ID:CORE STEREO 10 V2, ID:CORE STEREO 20 V2, ID:CORE STEREO 40 V2 Owner’s Manual Designed and Engineered by Blackstar Amplification UK
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. USA / Canada 2. Keep these instructions. 7. Do not block any ventilation openings. 8. Install in accordance with the manufacturer’s instructions. 9. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 10.
English Warning! Important safety information! READ THE FOLLOWING INFORMATION INSTRUCTIONS FOR FUTURE REFERENCE! CAREFULLY. SAVE ALL Follow all warnings and instructions marked on the product! Danger! High internal operating voltages. Do not open the equipment case. There are no user serviceable parts in this equipment. Refer all servicing to qualified service personnel. Clean only with a dry cloth.
The U.S. Government's Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures: Sound Level dBA, Slow Response 8 90 6 92 4 95 3 97 2 100 1½ 102 1 105 ½ 110 ¼ or less 115 English Duration Per Day In Hours According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss.
English Introduction Thank you for purchasing this Blackstar ID:CORE amplifier. Like all our products, this amp is the result of countless hours of painstaking Research and Development by our world-class design team. Based in Northampton (UK), the Blackstar team are all experienced musicians themselves and the sole aim of the development process is to provide guitarists with products which are the ultimate tools for self-expression.
Features English Since 2007, Blackstar has led the way in the innovation of guitar amplification. ID:CORE represents the culmination years of technical Research and Development. These amps have an intuitive control set like a traditional amp, but have the versatility of programmability. The unique controls allow you, the guitarist, to custom design your own sound. The Voice control has six different settings – Clean Warm, Clean Bright, Crunch, Super Crunch, OD 1, OD 2.
English Factory Reset The default factory patches and settings can be restored to your amplifier at any time. Simply hold down the MOD, DLY and REV switches simultaneously, whilst switching on the amplifier. The voice LED will count down to indicate that a factory reset is imminent. If any of the MOD, DLY and REV switches are released before the Voice LEDs have switched off, then the operation is cancelled and the amplifier will remain unaffected.
Front Panel English By using the unique Voice control and the patented ISF, ID:CORE amplifiers allow unparalleled flexibility and ease of use, enabling you to design the sound in your head and deliver it at home, in the studio or in rehearsal. 1. Input Plug your guitar in here. Always use a good quality screened guitar lead. 2. Voice The Voice control changes the preamp voicing, ranging from ultra clean to extremely overdriven.
English This setting is saved when you store a patch. 8. REV (Reverb) Press this switch to turn the stereo reverb effect on, off, or focus the effect for editing. This setting is saved when you store a patch.
. Tap Once set, the Tap LED will flash in time with the set rate of the currently ‘focused’ effect. English The Tap switch is used to set the rate/time of the current ‘focused’ effect. The time between each press of the tap button defines the rate set.
English 14. Manual Press this switch to toggle between Patch and Manual Mode. When the amplifier is in Manual Mode, the sound will reflect the current physical position of the knobs. This is applicable to the Voice, Gain, Volume and ISF knobs. Any effects that are active when switching to Manual Mode will be turned off.
15. Footcontroller (ID:CORE STEREO 20, 40 only) FS-11 Switch 1 Switch 2 Default Mode Toggles between 2 patches, selectable via INSIDER Toggles all saved patch effects on/off Alternative Mode Patch down Patch up English Connect a Blackstar FS-11 footcontroller (not supplied) to control your ID:CORE in one of the following modes: In Alternative Mode (selected via INSIDER) patches will cycle on a ʻloopʼ. e.g switching up from OD2 will move to Clean Warm.
English 18. Recall Indicator The Recall Indicator shows if there is a mismatch between the current value of a parameter within the amplifier and the corresponding physical front panel control. For example, when you change to a different patch the controls on the front panel may not always reflect the setting you are hearing. To prevent unexpected level jumps in the control you are adjusting, the front panel knobs will have no effect on the sound until the knob reaches the current parameter value.
USB Audio English Standard audio drivers are used to connect the amplifier to a PC or Mac. No specific drivers are required. For a guide on low-latency USB recording visit: www.blackstaramps.com/usbrecording NOTE: Always connect the amplifier via a main USB port, often found on the rear of the computer. The amplifier will appear as an audio capture device within recording software.
