Manual

ManualsBrandsBLACKHAWK! ManualsSports and recreationAXIOM U/L RIFLE STOCK CAMO FINISH

www.BLACKHAWK.com

BLACKHAWK!

NORFOLK, VA U.S.A. 1.800.694.5263

50107098 REV. 04.09

AXIOM Rifle Stock

Owner’s Manual

™

Page 1

www.BLACKHAWK.com

BLACKHAWK!

NORFOLK, VA U.S.A. 1.800.694.5263

Installation Instructions

ATTENTION: Read and follow all instructions and warnings prior to installation and/or fir-

ing a Axiom equipped firearm. Take extra time to review the shooting tips & techniques

section of this manual (Page 7). If you are at all unsure of your ability to install your Axiom

Rifle Stock safely, please seek the services of a competent gunsmith.

WARNING 1: Before beginning stock installation, make sure that the rifle is UN-

LOADED. Carefully check the chamber and magazine making both visual and touch ver-

ification.

WARNING 2: The Axiom Rifle Stock is not compatible with oversized trigger guards.

Use of the Axiom Rifle Stock with an oversized trigger guard will cause product failure and

possible injury. Note: Most factory installed trigger guards are compatible with the Axiom

Rifle Stock.

WARNING 3: The Axiom Rifle Stock is not compatible with trigger guard mounted

oversized safeties. Use of the Axiom Rifle Stock with an oversized safety will cause prod-

uct failure and possible injury.

TOOLS REQUIRED:

• Large Flat Blade Screw Driver

• Hex Key / Allen Wrench Set

• Torque Wrench (Recommended)

• Extended “ball end” Allen Wrench (Included)

INSTALLATION STEPS:

1. Remove action bolt from receiver. Remove original stock. Refer to manufacturer’s in-

structions for the best method to remove stock. Normally the barreled action is held in po-

sition by two screws located on the bottom of the stock. Using caution not to damage

screws, use the appropriate size and type of tool to remove the two screws (Fig. 1A).

Note: At this point the trigger guard is disconnected from the stock. For BDL models re-

move bottom magazine floor plate along with magazine housing. (Fig. 1B on the follow-

ing page) Remove barreled action from stock. To avoid damage, take caution when

removing barreled action from original stock.

Fig. 1A

Summary of content (6 pages)

PAGE 1
Page 1 AXIOM Rifle Stock Owner’s Manual Installation Instructions ™ ATTENTION: Read and follow all instructions and warnings prior to installation and/or firing a Axiom equipped firearm. Take extra time to review the shooting tips & techniques section of this manual (Page 7). If you are at all unsure of your ability to install your Axiom Rifle Stock safely, please seek the services of a competent gunsmith. WARNING 1: Before beginning stock installation, make sure that the rifle is UNLOADED.
PAGE 2
Page 2 Installation Instructions Continued Page 3 Installation Instructions Continued 4. Carefully insert receiver or barreled action into the forend. Carefully align recoil lug and trigger with corresponding pockets or openings. Slowly lower barreled action into forend until it is fully seated. (Fig. 4) Note: The barreled action should slide into position with limited hand pressure and when in final position there should very minimal movement. Fig. 1B 2.
PAGE 3
Page 4 Installation Instructions Continued Page 5 Installation Instructions Continued 6. Reinstall trigger guard and hinged magazine floor plate assembly. (Fig. 6) Note: It is crucial that the trigger guard and hinged magazine floor plate assembly is properly seated in the stock prior to final installation and torquing of bolts. 8. Reinstall action bolt into receiver. (See owners manual for directions) 9. Reattach pistol group portion of stock to forend.
PAGE 4
Page 6 Page 7 Axiom Operational Information Shooting Tips & Techniques To extend the Stock, grasp the release lever located on the bottom side of the stock. Squeezing the lever releases the lock and allows the stock to slide freely to the desired position. The lock will automatically engage at each position.(Fig. A) IMPORTANT NOTICE: During recoil, the Rifle moves rearward over the pistol grip by slightly more than one inch. Fig. A RIGHT: Maintain at least 1" space between cheek and flare in stock.
PAGE 5
Page 8 Page 9 Cheek Rest Accessory Installation Sling Mounting Tips (PART# K99900-C) NOTE: Alignment with scopes or raised sights can be improved by purchasing cheek rest accessory part# K99900-C. Please contact BLACKHAWK! for ordering information. INSTALLATION STEPS: 1. Determine the correct height cheek rest.
PAGE 6
Page 10 Product Maintenance & Information Customer Satisfaction & Service CUSTOMER SATISFACTION: MAINTENANCE: Do not attempt to disassemble or adjust any of the recoil mechanisms. The internal springs have a 40,000+ round life expectancy and should not require replacement. As part of regular firearm maintenance apply a small amount of "plastic safe" lubricant (not WD-40) to metal and moving surfaces. Very little lubrication is required so use sparingly (1-2 drops).