. A cable access cover on the underside of the mounting bracket allows access to cable connections, and to the composite video monitoring drop.
SECTION 2: INSTALLATION 2. Drill holes in the mounting surface for the wall anchors (if used) or mounting bolts. —— If the network cables will be routed into the mounting bracket where it attaches to the wall, drill an appropriate hole for the network cables. 3. Attach the mounting bracket securely to the mounting surface using appropriate mounting hardware. 4. If conduit will be used to shield the network cables, install the conduit and attached it to the mounting bracket. 5.
SECTION 2: INSTALLATION SW301 SW302 SW303 PTZ camera Camera hardware switches (looking into the camera with dome removed) SW301, SW302 switches The SW301 and SW302 rotary switches are used to set the camera ID number in hexadecimal notation as follows: —— —— SW301: set to the left digit of the two-digit device ID in hexadecimal. SW302: Set to the right digit of the two-digit device ID in hexadecimal. In the example above, SW301 is set to “0” and SW302 is set to “1”.
SECTION 2: INSTALLATION Table 1.
SECTION 2: INSTALLATION SW303 switch The SW303 block switch contains 5 on/off switches. These switches are used as follows: —— Switch 1 (video mode): »» ON: CVBS is NTSC »» OFF: CVBS is PAL —— Switch 2 (RS-485 protocol) »» ON: Pelco P / D »» OFF: Pelco P/ Others —— Switches 3 and 4 are used together to set the RS-485 baud rate as shown in the table below. Switch 3 —— 4.
SECTION 2: INSTALLATION Safety cable clip loop Lock screw Safety cable clip 2. When inserting the top of the camera module into the mounting bracket, align the pointer on the camera module with the safety cable clip loop as shown below, then rotate the camera module until it is fully seated. Safety cable clip loop Alignment mark 3. Tighten the lock screw.
SECTION 2: INSTALLATION 4. Clip the safety cable to the loop on the mounting bracket. 5. Connect the network RS-485, alarm in/out, and HD-SDI cables to the camera drop cable. The alarm in/out terminal block pin definitions are shown on the label attached to the drop cable. The camera drop cable diagram is shown below.
SECTION 2: INSTALLATION CAUTION Do not use benzene, thinner or other chemical products on the camera assembly; these may dissolve the paint and promote damage of the surfaces. Before using any chemical product, read the accompanying instructions carefully. 9. Apply power to the 24 Vac network power leads to power on the camera. 10. Connect the recorder end of the HD-SDI cable to a video monitor and verify that video from the camera can be seen there. 11.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE SECTION 3 Software Setup - Operating Guide 3.1 Getting Started Install and connect the dome to an interface device before using this operating guide. Once installed, apply power to the dome and the start-up screen is displayed on the monitor. Before installing and operating the dome camera, please read this user’s manual carefully. This dome camera can be operated using two methods: • • 12 Use hot keys [Refer to Appendix]. Use OSD Menu on the monitor.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 3.1.1 Accessing the MAIN MENU [95] + [Preset] / [Menu] When you use Pelco-D and Pelco-P protocol with your controller, you can access to the MAIN MENU by pressing the key [95] + [Preset], or by pressing and holding the [MENU] key for 2 seconds. 3.1.2 Editing TITLE The title edit menu can be used in the setup for Preset/Pattern/Tour/Scan commonly. • • • • • Move the joystick right in MAIN MENU.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 3.2 MAIN MENU To navigate within the menu system: • • • • • p /q: move joystick up and down for selecting an item. t / u : move joystick left and right for moving an item. u/ [OPEN]/ [NEAR]: move joystick right to select or save values or go to edit pages. u/ [CLOSE]/ [FAR]: move joystick to cancel or to exit current menu. BACK : to previous menu without saving. 3.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 3.3.1 INFO – System Information The system Information displays model name, version, Protocol, Communication Type, and camera ID (IDxxx). This is a read-only display. The camera ID reflects the ID switching setting. To display the System Information screen follow the steps below. 1. Open the MAIN MENU. 2. Select SYSTEM using the joystick [u]. 3. Move the joystick right [u] for selecting {Info} in the sub menu of {System}. 4.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 2. Select SYSTEM using the joystick [u], then move to REBOOT. 