User's Manual
Table Of Contents
- Getting Started
- Using Blackmagic SmartView Setup
- Using SmartView 4K
- Using SmartScope Duo 4K
- Connecting to a Network
- Adjusting Network Settings
- Using Tally
- Optimizing the Viewing Angle
- Developer Information
- Help
- Regulatory Notices and Safety Information
- Warranty
- English
- 日本語
- Français
- Deutsch
- Español
- 中文
- 한국어
- Русский
- Italiano
- Português
- Türkçe
- はじめに
- Blackmagic SmartView Setupの使用
- SmartView 4Kの使用
- SmartScope Duo 4Kの使用
- ネットワークに接続
- ネットワーク設定の調整
- タリーの使用
- ビューアングルの最適化
- デベロッパーの皆様へ
- ヘルプ
- 規制に関する警告および安全情報
- 保証
- Mise en route
- Utiliser le Blackmagic SmartView Setup
- Utiliser le SmartView 4K
- Utiliser SmartScope Duo 4K
- Connexion à un réseau
- Modifier les paramètres réseau
- Utilisation du tally
- Optimiser l'angle de vision
- Developer Information
- Assistance
- Avertissements et informations de sécurité
- Garantie
- Erste Schritte
- Blackmagic SmartView Setup im Einsatz
- Der SmartView 4K im Einsatz
- Der SmartScope Duo 4K im Einsatz
- Anschließen an ein Netzwerk
- Anpassen von Netzwerkeinstellungen
- Arbeiten mit Tally
- Optimieren des Betrachtungswinkels
- Informationen für Entwickler (Englisch)
- Hilfe
- Gesetzliche Vorschriften und Sicherheitshinweise
- Garantie
- Primeros pasos
- Uso del programa SmartView Setup
- SmartView 4K
- SmartScope Duo 4K
- Conexión a redes
- Ajustes de red
- Sistemas de señalización
- Mejora del ángulo de visión
- Información para desarrolladores
- Ayuda
- Información sobre normativas y seguridad
- Garantía
- 入门
- 使用Blackmagic SmartView Setup
- 使用SmartView 4K
- 使用SmartScope Duo 4K
- 连接到网络
- 调整网络设置
- 使用Tally
- 调整最佳监看角度
- Developer Information
- 帮助
- 监管告知与安全信息
- 保修
- 시작하기
- Blackmagic SmartView Setup 소프트웨어 사용하기
- SmartView 4K 사용하기
- SmartScope Duo 4K 사용하기
- 네트워크에 연결하기
- 네트워크 설정 조정하기
- 탈리 사용
- 시야각 최적화하기
- 지원
- 규제 사항 및 안전 정보
- 보증
- Подготовка к работе
- Работа с утилитой Blackmagic MultiView Setup
- Работа со SmartView 4K
- Работа со SmartScope Duo 4K
- Подключение к локальной сети
- Изменение сетевых настроек
- Индикация состояния
- Регулировка угла обзора
- Информация для разработчиков
- Помощь
- Соблюдение нормативных требований и правила безопасности
- Гарантия
- Operazioni preliminari
- Utilizzare Blackmagic SmartView Setup
- Utilizzare SmartView 4K
- Utilizzare SmartScope Duo 4K
- Collegarsi ad una rete
- Regolare le impostazioni di rete
- Utilizzare la funzione tally
- Ottimizzare l’angolo di visuale
- Informazioni per gli sviluppatori (English)
- Assistenza
- Normative e sicurezza
- Garanzia
- Instruções Preliminares
- Usar Blackmagic SmartView Setup
- Usar SmartView 4K
- Usar SmartScope Duo 4K
- Conectar a uma Rede
- Ajustar Configurações de Rede
- Usar Sinalização
- Otimizar o Ângulo de Visualização
- Informações para Desenvolvedores
- Ajuda
- Informações Regulatórias e de Segurança
- Garantia
- Başlarken
- Blackmagic SmartView Setup Yazılımının Kullanımı
- SmartView 4K’nın Kullanımı
- SmartScope Duo 4K Kullanımı
- Bir Ağa Bağlanırken
- Ağ Ayarlarının Değiştirilmesi
- Tally Özelliğinin Kullanılması
- İzleme Açısının Optimize Edilmesi
- Yazılım Geliştirici Bilgileri
- Yardım
- Düzenleyici Bildirim ve Güvenlik Bilgileri
- Garanti
The histogram display setting showing
distribution of whites to blacks
Select histogram from the ‘display’ drop down
menu in Blackmagic SmartView setup
Audio Metering Display
The audio metering displays show you the audio levels in the embedded audio of the SDI video
signal. Up to 16 channels of embedded audio are de-embedded and then displayed in either
dBVU or dBFS format.
The VU meter shows average signal levels, is easy to use and very common on older equipment.
VU is calibrated to the SMPTE recommendation of a 1 kHz tone test signal set to -20 dBFS.
dBFS is essentially a meter of the overall digital audio signal and is common on modern digital
equipment.
The right hand audio scope can monitor two channels of audio, which can be selected from the
‘set’ drop down menu. e.g., ch 1 & 2, ch 3 & 4, etc. The audio scope presents audio in an X-Y
view so you can see audio balance issues, out of phase conditions and whether an audio track
is mono or stereo. Mono audio should appear as a single vertical “in phase” line. If the line is
horizontal, then your audio is “out of phase” and could cancel out (i.e., loss of audio) when
received by downstream equipment. Audio phase is one of the most common audio faults in
large facilities, where cables can be incorrectly connected.
21Using SmartScope Duo 4K