Porto-Power Blackhawk Automotive is a licensed trademark Porto-Power Kit Operating Instructions & Parts Manual U.S. PATENT 5,520,400 Model Number B65114 B65115 Capacity 4 Ton 10 Ton SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153 816-891-6390 sales@blackhawk-automotive.
ONE YEAR LIMITED WARRANTY For a period of one (1) year from date of purchase, SFA Companies will repair or replace, at its option, without charge, any of its products which fails due to a defect in material or workmanship under normal usage. This limited warranty is a consumer's exclusive remedy. Performance of any obligation under this warranty may be obtained by returning the warranted product, freight prepaid, to SFA Companies Warranty Service Department, 10939 N. Pomona Ave., Kansas City, MO 64153.
SAVE THESE INSTRUCTIONS For your safety, read and understand the information contained within. The owner and operator shall have an understanding of this product and safe operating procedures before attempting to use this product. Instructions and Safety information shall be conveyed in the operator's native language before use of this product is authorized. Make certain that the operator thoroughly understands the inherent dangers associated with the use and misuse of the product.
SAFETY INSTRUCTIONS BEFORE USE (Refer to Figure 1 on page 3) 1. Study, understand, and follow all instructions provided with and on this device before use. 2. Inspect before each use. Do not use if bent, broken, leaking or damaged components are noted. 3. Ensure that product and application are compatible. 4. Check to ensure that all parts of your kit are included (see illustration and parts list on page 10 & 11). 5. Carefully remove the dust covers and plugs from hose coupler and ram coupler. 6.
! WARNING! ! WARNING • Ram must be on a stable base, which is able to support the load while pushing or lifting. • Ensure ram is fully engaged into/onto adapters, extension accessories. • To help prevent personal injury, use shims, friction material or constraints to prevent slippage of the base or load. • Do not off-center loads on a ram. The load can tip or the ram can "kick out" and cause personal injury. • As the load is lifted, use blocking and cribbing to guard against a falling load.
OPERATION Note: Inspect before each use for evidence of fluid leaks, damaged hydraulic fittings, bent or broken attachments and missing parts. 1. Locate and close release valve by turning it clockwise until firmly closed. (Do not over tighten) 2. Operate by pumping handle. This will send fluid from the pump reservoir into the high pressure hose assembly and into the ram assembly. 3. Continue pumping until ram reaches desired height.
Basic Setup The capacity of the Porto-Power Kit can be significantly affected by the number of attachments used and the type of load applied. The approximate load capacity of each function setup is illustrated below. When two or more extension tubes are used together, be sure to position the shortest tube further away from the ram. Note: Not all accessories in the illustrations provided in the Porto-Power Kit. A.
TROUBLESHOOTING Symptom Possible Causes Corrective Action Ram will not extend • Release valve not tightly closed • Overload condition • Ensure release valve tightly closed • Remedy overload condition Ram will not lift to full extension • Fluid level low • Ensure proper fluid level Spongy effect • Air trapped in system • Bleed air from system Ram *bleeds off after lift • Release valve not tightly closed • Dirt in pump's return check valve • Hydraulic unit malfunction • Ensure release valve tigh
Replacement Parts for Model B65114 Item # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 - Part # B65161 B65160 B65159 B65158 B65157 B65177 B65153 B65151 B65156 B65154 B65155 B65178 B65152 B65123 434-6-3313-101 434-6-3312-109 B69478 B69477 B65187 426-3-1301-203 431-6-1702-404 B65291 324-4-1900-208 B65186 B65067 B65114-L0 B65114-M0 Description Extension Tube (19-1/2") Extension Tube (16-1/2") Extension Tube (8-1/2") Extension Tube (6-1/8") Extension Tube (3") Male connector Wedge Head (o
Replacement Parts for Model B65115 Item# Part# 1 B65162 2 B65163 3 B65164 4 B65165 5 B65179 6 B65166 7 B65167 8 B65168 9 B65172 10 B65169 11 B65180 12 B65173 13 B65123 14 434-6-3313-101 15 434-6-3312-109 16 B69478 17 B69477 18 B65189 19 426-3-1301-203 20 430-6-1702-407 21 B65291 22 324-4-1900-208 23 B65188 24 B65068 B65115-L0 B65114-M0 Description Extension Tube (27") Extension Tube (18") Extension Tube (10") Extension Tube (4") Male Connector Wedge Head (offset) Serrated Saddle Flat Base Plunger Toe (offs
Load - Pressure Correlation For Model B65114 & B65115 Always monitor the force applied to workpiece by using a load cell and indicator or you may monitor pressure developed in the ram by using an inline pressure gauge, then calculate the applied force using the formula: where F = Force/ Load (lbs); P = Hydraulic working pressure (psi) and; A = Ram effective area (in²) F=PxA For model B65114, A = 0.998 in² ; For model B65115, A = 2.
memo.