3. To reboot the system, press the NEAR key. To cancel the reboot, press the FAR key. 3.3.3 INITIALIZE menu Use this function to initialize all or specific parameters of dome to factory default parameters. 1. Open the MAIN MENU. 2. Select SYSTEM using the joystick [u], then move to INITIALIZE. 3. Select items to be initialized.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 3.3.4 Entering a PASSWORD To prevent unauthorized changes to the dome settings, the dome have the feature of password protection. An unauthorized operator cannot access to any of the dome settings menus. The password must be entered before programming. The valid password with four characters must be entered to continue programming. 1. Open the MAIN MENU. 2. Select SYSTEM using the joystick [u], then move to PASSWORD using the joystick [u]. 3.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE To navigate within the menu system: • • • • p/q: move joystick up and down for selecting an item. t/u: move joystick left and right for moving an item. u/ [OPEN]/ [NEAR]: move joystick right to select or save values or go to edit pages. u/ [CLOSE]/ [FAR]: move joystick to cancel or to exit current menu (back) 3.4.1 LANGUAGE menu To select a different OSD language: 1. Open the DISPLAY SETUP menu. 2. Rock the joystick up or down [p/q] to select LANGUAGE. 3.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 5. Move the joystick right [u] to change the status of labels. - Other labels can be set with same method. 6. Press the FAR key to return the previous menu (OSD SETUP). 7. Press the OPEN key or use joystick to save the status. 8. Press the CLOSE key or use joystick to return to previous menu (back). 3.4.3 PRIVACY ZONE SETUP menu A Private mask zone allows an administrator to configure one four-sided zone which cannot be viewed by operators.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 7. Press the OPEN key or use joystick to save settings. 8. Press the CLOSE key or use joystick to return to previous menu (back). 3.4.4 IMAGE SETUP menu Use the IMAGE SETUP menu to change the display image settings. 1. Open the MAIN MENU. 2. Select DISPLAY using the joystick [u], then select IMAGE SETUP. 3. Using joystick [u], select NORMAL image, HORIZONTAL image, VERTICAL image or H/V image. 4. Press the OPEN key or use joystick to save settings.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE The camera can monitor the movement of image, then send an alarm message with OSD and produce an Alarm Out condition. The sensitivity for movement can be changed to avoid false reporting. NOTE To temporarily stop alarm (about 10 s), press [ESC] key or [96+preset]. 1. Set MD/FD for Off/MD/FD using the joystick. 2. Set ALARM mode to OSD / ALARM OUT / BOTH using the joystick. 3. Press the OPEN key or use joystick to save settings. 4.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 3.5 CAMERA SETUP menu To navigate within the menu system: • • • • p/q: move joystick up and down for selecting an item. t/u: move joystick left and right for moving an item. u/ [OPEN]/ [NEAR]: move joystick right to select or save values or go to edit pages. u/ [CLOSE]/ [FAR]: move joystick to cancel or to exit current menu (back). 3.5.1 FOCUS/ZOOM SETUP Auto focus allows the lens to remain in focus during zoom-in, zoom-out and motion functions automatically.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE To use the FOCUS/ZOOM SETUP menu: 1. Open the MAIN MENU. 2. Select CAMERA SETUP using the joystick [u], then move to FOCUS/ZOOM using the joystick. 3. Set FOCUS mode to AUTO, MANUAL, or SEMI-AUTO. 4. Set the ZOOM SPD speed to SLOW or NORMAL, if preferred. 5. Set D.ZOOM to ON or OFF. 6. Using joystick [u], select NORMAL image, HORIZONTAL image, VERTICAL image or H/V image. 7. Press the OPEN key or use joystick to save settings. 8.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE To use the WB SETUP menu: 1. Open the MAIN MENU. 2. Select CAMERA SETUP using the joystick [u], then move to WB SETUP using the joystick. 3. Set the WB mode to AWT, INDOOR, OUTDOOR, ONEPUSH, AWB, or MANUAL. 4. Press the OPEN key or use joystick to save settings. 5. Press the CLOSE key or use joystick to return to previous menu (back). 3.5.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE To use this menu: 1. Open the MAIN MENU. 2. Select CAMERA SETUP using the joystick [u], then move to AE SETUP using the joystick. 3. Set the MODE to FULL, AUTO, MANUAL, or SHUTTER PRI. 4. Press the OPEN key or use joystick to save settings. 5. Press the CLOSE key or use joystick to return to previous menu (back). 3.5.