English Reamping The amplifier can be switched into Reamping Mode via the Blackstar INSIDER software. This is a non-storable setting and will be switched off either when the USB cable is removed, or when the amplifier power is switched off. When activated, Reamping Mode allows the amplifier to accept a pre-recorded, dry guitar signal via USB and return a fully processed audio signal. This return signal can then be captured using recording software on the connected PC or Mac.
Firmware Update Firmware updates are initiated via the Blackstar INSIDER software. A new version of the Blackstar INSIDER software will be released whenever an update is available. Important note: Always connect the amplifier to a main USB port (usually found on the on the rear of your PC or Mac) when updating the firmware. Never use a front mounted USB port, USB hub or a USB extension cable. Doing so may result in a failed update, which could cause your amplifier to become unresponsive.
Technical Specification ID:CORE STEREO 10 V2 Power: 2 x 5 Watts (Stereo 10 Watts) Weight (kg): 3.7 Dimensions (mm): 340(W) x 265(H) x 185(D) ID:CORE STEREO 20 V2 Power: 2 x 10 Watts (Stereo 20 Watts) Weight (kg): 5.2 Dimensions (mm): 375(W) x 292(H) x 185(D) Footcontroller (not supplied): FS-11 footcontroller ID:CORE STEREO 40 V2 Power: 2 x 20 (Stereo 40 Watts) Weight (kg): 6.
Français Cet appareil doit être utilisé dans un environnement bien ventilé et ne doit jamais être mis sous tension si l'endroit est confiné.
Français La loi américaine sur la santé et la sécurité du travail indique la durée d'exposition autorisée à différents niveaux sonores: 8 90 6 92 4 95 3 97 2 100 1½ 102 1 105 ½ 110 ¼ or less 115 Tous les produits électriques et électroniques doivent être jetés séparément, dans le flux de déchets municipaux, dans les lieux de collecte désignés par le gouvernement ou les autorités locales.
Merci d’avoir acheté cet amplificateur Blackstar ID:Core. Comme tous nos produits, cet amplificateur est le résultat d’innombrables heures de recherche et développement minutieux par notre équipe de conception de classe mondiale. Basée à Northampton (Royaume-Uni), l’équipe Blackstar est composée de musiciens chevronnés et l’unique objectif du processus de développement est de fournir aux guitaristes les outils ultimes pour s’exprimer.
Français Caractéristiques Depuis son lancement en 2007, Blackstar a ouvert la voie à l'innovation dans l'amplification guitare. ID:Core représente l‘aboutissement d’années de recherches et de développement. Ces amplis possèdent un contrôle intuitif comme un ampli traditionnel, mais avec la polyvalence de programmabilité en plus. Les contrôles uniques vous permettent, le guitariste, de concevoir sur mesure votre propre son.
Les patches et réglages d’origine par défaut peuvent être à tout moment restaurés dans votre amplificateur. Maintenez simplement pressés simultanément les boutons MOD, DLY et REV, pendant que vous allumez l’amplificateur. Les LEDs de la commande Voice s’éteindront successivement pour indiquer l’imminence de la réinitialisation d’usine.
Français Face Avant 1. Input Branchez ici votre guitare. Utilisez toujours un cordon blindé de bonne qualité pour guitare. 2. Voice La commande Voice change la tonalité de préampli, en allant du son ultra-clair à la saturation extrême.
6. MOD (Modulation) 7. DLY (Delay) Français Pressez ce commutateur afin de mettre l’effet de modulation en/hors service ou de le choisir pour l'éditer. Ce réglage est sauvegardé quand vous mémorisez un patch. Pressez ce commutateur afin de mettre l’effet delay (retard) en/hors service ou de le choisir pour l'éditer. Ce réglage est sauvegardé quand vous mémorisez un patch. 8. REV (Reverb) Pressez ce commutateur afin de mettre l’effet reverb en/hors service ou de le choisir pour l'éditer.
Français 10. Niveau d’effet (Level) Modifie un paramètre d’effet. Pour les effets de modulation et de retard (delay), tourner la commande Level en maintenant enfoncé le commutateur Tap (11) modifie la cadence/ durée de l’effet. Le effet tableau ci-dessous montre les paramètres modifiables. Ce réglage est sauvegardé quand vous mémorisez un patch. 11. Tap Le commutateur Tap sert à régler la cadence/durée de l’effet actuellement choisi pour l’édition.
