User Manual

6
EN
Throttle Curve
Sw (B) Pos Pt 1 Pt 2 Pt 3 Pt 4 Pt 5
N 0 65 65 65 65
17070707070
28080808080
Hold 0 0 0 0 0
Pitch Curve
Sw (B) Pos Pt 1 Pt 2 Pt 3 Pt 4 Pt 5
N 25 37 50 75 100
1 0 25 50 75 100
2 0 25 50 75 100
HOLD 25 37 50 75 100
Chan Travel Reverse
THR 100/100 Normal
AIL 100/100 Normal
ELE 100/100 Normal
RUD 100/100 Normal
GER 100/100 Normal
Chan Travel Reverse
PIT 100/100 Normal
AX2* 100/100 Normal
AX3* 100/100 Normal
AX4* 100/100 Normal
Servo Setup
FUNCTION LIST
DX6G2, DX6e, DX7G2, DX8G2, DX9, DX18, DX20, iX12, iX20
Timer
Mode Count Down
Time 4:00
Start Throttle Out
Over 25%
One Time Inhibit
Model Type HELI
Swash Type Normal
F-Mode Setup
Switch 1 Switch B
Switch 2 Inhibit
Hold Switch Switch H
0
1
Channel Assign
Channel Input Con g
1 Throttle
2 Aileron
3 Elevator
4 Rudder
5 Gear F Mode
6 Collective
7 AUX 2* Switch I
Frame Rate
11ms*
DSMX
SYSTEM SETUP
* Function is not available
on all transmitters
D/R & Expo
Chan Sw (F) Pos D/R Expo
AILE
0 100/100 0
1 85/85 0
2 85/85 0
ELEV
0 100/100 0
1 85/85 0
2 85/85 0
Rudd
0 100/100 0
1 85/85 0
2 85/85 0
SMART Throttle (BNF Only)
The new line of Spektrum ESCs feature a telemetry function called SMART Throttle.
SMART Throttle technology combines the throttle signal with telemetry data from
the ESC on one normal three wire servo connector.
SMART Throttle ESCs can send current, voltage, ESC temp, and mAh consumed.
They can also pass along battery data from compatible Spektrum SMART batter-
ies. SMART Throttle telemetry data shows up on your transmitter like any other
telemetry sensor.
For SMART Throttle to function you must have a SMART Throttle ESC paired with
a SMART Throttle telemetry receiver, and a Spektrum DSMX transmitter with
telemetry. Only certain Spektrum products include SMART technology compatibil-
ity, check your receiver and ESC manual for more information. An update for your
transmitter may be required for SMART features.
(See www.spektrumrc.com to register and update your transmitter.)
To activate SMART Telemetry:
1. Keep the vehicle powered on after binding the transmitter to the receiver
2. Scroll to the Telemetry screen
3. Scroll to Settings
4. Select Auto Confi g
To activate Speed infomation using SMART Telemetry:
5. After doing the initial SMART telemetry confi guration keep the vehicle powered
on
6. Scroll to the Telemetry screen
7. Scroll to SMART ESC and double select
8. Scroll down to NEXT
9. Enter the values for the magnetic pole count of the motor and the gear ratio
(motor and gear ratio information can be found in the manual for your vehicle)
When the radio is on and connected to a receiver sending SMART Data, the SMART
Logo will appear under the battery logo on the home page and a signal bar will
appear in the top left corner of the screen. Scrolling down, past the servo monitor,
the SMART screens will appear. Select either ESC, battery, or both for display to
suit your preference.