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 3.5.5 ADVANCED SETUP menu Sharpness enhances picture detail by increasing the aperture gain of the camera and sharpening the edges in the picture. Sharpness enhances picture detail by increasing the aperture gain of the camera and sharpening the edges in the picture. In the ADVANCED SETUP menu, only one of the following four modes can be selected: • • • • BLC: Back light compensation.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 3.6 DOME MOTION SETUP menu To navigate within the menu system: • • • • p/q: move joystick up and down for selecting an item. t/u: move joystick left and right for moving an item. u/ [OPEN]/ [NEAR]: move joystick right to select or save values or go to edit pages. u/ [CLOSE]/ [FAR]: move joystick to cancel or to exit current menu (back) 3.6.1 GENERAL SETUP menu This menu control general function of dome. To use this menu: 1. Open the MAIN MENU. 2.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 4. Set the TURBO SPEED option to ON or OFF. —— Turbo speed defines the pan and tilt speed only for the manual operation of Pan/Tilt. 5. Set the PRESET SPEED to FAST, NORMAL, or SLOW. 6. Press the OPEN key or use joystick to save settings. 7. Press the CLOSE key or use joystick to return to previous menu (back). 3.6.2 MOTION SETUP menu To use this menu: 1. Open the MAIN MENU. 2.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 6. Press the OPEN key or use joystick to save settings. 7. Press the CLOSE key or use joystick to return to previous menu (back). 3.6.3 HOME ACTION SETUP menu The Home Action setup menu is used to force the camera to a specific action – home, preset, pattern, tour or scan – after the joystick control is idle for specific time. Before a “preset” associated with an action can be selected, it must be pre-established. The time can be set from 1 ~ 60 minutes.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 3.6.4 CALIBRATION SETUP menu 1. Set the AUTO CAL option to MANUAL or AUTO using the joystick [u]. —— In MANUAL mode, use the joystick [u] to select CALIBRATION to execute. 2. Set the ERROR MSG DISP option to ON or OFF. 3. Press the OPEN key or use joystick to save settings. 4. Press the CLOSE key or use joystick to return to previous menu (back). NOTE Calibration is a function for automatically correcting an error on the angle of Pan/Tilt.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE To navigate within the menu system: • • • • p/q: move joystick up and down for selecting an item. t/u: move joystick left and right for moving an item. u/ [OPEN]/ [NEAR]: move joystick right to select or save values or go to edit pages. u/ [CLOSE]/ [FAR]: move joystick to cancel or to exit current menu (back). You can configure up to 210 preset positions. Each preset includes Pan/Tilt/Zoom. Use the following steps to construct a PRESET: 1. Open the MAIN MENU.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 3.8 PATTERN SETUP menu To navigate within the menu system: • • • • p/q: move joystick up and down for selecting an item. t/u: move joystick left and right for moving an item. u/ [OPEN]/ [NEAR]: move joystick right to select or save values or go to edit pages. u/ [CLOSE]/ [FAR]: move joystick to cancel or to exit current menu (back). A Pattern is used to display (or recall) a memorized, repeated and serial trace of pan, tilt, zoom.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 4. Using the joystick, move to the desired target position, then press the NEAR key to start configuring the pattern. —— —— Press the NEAR key or use joystick to save settings. Press the FAR key or use joystick to return to previous menu (PATTERN SETUP) (back). 5. Press the OPEN key or use joystick to save settings. 6. Press the CLOSE key or use joystick to return to previous menu (back). 3.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE —— —— —— Change the mode with the NEAR key. u/ [OPEN]/ [NEAR]: move joystick right to select or save values or go to edit pages. u/ [CLOSE]/ [FAR]: move joystick to cancel or to exit current menu (back). 3.10 SCAN SETUP (auto scan) menu To navigate within the menu system: • • • • p/q: move joystick up and down for selecting an item. t/u: move joystick left and right for moving an item.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE —— —— 3. To edit and clear a scan title, select EDIT. To clear a saved scan number, select CLEAR. Move the joystick right [u] to edit an AUTO SCAN: edit START POSITION / edit STOP POSITION. —— —— —— Using the joystick, move to a desired target position (pan / tilt / zoom) of edit START POSITION / edit STOP POSITION. Press the NEAR key or use the joystick to save settings. Press the FAR key or use the joystick to return to the SCAN SETUP menu (back). 4.
