User's Manual
Table Of Contents
- Getting Started
- Using Blackmagic SmartView Setup
- Using SmartView 4K
- Using SmartScope Duo 4K
- Connecting to a Network
- Adjusting Network Settings
- Using Tally
- Optimizing the Viewing Angle
- Developer Information
- Help
- Regulatory Notices and Safety Information
- Warranty
- English
- 日本語
- Français
- Deutsch
- Español
- 中文
- 한국어
- Русский
- Italiano
- Português
- Türkçe
- はじめに
- Blackmagic SmartView Setupの使用
- SmartView 4Kの使用
- SmartScope Duo 4Kの使用
- ネットワークに接続
- ネットワーク設定の調整
- タリーの使用
- ビューアングルの最適化
- デベロッパーの皆様へ
- ヘルプ
- 規制に関する警告および安全情報
- 保証
- Mise en route
- Utiliser le Blackmagic SmartView Setup
- Utiliser le SmartView 4K
- Utiliser SmartScope Duo 4K
- Connexion à un réseau
- Modifier les paramètres réseau
- Utilisation du tally
- Optimiser l'angle de vision
- Developer Information
- Assistance
- Avertissements et informations de sécurité
- Garantie
- Erste Schritte
- Blackmagic SmartView Setup im Einsatz
- Der SmartView 4K im Einsatz
- Der SmartScope Duo 4K im Einsatz
- Anschließen an ein Netzwerk
- Anpassen von Netzwerkeinstellungen
- Arbeiten mit Tally
- Optimieren des Betrachtungswinkels
- Informationen für Entwickler (Englisch)
- Hilfe
- Gesetzliche Vorschriften und Sicherheitshinweise
- Garantie
- Primeros pasos
- Uso del programa SmartView Setup
- SmartView 4K
- SmartScope Duo 4K
- Conexión a redes
- Ajustes de red
- Sistemas de señalización
- Mejora del ángulo de visión
- Información para desarrolladores
- Ayuda
- Información sobre normativas y seguridad
- Garantía
- 入门
- 使用Blackmagic SmartView Setup
- 使用SmartView 4K
- 使用SmartScope Duo 4K
- 连接到网络
- 调整网络设置
- 使用Tally
- 调整最佳监看角度
- Developer Information
- 帮助
- 监管告知与安全信息
- 保修
- 시작하기
- Blackmagic SmartView Setup 소프트웨어 사용하기
- SmartView 4K 사용하기
- SmartScope Duo 4K 사용하기
- 네트워크에 연결하기
- 네트워크 설정 조정하기
- 탈리 사용
- 시야각 최적화하기
- 지원
- 규제 사항 및 안전 정보
- 보증
- Подготовка к работе
- Работа с утилитой Blackmagic MultiView Setup
- Работа со SmartView 4K
- Работа со SmartScope Duo 4K
- Подключение к локальной сети
- Изменение сетевых настроек
- Индикация состояния
- Регулировка угла обзора
- Информация для разработчиков
- Помощь
- Соблюдение нормативных требований и правила безопасности
- Гарантия
- Operazioni preliminari
- Utilizzare Blackmagic SmartView Setup
- Utilizzare SmartView 4K
- Utilizzare SmartScope Duo 4K
- Collegarsi ad una rete
- Regolare le impostazioni di rete
- Utilizzare la funzione tally
- Ottimizzare l’angolo di visuale
- Informazioni per gli sviluppatori (English)
- Assistenza
- Normative e sicurezza
- Garanzia
- Instruções Preliminares
- Usar Blackmagic SmartView Setup
- Usar SmartView 4K
- Usar SmartScope Duo 4K
- Conectar a uma Rede
- Ajustar Configurações de Rede
- Usar Sinalização
- Otimizar o Ângulo de Visualização
- Informações para Desenvolvedores
- Ajuda
- Informações Regulatórias e de Segurança
- Garantia
- Başlarken
- Blackmagic SmartView Setup Yazılımının Kullanımı
- SmartView 4K’nın Kullanımı
- SmartScope Duo 4K Kullanımı
- Bir Ağa Bağlanırken
- Ağ Ayarlarının Değiştirilmesi
- Tally Özelliğinin Kullanılması
- İzleme Açısının Optimize Edilmesi
- Yazılım Geliştirici Bilgileri
- Yardım
- Düzenleyici Bildirim ve Güvenlik Bilgileri
- Garanti
Optimizing the Viewing Angle
If SmartView Duo, SmartView HD or SmartScope monitors are to be installed high up in an
equipment rack, you may wish to physically invert the LCDs for the optimum viewing angle.
The images on the LCDs will automatically flip to the correct orientation when they sense an
inversion. A number 02 size pozidriv screwdriver is required to disconnect and reconnect the
faceplate from its rear assembly. This is a simple procedure and does not involve opening the
rear assembly.
The following procedure describes how to invert the unit while keeping the Blackmagic Design
logo in the correct orientation on the faceplate. A number 02 size pozidriv screwdriver
is required.
1 Remove the screws from the top, bottom, left and right sides of the
faceplate. SmartView Duo and SmartScope Duo 4K have 10 screws and
SmartView HD has 18 screws.
2 Lift the front faceplate away from the rear assembly as illustrated.
3 Invert the rear assembly.
4 Reinstate the faceplate on the inverted rear assembly.
5 Reinstate the screws in the chassis.
Your SmartView or SmartScope is now ready to be installed high up in a rack. Once bolted into
a rack, SmartView will continue to display the optimum viewing angle even if bumped, as there
are no external knobs or adjustments to mishandle or to come loose.
SmartView Duo and SmartScope Duo 4K
Tally Pin Connections
Pin Function
1 Monitor 1 Red
2 Monitor 1 Green
3 Monitor 1 Blue
4 Ground
5 Ground
6 Ground
7 Monitor 2 Red
8 Monitor 2 Green
9 Monitor 2 Blue
SmartView HD and SmartView 4K
Tally Pin Connections
Pin Function
1 Red
2 Green
3 Blue
4 Ground
5 4 3 2 1
9 8 7 6
SmartView Tally-Port
28Optimizing the Viewing Angle