WT-1004 Walkie-Talkie User Manual
WT-1004 Instruction Manual 12 1 3 1. 2. 3. 4. 5. 6. 2 8 4 6 9 7 5 10 11 7. 8. 9. 10. 11. 12.
1. VOX 2. Dual Watch 3. RX 4. TX 5. Main Channel Number 9 10 6. Speaker Volume 7. Key Lock 11 12 8. APO (Auto Power Off) 9. Battery Level LCD DISPLAY ICONS 1 2 3 8 4 5 6 13 7 14 10. DCS 11. Code for CTCSS/ DCS 12. CTCSS 13. Scan 14. Call tone MAIN FEATURES ● Frequency: 462MHz ● Power output ＜0.
PRECAUTIONS ● Read this manual before use the radio. ● Avoid the direct exposure to solar rays and/or in front of heat. ● Do not use adaptor and/or batteries diverged from that specified on instructions manual. ● Do not operate the radio in hazardous environments, explosion or fire may result. ● Do not operate the radio in high humidity, dusty, or explosive environment. ● Clean by using a cloth slightly dampened. Do not use alcohol, solvents or abrasives etc. ● Do not attempt to modify the radio.
WARNING ● Follow the polar directions and insert 3 X AAA Ni-MH rechargeable batteries. ● Incorrect positioning can damage both the batteries and unit. ● Don’t try to recharge non-rechargeable batteries. ● Make sure the battery compartment cover is securely locked in place when you are charging the batteries. ● Dispose of used batteries safely and in a way that will not harm the environment, never try to burn them or put them anywhere, they could get burnt or punctured.
GENERAL OPERATIONS 1. TRANSMITTING RANGE ● The talk range depends on the environmental and terrain. It will be reach (up to about 10 KM) in wide open spaces, without obstructions such as hills or buildings. Don’t try to use two PMR units which are less than 1.5m apart. If you do, ou may have experience interference. 2. POWER ON/OFF ● To power on the radio, press Power On/Off key for 2 seconds until a beep is heard and the LCD display turn on.
● When you finish speaking, release the PTT key and a beep tone will be heard. 5. LISEN TO OTHER RADIO ● The radio will automatically sound received signal from the other radio with the same channel and LCD show the icon . ● When you press the PTT key, you can’t listen to other radios. Make sure you do not press the PTT key, you can’t listen to other radios. Make sure you do not press PTT key for listening. ● Adjust volume control if necessary. 6.
MENU FLOW CHART Press Menu key once to enter main channel selection, press again for next function selection etc. Main screen Main Channel CTCSS DCS VOX Call tone Auto Power Off Beep Tone Roger Beep Main screen 9. SELECT CHANNEL To select the main channel ● Press the Menu key once, Main channel number displayed will flash. ● Press ▲ or ▼ key to select your desired main channel number. ● Press the PTT key to confirm and quit or press to continue next function setting.
● ● Press ▲ or ▼ key to select your desired CTCSS code from 1 to 38, 0 is OFF. Press the PTT key to confirm and quit. 10.2 DCS Code Each channel also has 83 digital codes to let you set up group of users for more secured private communication. ● Press the MENU key 3 times, DCS code display will flash. ● Press ▲ or ▼ key to select your desired DCS code from 1 to 83, 0 is OFF. ● Press the PTT key to confirm and quit. 11.
12. SENDING CALL TONE You can use 1of 10 different “Call Tones” to get attention of other user on the same channel. ● Press the music key and the tone will sound, LCD will display the transmit icon and icon and your call tone will be sent. 13. SELECTING CALL TONE ● ● ● Press the Menu key 5 times, LCD display icon and call tone number will flash. Press ▲ or ▼ key to select your desired call tone. Press the PTT key to confirm and quit or press Menu to continue next function setting. 14.
15. KEY TONE ON/OFF The unit has the function to turn the beep tone on or off. ● Press Menu key 7 times, LCD display “t o”. ● Press ▲ or ▼ key to turn on (LCD display ON icon) or turn off (LCD display OF icon). ● Press PTT to confirm and quit or press Menu to continue next function setting. 16. ROGER BEEP The roger beep function enables a short tone signal which is transmitted after releasing the PTT button.
● ● ● Press Menu key 8 times, LCD display “r o”. Press ▲ or ▼ key to turn on (LCD display ON icon) or turn off (LCD display OF icon) Press PTT to confirm and quit or press MENU to continue next function setting. 17. SCANNING CHANNELS ● Press the key once and LCD will display and radio will start scanning. ● LCD display shows the scanning channel one by one. ● It will stop at those channels with signal for a while,and LCD will diasplay icon, ● Press ▲ or ▼ key to continue scanning.
18. MONITOR Press and hold key to break the squelch noise and open (un-squelch) the frequency for monitor function. Release the key to stop. 19. KEY LOCK Press and hold key for 3 seconds, LCD display icon. All keys are locked expect PTT and key. To unlock, press and hold key for 3 seconds again. SPECIFICATIONS Operation Frequency Range Modulation RF Output Power Channels CTCSS sub-code DCS sub-code Power Supply : : : : : : : 462.5625 ~ 462.
Channel Frequency Table Channel Frequency（MHz) Channel Frequency（MHz) 1 462.5625 12 467.6625 2 462.5875 13 467.6875 3 462.6125 14 467.7125 4 462.6375 15 462.5500 5 462.6625 16 462.5750 6 462.6875 17 462.6000 7 462.7125 18 462.6250 8 467.5625 19 462.6500 9 467.5875 20 462.6750 10 467.6125 21 462.7000 11 467.6375 22 462.
CAUTION Risk of explosion if battery is replaced by an incorrect, dispose of used batteries according to the instructions Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules.
• • • • • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy. The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR The SAR limit set by the FCC is 1.6W/Kg.
For more detailed information about recycling of this product, please contact your local city office or your household waste disposal service. SEM-PKSK601OT Ver.