SECTION 3: SOFTWARE SETUP - OPERATING GUIDE 3. Using the joystick [u], select the alarm input type (normally open, NO or normally closed, NC). 4. Using the joystick [u], select the alarm output state (ON / OFF). 5. Set the alarm PRIORITY using the joystick. 6. Set the ACTION (Off, Preset, Pattern, Scan, or Tour) and the action NUMBER. The numbered action must be predefined. 7. Set the DTIME (alarm action time, 3 ~ 60 s). The default setting is ON.
SECTION 4: OSD MENU STRUCTURE REFERENCE SECTION 4 OSD Menu Structure Reference 4.
SECTION 4: OSD MENU STRUCTURE REFERENCE 4.
SECTION 4: OSD MENU STRUCTURE REFERENCE 4.
SECTION 4: OSD MENU STRUCTURE REFERENCE 4.4 Miscellaneous submenus 4.
SECTION 5: SPECIFICATIONS SECTION 5 Specifications Table 2. Component Specifications Parameter Value General Image device 1/3" CMOS Effective pixels ~ 2.1 Megapixel Video signal HD: 1920 x 1080 (full-HD,1080p @ 30 fps), 1280 x 720 (HD, 720p @ 60 fps) SD: NTSC, PAL Lens 12x optical /10x digital zoom (auto focus) View angle 52.4° (wide end) to 4.
SECTION 5: SPECIFICATIONS Parameter Value Auto scan 8 auto scan, includes vector scan Preset position 210 position with camera status Tour 8 tour (preset, pattern, scan) Pattern 8 pattern On Screen Display (OSD) Display camera ID, title, mode, and angle on screen (multi-language) OSD language options English, Chinese, Russian, Spanish, German, Italian, French, Netherlandish Environment Operating Temperature 14 °F ~ 122 °F (-10 °C ~ 50 °C) Heater on: -40 °F ~ +50 °F (-40 °C ~ +10 °C) Heater
APPENDIX A: TROUBLESHOOTING APPENDIX A Troubleshooting If problems occur, check the installation of the dome with the instructions in this manual. And refer to this manual for further information. Problem Solution No video on the screen - Verify that power is connected to all components in the system. - Verify that the power switches are ON. - Verify the status of cables or connection of cables Poor video quality. - Check the power supply voltage (normal 24 Vac) - Check the setting of camera.
APPENDIX B: CAMERA DIMENSIONS APPENDIX B Camera Dimensions Top view 13.43” 10.16” Side view 10.04” 5.51” 6.34” Front view 4.41” 4.72” 6.
APPENDIX C: PELCO PROTOCOL FUNCTION LIST APPENDIX C Pelco™ Protocol Function List LCD display Function keys: F1 (PSET), F2 (TOUR), F3 (PATT), F4 (SCAN) ESC / POWER Joystick Number keys Controller function keys Camera focus control PTZC4 PTZ controller Table 3. Pelco functions based on Observint Technologies PTZC4 controller Function Key Preset number Operation Example 1 Example 2 Preset Preset 1 ~ 59, 101 ~ 253 No.
46
