Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com or www.towerhobbies.com and click on the support or resources tab for this product.
Box Contents: • • • • • Blade 330 S 3S 11.1V 2200mAh 30C IC3 Smart Li-Po Battery (RTF Only) DC Li-Po Balancing Smart Charger (RTF Only) Spektrum DXe Transmitter (RTF Only) 4 AA Batteries (RTF Only) Table of Contents First Flight Preparation ......................................................................................4 Flying Checklist.................................................................................................4 Charging Warnings ................................................
First Flight Preparation Flying Checklist • • • • • • • ❏ ❏ ❏ ❏ ❏ ❏ ❏ Remove and inspect contents Begin charging the flight battery Install the flight battery in the helicopter (once it has been fully charged) Program your computer transmitter Bind your transmitter (BNF only) Familiarize yourself with the controls Find a suitable area for flying Charging Warnings Always turn the transmitter on first Plug the flight battery into the lead from the ESC Allow the ESC to initialize and arm properly Fly the mode
Installing the DXe Transmitter Batteries (RTF) The LED indicator flashes and the transmitter beeps progressively faster as the battery voltage drops. Replace the transmitter batteries when the transmitter begins to beep. CAUTION: NEVER remove the transmitter batteries while the model is powered on. Loss of model control, damage or injury may occur. CAUTION: If using rechargeable batteries, charge only rechargeable batteries.
DX6G2, DX6e, DX7G2, DX8G2, DX9, DX18, DX20, iX12, iX20 SYSTEM SETUP FUNCTION LIST Model Type Swash Type HELI Normal F-Mode Setup Switch 1 Switch 2 Hold Switch Switch B Inhibit Switch H 1 0 Channel Assign Channel Input Config 1 Throttle 2 Aileron 3 Elevator 4 Rudder 5 Gear F Mode 6 Collective 7 AUX 2* Switch I Servo Setup Chan THR AIL ELE RUD GER D/R & Expo Chan Sw (F) Pos 0 AILE 1 2 0 ELEV 1 2 0 Rudd 1 2 Travel 100/100 100/100 100/100 100/100 100/100 D/R 100/100 85/85 85/85 100/100 85/85 85/85 100/1
Installing the Flight Battery 1. 2. 3. 4. 5. 6. 7. 8. Lower the throttle. Power on the transmitter. Center the throttle trim. To allow the ESC to arm and to keep rotors from initiating at startup, turn on throttle hold and normal flight mode before connecting the flight battery. Attach hook material to the helicopter frame and loop material to the battery. Install the flight battery on the helicopter frame. Secure the flight battery with a hook and loop strap. Connect the battery cable to the ESC.
Control Tests CAUTION: You must complete the Tail Rotor and Cyclic tests prior to every flight. Failure to complete the tests and ensuring the sensor corrects in the proper direction can cause the helicopter to crash, resulting in property damage and injury. Tail Rotor 1. Power on the transmitter. 2. Turn TH HOLD ON and put the transmitter in normal mode. 3. Connect the flight battery to the ESC. 4. Move the rudder stick to the right. The pitch slider on the tail shaft should move toward the tail case.
Motor Test Place the helicopter outdoors on a clean, flat and level surface (concrete or asphalt) free of obstructions. Always stay clear of moving rotor blades. 1. The motor beeps twice when the helicopter’s ESC arms properly. Before continuing, confirm TH HOLD is ON. WARNING: Stay at least 30 feet (10 meters) away from the helicopter when the motor is running. Do not attempt to fly the helicopter at this time. 3. Ensure the throttle is lowered completely.
Pre-Flight Checklist ❏ Check all screws and ensure that they are tight ❏ Check gears and make sure no teeth are missing ❏ Check belt tension and ensure that it is not too tight or too loose ❏ Do a complete control test ❏ Check main and tail blades to ensure they are not damaged ❏ Verify the receiver sensor is correcting in the proper directions ❏ Check all links and make sure they move freely but do not pop off easily ❏ Check that servos are functioning properly ❏ Check that flight battery and transm
Post-Flight Inspections and Maintenance Ball Links Make sure the plastic ball link holds the control ball, but is not tight (binding) on the ball. When a link is too loose on the ball, it can separate from the ball during flight and cause a crash. Replace worn ball links before they fail. Cleaning Make sure the battery is not connected before cleaning. Remove dust and debris with a soft brush or a dry lint free cloth. Bearings Replace bearings when they become damaged.
Advanced Tuning (Non-Forward Programming) While watching the swashplate servos, apply fore or aft cyclic and release. One of the servos will jump, indicating the selected servo. Apply fore or aft cyclic and release until the servo that needs to be adjusted is selected. Applies to Spektrum transmitters not capable of forward programing including DX6i, DX6e, DX7s DX8, and DX8e Your Blade 330 S was setup at the factory and test flown.
