Owner`s manual

Program Change Assignment
To change the default assignments and set the amp up to respond to a different set
of Program Changes:
1. The amp must be powered on with either the Standby switch set to on, a jack
in the Input socket, or both.
2. Send the appropriate Program Change message to the amp.
3. Press and hold in the appropriate front panel Channel Select switch for
2 seconds.
The corresponding channel will be selected and its LED will flash three times in quick
succession to indicate it has been assigned to the last received Program Change.
The amplifier will now remember the selection. Repeat the operation until all your
Program Changes have the desired amp channel assigned to them.
MIDI Receive Channel Selection
As mentioned previously, the default mode is set to OMNI and the amplifier will
respond to MIDI Program Changes on all MIDI channels. You may wish to set the
amplifier to respond to Program Changes on just a single MIDI channel. The Series
One can be set to respond in this way for any of the first seven MIDI channels as
follows:
1. The unit must be in standby (Power (34) on and Standby (33) off), and no lead
connected to the Input jack.
2. Simultaneously press and hold the Clean (3) and OD1 (17) Select switches.
3. After 2 seconds the LED for OD2 (20) will begin to flash continuously (2 flashes
per second) to indicate that the unit is in MIDI Receive Channel Program Mode.
4. Release the Clean (3) and OD1 (17) Select switches and select the required MIDI
channel by using the Channel Select switches as shown in the table below:
The corresponding Channel Select LEDs will illuminate to show the selection and
each press of the Channel Select switches will toggle the state of its associated
LED.
5. To store the desired selection press the OD2 (21) Select switch. The OD2 (20)
Select LED will flash quickly four times when the operation is complete. The unit
will then revert to normal operation, and will respond only to Program Changes
on the newly selected MIDI Channel.
English
15
MIDI Channel Switching
The Series One offers the ability to control channel selection via MIDI Program
Change messages and interfacing with most MIDI controllers is a straight forward
process. The Series One can be placed in a MIDI chain allowing you to
simultaneously select a channel on the amplifier and change the patch on a MIDI
effects processor connected to the effects loop. There are 128 available Program
Changes, giving you the possibility to access a vast number of tonal combinations.
To set-up MIDI channel switching, simply connect the MIDI controller’s MIDI Out
socket to the MIDI In socket on the rear of the amplifier. The controller should be set
to transmit Program Change messages (this is usually the case). From new, a Series
One amplifier is set to OMNI mode and responds to Program Change messages on
all MIDI channels. Changing ‘patches’ on the controller will change the selected
channel on the amp. The default settings for each Program Change number are
shown in the table below:
English
14
1 CLEAN
2 CRUNCH
3 OVERDRIVE 1
4 OVERDRIVE 2
5 CLEAN
6 CRUNCH
7 OVERDRIVE 1
8 OVERDRIVE 2
9 CLEAN
10 CRUNCH
11 OVERDRIVE 1
12 OVERDRIVE 2
13 CLEAN
14 CRUNCH
15 OVERDRIVE 1
16 OVERDRIVE 2
17 CLEAN
18 CRUNCH
19 OVERDRIVE 1
20 OVERDRIVE 2
21 CLEAN
22 CRUNCH
23 OVERDRIVE 1
24 OVERDRIVE 2
25 CLEAN
26 CRUNCH
27 OVERDRIVE 1
28 OVERDRIVE 2
29 CLEAN
30 CRUNCH
31 OVERDRIVE 1
32 OVERDRIVE 2
33 CLEAN
34 CRUNCH
35 OVERDRIVE 1
36 OVERDRIVE 2
37 CLEAN
38 CRUNCH
39 OVERDRIVE 1
40 OVERDRIVE 2
41 CLEAN
42 CRUNCH
43 OVERDRIVE 1
44 OVERDRIVE 2
45 CLEAN
46 CRUNCH
47 OVERDRIVE 1
48 OVERDRIVE 2
49 CLEAN
50 CRUNCH
51 OVERDRIVE 1
52 OVERDRIVE 2
53 CLEAN
54 CRUNCH
55 OVERDRIVE 1
56 OVERDRIVE 2
57 CLEAN
58 CRUNCH
59 OVERDRIVE 1
60 OVERDRIVE 2
61 CLEAN
62 CRUNCH
63 OVERDRIVE 1
64 OVERDRIVE 2
65 CLEAN
66 CRUNCH
67 OVERDRIVE 1
68 OVERDRIVE 2
69 CLEAN
70 CRUNCH
71 OVERDRIVE 1
72 OVERDRIVE 2
73 CLEAN
74 CRUNCH
75 OVERDRIVE 1
76 OVERDRIVE 2
77 CLEAN
78 CRUNCH
79 OVERDRIVE 1
80 OVERDRIVE 2
81 CLEAN
82 CRUNCH
83 OVERDRIVE 1
84 OVERDRIVE 2
85 CLEAN
86 CRUNCH
87 OVERDRIVE 1
88 OVERDRIVE 2
89 CLEAN
90 CRUNCH
91 OVERDRIVE 1
92 OVERDRIVE 2
93 CLEAN
94 CRUNCH
95 OVERDRIVE 1
96 OVERDRIVE 2
97 CLEAN
98 CRUNCH
99 OVERDRIVE 1
100 OVERDRIVE 2
101 CLEAN
102 CRUNCH
103 OVERDRIVE 1
104 OVERDRIVE 2
105 CLEAN
106 CRUNCH
107 OVERDRIVE 1
108 OVERDRIVE 2
109 CLEAN
110 CRUNCH
111 OVERDRIVE 1
112 OVERDRIVE 2
113 CLEAN
114 CRUNCH
115 OVERDRIVE 1
116 OVERDRIVE 2
117 CLEAN
118 CRUNCH
119 OVERDRIVE 1
120 OVERDRIVE 2
121 CLEAN
122 CRUNCH
123 OVERDRIVE 1
124 OVERDRIVE 2
125 CLEAN
126 CRUNCH
127 OVERDRIVE 1
128 OVERDRIVE 2
Program Channel
Change
Clean Crunch OD1 MIDI CHANNEL
OFF OFF OFF OMNI
ON OFF OFF 1
OFF ON OFF 2
ON ON OFF 3
OFF OFF ON 4
ON OFF ON 5
OFF ON ON 6
ON ON ON 7