13. USB Voir la section Audio USB pour plus d’informations. Français Branchez ici un câble USB pour relier l’amplificateur à un PC sous Windows ou à un Mac. Le logiciel Insider de Blackstar peut être téléchargé depuis cette adresse: www.blackstarinsider.co.uk et offre une foule de fonctions. NOTE: l’amplificateur apparaîtra dans le logiciel d’enregistrement d’un ordinateur comme un périphérique de capture audio. 14. Manual Pressez ce commutateur pour alterner entre le mode manuel et le patch actuel.
Français Les autres LED de la face avant seront éteintes en mode accordeur. Presser n’importe quel commutateur de la face avant vous fera quitter le mode accordeur. 15.
18. Indicateur Recall Français L’indicateur Recall signale une disparité entre la valeur actuelle d’un paramètre dans l’amplificateur et la commande physique correspondante en façade. Par exemple, quand vous changez de patch, les commandes de la face avant peuvent ne plus refléter les réglages que vous entendez.
Français Audio USB Des pilotes audio standards sont utilisés pour connecter l’amplificateur à un PC ou à un Mac, aucun pilote spécifique n’est nécessaire. Pour un guide sur la faible latence USB visitez: www.blackstaramps.com/usbrecording NOTE : Toujours connecter l'amplificateur sur un port USB principal, souvent à l'arrière de l'ordinateur. L’amplificateur apparaitra comme périphérique de capture audio dans le logiciel d’enregistrement.
Ré-amplification Français L’amplificateur peut être commuté en mode de ré-amplification via INSIDER. C’est un réglage non programmable qui sera désactivé soit lorsque le câble USB sera retiré soit lorsque l’amplificateur sera éteint. Quand il est activé, le mode de ré-amplification permet à l’amplificateur d’accepter un signal de guitare sec préenregistré via USB et de renvoyer un signal audio entièrement traité.
Français de firmware. Si l’amplificateur est coupé durant une mise à jour, les commandes ne répondront pas lorsqu’il sera rallumé et l’amplificateur ne produira aucun son. Les LED clignoteront pour indiquer que l’amplificateur ne contient pas de firmware exploitable. Si vous rencontrez des problèmes avec la mise à jour de la nouvelle version, l’ampli peut être forcé à s’allumer en mode Mise à Jour.
¡AVISO! Español Importante Información de seguridad LEA LA SIGUIENTE INFORMACIÓN DETENIDAMENTE Y CONSERVE LAS INSTRUCCIONES PARA FUTURAS CONSULTAS. SIGA TODOS LOS AVISOS E INSTRUCCIONES MARCADAS EN LOS PRODUCTOS. ¡PELIGRO! Alto voltaje interno. No abra la tapa del equipo. No hay partes utilizables para otros fines en este equipo. Remita cualquier anomalía al servicio técnico cualificado. Utilice trapos secos para su limpieza.
Reemplace siempre los fusibles dañados por otros de características idénticas. Español Nunca desconecte el protector de la toma de tierra. La potencia de sonido de los altavoces cuando los niveles son altos puede causar daño permanente. Se debe evitar por tanto la exposición directa a loa altavoces cuando estos estén operando a un alto nivel. Usa siempre protectores auditivos ante una exposición prolongada.
Introducción Español Gracias por comprar este amplificador Blackstar ID:Core. Como todos nuestros productos, este amplificador es el resultado de incontables horas de meticulosa Investigación y Desarrollo por parte de nuestro prestigioso equipo de diseño.
Características Español Desde 2007, Blackstar ha liderado el camino de la innovación en amplificadores de guitarra. ID:Core representa la culminación de años de Investigación y Desarrollo. Este amplificador tiene un intuitivo panel de control, pero con la versatilidad que ofrece un amplificador programable. Los controles únicos te permiten a ti, el guitarrista, diseñar tu propio sonido. El control Voice tiene seis ajustes diferentes: Clean Warm, Clean Bright, Crunch, Super Crunch, OD 1 y OD 2.
