Installation guide

ManualsBrandsBlack ManualsComputer equipmentBLK-IPE101

www.digiop.com

BLK-IPE101_PQ

5/13/11

Step 3. Install IPAdmin Tool

The IPAdminTool is a utility for conguring the network settings of your Digiop Black encoders and

installing new rmware. It can be loaded on a Microsoft Windows XP, Vista or Windows 7 operating

system. At a computer on the same LAN (subnet) where your encoders will be installed, do the following:

1. Insert the CD mini disk provided with your camera into your computer’s CD ROM drive and open the

CD in a Windows Explorer window.

2. Find the IPAdminTool directory on the CD.

3. Copy the IPAdminTool directory with its contents to your computer hard drive.

Step 4. Configure the network settings of you encoder

When your IP encoder is attached to a network and initially powered on, it attempts acquire compatible

network settings from a DHCP server. If it cannot nd a DHCP server, it congures itself with the following

static (xed) settings, which may or may not be compatible with other devices on the network.

IP address: 192.168.0.100

Subnet mask: 255.255.255.0

Gateway: 192.168.0.1

Your encoder must be congured with static network settings that are compatible with the LAN. If your

LAN has a DHCP server, use the following sub-step. Otherwise, use the sub-step procedure below for LANs

without DHCP.

Installing encoders on LANs with DHCP

1. Connect your encoder to the LAN, then power on the encoder.

2. Open the directory IPAdminTool directory on your computer, then double click the le

IPAdminTool.exe to start the application. When the IPAdmin Tool starts, it will discover all the IP

devices it supports that exist on the network. The discovery process may take a few minutes.

Review the list of IP devices found by IPAdmin Tool. You can identify your encoder by the MAC

address. If the encoder was not found, click the Refresh button every minute until your encoder

appears in the list.

3. After nding your encoder, right click the entry, then select IP Address from the drop-down list. An

IP Setup window will open.

Static Option

4. In the IP Setup window, click the Static option bullet. If you have other compatible network settings

you want to apply to the device, enter them in the appropriate locations. Click Setup to save

settings.

H.264 Network Video Encoder

Quick Installation Guide

This document guides you through the basic steps to install and congure your Digiop® Black BLK-IPE101 IP

encoder. For detailed instructions, refer to the User Manual.

Find the encoder’s MAC address on the product label and enter it here: __________________

Step 1. Install the encoder

Mount the encoder in a secure location using the hardware installation kit provided. The kit includes

mounting brackets that slip onto the sides of the encoder.

Connect an analog signal source (camera video) to the Vin BNC connector on the front of the encoder.

Connections to the encoder for audio in and out (microphone and speaker), D/I sensor, alarm, video out

BNC, RS-232C, and RS-485 control are made through two 9-pin terminal blocks.

Attach peripheral devices to the terminal blocks as shown below. For detailed interface specications, refer

to the user manual.

Attach the video stream from your analog camera to the encoder Vin BNC connector.

Step 2. Connect the encoder to the LAN

Attach the network LAN cable to the RJ-45 connector on the encoder backpanel.

If the encoder is not powered through the Ethernet (PoE), attach the DC12V adapter to the power connector

on the encoder and plug the power adapter into a power source. DO NOT apply power to the encoder at

this time.

Summary of content (3 pages)

PAGE 1
H.264 Network Video Encoder Quick Installation Guide This document guides you through the basic steps to install and configure your Digiop® Black BLK-IPE101 IP encoder. For detailed instructions, refer to the User Manual. Find the encoder’s MAC address on the product label and enter it here: __________________ Step 1. Install the encoder Mount the encoder in a secure location using the hardware installation kit provided. The kit includes mounting brackets that slip onto the sides of the encoder. Step 3.
PAGE 2
5. In the Login window, enter the ID and PW (password) for your encoder, then click Login. The default administrator values for the ID and PW are root and pass. The “Request timed out” response indicates that the IP address is not in use and the encoder can be connected without causing conflicts. If the response from the ping command received a “Reply..”, the IP address is in use. Contact Technical Support for further assistance, if needed. Find network settings (IP addresses) that are not in use 1. 6.
PAGE 3
5. 6. 7. In the IP Setup window: a. Select the Static option if it is not selected. b. Enter the new IP address for your encoder into the IP Address field. c. Enter the subnet mask of your computer into the Subnet Mask field. d. Enter the gateway of your computer into the Gateway field. e. Click SETUP. A Login window will open. In the Login window, enter the ID and PW (password) for your encoder and click Login. The default administrator values for the ID and PW are root and pass.