Troubleshooting Guide Problem Possible Cause Solution Low flight battery or transmitter battery voltage receiver is not in bind mode Fully charge or replace the flight battery and/or transmitter batteries Make sure the bind plug is connected to the receiver BND/DAT port Helicopter will not bind Power on the transmitter while holding the Trainer/Bind switch. Hold the Trainer/ Transmitter is not in bind mode to the transmitter Bind switch until binding is complete (during binding) Power off the transmitter.
Limited Warranty What this Warranty Covers Inspection or Services If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton.
Warranty and Service Contact Information Country of Purchase Horizon Hobby Horizon Service Center (Repairs and Repair Requests) Horizon Product Support (Product Technical Assistance) United States of America Sales European Union Horizon Technischer Service Sales: Horizon Hobby GmbH Contact Information servicecenter.horizonhobby.com/RequestForm/ productsupport@horizonhobby.com 877-504-0233 websales@horizonhobby.com 800-338-4639 service@horizonhobby.
Exploded View / Explosionszeichnung / Vue Éclatée / Vista Esplosa 25 20 8 11 22 25 12 12 11 11 9 25 26 20 13 9 12 20 26 11 20 10 22 10 15 25 54 32 14 13 14 27 21 28 16 60 52 52 52 59 51 20 60 57 58 18 53 23 58 46 55 56 18 52 58 49 55 18 57 58 58 58 51 18 47 48 23 57 59 6 50 45 IT 58
32 15 29 33 64 63 5 36 32 24 15 34 41 44 32 32 63 34 24 15 65 5 35 19 33 32 43 70 1 37 2 40 5 32 33 42 67 15 32 64 63 40 66 36 39 17 59 IT
Parts List / Ersatzteile / Pièces de Rechange / Pezzi di Ricambio # Part # 1 BLH1901 2 BLH1902 3 SPMSP1040 4 SPMSP1041 5 SPMSH3050 6 SPMSH3060 7 SPMSP2052 8 BLH4301 9 BLH4303 10 BLH4315 11 BLH4317 12 BLH4321 13 BLH4322 14 BLH4331 15 BLH4338 16 BLH4347 17 BLH4006 18 EFLH1115 19 BLH1603 20 BLH1605 21 BLH1607 22 BLH1608 23 BLH1612 24 BLH1613 25 BLH1616 26 BLH1620 27 BLH1632 28 BLH1633 29 BLH1634 30 BLH1635 31 BLH1636 32 BLH1637 33 BLH4005 34 BLH1640 35 BLH1641 36 BLH1642 IT English Deutsch Blade 450/300x/
# Part # 42 BLH1653 Français Set de fixations moteur en aluminium : B450 3D/X, B400 Sangles crochet et boucle pour ruban Hook & Loop Battery Strap: B450 Akku-Klettverschlussband B450 3D/X, adhésif d’accu : B450 3D/X, B400 (non 3D/X, B400 (not shown) B400 (nicht gezeigt) représenté) Landing Gear Set: B450 3D/X Fahrwerk-Set: B450 3D/X Set de train d’atterrissage : B450 3D/X One-Way Bearing Shaft and Shim Set Einweglagerwelle und Unterlagss- Axe de roue libre et set de rondelles : Set: B450 3D/X, B400 cheib
Optional Parts / Optionale Bauteile / Pièces Optionnelles / Pezzi Opzionali Part # BLH1903 BLH1904 BLH1905 BLH1906 BLH1907 BLH4302 BLH4317A BLH4331A BLH1633A BLH1634A BLH1645B BLH1654A BLH1655A BLH1657C BLH1658A BLH1661A BLH1662A BLH1663A BLH1665A BLH1667A BLH1668A BLH1670A BLH1671B BLH1671C BLH1672B BLH1672C BLH1676A BLH1679A BLH1690A IT English Deutsch Blade 450/300x/300CFX: Helical Pinion 11T B450/300X/CFX Ritzel 11 Z schrägverz.
Part # English Aluminum 450 Flybarless Conversion Set: BLH4399 B450 3D Tail Rotor Blade Set, Orange: B450 3D/X, BLH1671OR B400 Tail Rotor Blade Set, Yellow: B450 3D/X, BLH1671YE B400 Tail Rotor Blade Set, Green: B450 3D/X, BLH1671GR B400 BLH1699 450 Carrying Case Deutsch Aluminium-450 FlybarlessUmrüstungs-Set: B450 3D Heckrotorblatt-Set, orange: B450 3D/X, B400 Heckrotorblatt-Set, gelb: B450 3D/X, B400 Heckrotorblatt-Set, grün: B450 3D/X, B400 450 Tragekoffer BLH4006 Optionales Glasfaser-Kabinendach: 33
©2019 Horizon Hobby, LLC. Blade, the Blade logo, SAFE, The SAFE logo, DSM2, DSMX, BNF, the BNF logo, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. All other trademarks, service marks or logos are property of their respective owners. US 9,930,567. US 8,672,726. D774,933. Other patents pending.