Restablecer ajustes de fábrica Español Los bancos de sonido por defecto se pueden restablecer en cualquier momento. Simplemente mantén pulsados simultáneamente los botones MOD, DLY y REV, mientras enciendes el amplificador. El indicador LED hará una cuenta atrás para indicar que se va a restablecer los ajustes de fábrica.
Español Panel Frontal 1. Input Conecta tu guitarra aquí. Usa siempre un cable apantallado de calidad. 2. Voice El control Voice cambia el carácter previo, desde limpios cristalinos hasta distorsión extrema.
8. REV (Reverb) Español Pulsa este interruptor para conectar o desconectar el efecto reverb, o seleccionarlo para su edición. Este ajuste queda almacenado al guardar un banco de sonido.
11. Tap Español El interruptor Tap se usa para ajustar la frecuencia o tiempo del efecto seleccionado para la actual edición. El tiempo entre pulsaciones del interruptor Tap establece la frecuencia del efecto. Una vez establecido, el LED parpadeará indicando la frecuencia del efecto seleccionado.
Español NOTA: el amplificador aparecerá como “Dispositivo de grabación de audio” en el ordenador. 14. Manual Pulsa este interruptor para cambiar entre modo manual y el banco de sonido actual. Cuando el amplificador está en modo manual, el sonido reflejará la posición física de los controles del panel frontal. Esto es aplicable a los controles Voice, Gain, Volume, ISF. Los efectos que estén activos cuando se cambia el modo manual se desactivaran.
15.
El indicador Recall se activa para Gain, Volume e ISF. Español Cuando el afinador está activo el indicador Recall parpadeará continuadamente. Panel Trasero 1. DC Input El cable de alimentación desmontable subministrado se conecta aquí. Asegúrate siempre que el botón de encendido (12) está en OFF antes de conectar el cable. El cable solo debe estar conectado a un enchufe que sea compatible con el voltaje, la fuerza y la frecuencia requerida que se menciona en el panel trasero.
Español La salida de audio de su amplificador al ordenador via USB se hace a través de cuatro canales simultáneos e independientes: Canal 1 : Emulación de Stereo, canal izquierdo — El sonido de guitarra completamente procesado, con emulación de gabinete de altavoz. Contiene el canal izquierdo de los efectos Super Wide Stereo. Canal 2 : Emulación de Stereo, canal derecho — El sonido de guitarra completamente procesado, con emulación de gabinete de altavoz.
Características Avanzadas Español El amplificador ID:Core tiene varias características avanzadas para una mayor profundidad de conocimiento y disfrute del usuario y sacar el mayor partido al amplificador. Estas características no tienen un control propio en el panel frontal del amplificador, pero se tiene acceso a ellos usando el control Tap (11) como una tecla ‘shift’ y otro control.
Español Actualización de Firmware Las actualizaciones de Software se realizaran mediante el software Blackstar Insider. Se lanzará una nueva versión del software siempre que una actualización esté disponible. Nota importante: Siempre conecte el amplificador a un puerto USB principal (normalmente se encuentra detrás del PC o Mac) cuando se actualice el firmware. Nunca use un puerto USB frontal alternativo o montable, o un cable de extensión USB.
Especificaciones Técnicas Español ID:CORE STEREO 10 V2 Potencia: 2 x 5 Watios (Stereo 10 Watios) Peso (kg): 3.7 Dimensiones (mm): 340(W) x 265(H) x 185(D) ID:CORE STEREO 20 V2 Potencia: 2 x 10 Watios (Stereo 20 Watios) Peso (kg): 5.2 Dimensiones (mm): 375(W) x 292(H) x 185(D) Footcontroller (no incluido): FS-11 footcontroller ID:CORE STEREO 40 V2 Power: 2 x 20 Watios (Stereo 40 Watios) Peso (kg): 6.
English ID:CORE STEREO 20 V2 Front Panel Deutsch Français F.
English ID:CORE STEREO 40 V2 Front Panel Deutsch Français F.
130300 M-1 11/16 Blackstar Amplification Ltd, Beckett House, 14 Billing Road, Northampton, NN1 5AW, UK For the latest information go to: www.blackstaramps.com Whilst the information contained herein is correct at the time of publication, due to our policy of constant improvement and development, Blackstar Amplification Ltd reserves the right to alter specifications without prior notice.