Installation Instructions
WHAT YOU WILL NEED
Blast Gauges
PC with Windows 7, 8 or 10
Blast Gauge System Manager software (BGSM)
(steps 1-2)
Micro-USB cables and hub for activation
- optional (BGK7 Kit)
Tablet running Android
™
or iOS
Blast Gauge App for Android or iOS
(step 3)
Certifications
United States: FCC ID: 2AHN8BG711
Canada: IC ID: 21433-BG711
Australia: RCM000577
FCC/IC Statement
FCC § 15B
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation
Cet appareil est conforme à la partie 15 des règles de la FCC. Le fonctionnement est soumis aux deux conditions
suivantes: (1) ce dispositif ne peut pas causer d’interférences nuisibles, et (2) cet appareil doit accepter toute
interférence reçue, y compris les interférences qui peuvent causer un mauvais fonctionnement.
FCC § 15.21
Changes or modications made to this equipment not expressly approved by BlackBox Biometrics Inc. could void
the user’s authority to operate the equipment
FCC § 15.105
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense
WARNING!
FCC and IC Radiation Exposure Statement:
This portable equipment with its antenna complies with FCC’s and IC’s RF radiation exposure limits set forth for an
uncontrolled environment. To maintain compliance, follow the instructions below:
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Avoid direct contact to the antenna, or keep contact to a minimum while using this equipment.
Cet équipement portable avec son antenne est conforme aux limites d’exposition aux rayonnements RF de la
FCC et IC de dénies pour un environnement non contrôlé. Pour maintenir la conformité , suivez les instructions
ci-dessous:
Cet émetteur ne doit pas être situé ou opérant en conjonction avec une autre antenne ou émetteur.
Éviter tout contact direct à l’antenne , ou garder le contact à un minimum tout en utilisant cet équipement .
Radio Standards Procedure
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two
conditions:
This device may not cause interference; and
This device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme aux CNR exempts de licence d’Industrie Canada. Le fonctionnement est soumis aux deux
conditions suivantes:
Ce dispositif ne peut causer des interférences; et
Cet appareil doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais
fonctionnement de l’appareil.
Declaration of Conformity
BlackBox Biometrics, Inc. of 125 Tech Park Drive, Rochester, NY declares under our sole responsibility the Wireless
Blast Gauge® System 7.0 & 7.1 are in conformity with the following standards:
Low Voltage Directive – 2014/35/EU
EMC Directive – 2014/30/EU
RoHS (Restriction of Hazardous Substances) Directive – 2011/65/EU
R&TTE Directive – 1999/5/EC
which is indicated and armed by the applied CE marking
Intended use of equipment: Measure exposure to blast overpressure in range 0.5-110 psi, at resolution of 0.05 psi.
Precautions for Safe Handling: The Blast Gauge® System has been designed and manufactured for use by qualied
personnel for the purpose of measuring exposures to blast overpressure.
Safety considerations are contained in the Safety Data Sheet (SDS) available by request.
Storage: Shelf life is greater than 5 years in cool (15 ºC - 25ºC), dry and ventilated areas, which are subject to little
temperature change. Do not place the article near heating equipment, nor expose to direct sunlight for long
periods. Elevated temperatures can result in shortened battery life and degrade performance.
Disposal: This Product contains a lithium battery that is not rechargeable or replaceable. Normally the article has
no odor. Under normal conditions of use, the battery, its electrode materials and its hazardous liquid electrolyte
are non-reactive provided the battery integrity is maintained. The battery will release a pungent corrosive odor if
leaking.
There are no federal regulations for disposal of lithium batteries. Individual states or localities establish their own
guidelines for battery disposal, and should be contacted for any disposal guidelines that they may have for a lithium
metal batteries.
Disclaimer
The Blast Gauge
®
System is not intended to diagnose or treat the blast victim’s
injuries. The rst responder may use the Blast Gauge System data to
characterize the blast overpressure and acceleration the subject sustained
during an event, but will rely on standard diagnostic protocols to drive
treatment of the subject’s injuries.
Copyright © 2019 BlackBox Biometrics, Inc. All Rights Reserved.
BlackBox Biometrics, Inc.
125 Tech Park Drive, Rochester, NY 14623
585.329.3399
BlastGauge.com
P0012 4.6
13. Attach your gauges to personnel or to a structure.
16. If there is not a tablet available, press the recessed
button to check LED status.
START SCAN
14. Select either Quick Scan for summary data, or Full
Scan for full waveform data.
17. To transfer Blast Gauge data from the tablet to your
PC, refer to the Tablet to PC Data Transfer Guide.
For more information, see
What do I need to know?
15. Wirelessly retrieve data from the gauges by clicking
Start Scan on the tablet.