User Manual

6
EN
Servo Setup
FUNCTION LISTSYSTEM SETUP
DX7s
D/R & Expo
Chan
Switch Pos (FLAP) D/R Expo*
AILE
0 100/100 0
1 100/100 0
2 75/75 0
ELEV
0 100/100 0
1 100/100 0
2 75/75 0
RUDD
0 100/100 0
1 100/100 0
2 75/75 0
Chan Travel Reverse
THR 100/100 Normal
AIL 100/100 Normal
ELE 100/100 Normal
RUD 100/100 Normal
Chan Travel Reverse
GER 100/100 Normal
AX1 100/100 Reverse
AX2 100/100 Normal
Model Type ACRO
SW Select
Trainer Aux 1
Flap Gear
All Others INH
* Use of "Expo" is not necessary for successful fl ight. The pilot may adjust this setting to tailor the sensitivity around
neutral if desired.
D/R & Expo
Chan Sw Pos D/R Expo*
AILE
0 100 INH
1 75 INH
ELEV
0 100 INH
1 75 INH
RUDD
0 100 INH
1 75 INH
Timer
Down Timer 5:00
Switch THR CUT
ADJUST LISTSETUP LIST
DX6i
TRAVEL ADJ
Channel Travel
THRO 100/100
AILE 100/100
ELEV 100/100
RUDD 100/100
GEAR 100/100
FLAP 100/100
REVERSE
Channel Direction
THRO N
AILE N
ELEV N
RUDD N
GEAR R
FLAP N
Modulation Type
AUTO DSMX-ENABLE
D/R COMBI
D/R SW AILE
Model Type Acro
Flight Mode Operation
Gear Sw: Pos 0, Elev D/R Sw: 0 or 1 = Stability Mode (internal quadcopter LED Green)
Gear Sw: Pos 1, Elev D/R Sw: 0 = Stagility Mode (internal quadcopter LED Yellow)
Gear Sw: Pos 1, Elev D/R Sw: 1 = Agility Mode (internal quadcopter LED Red)
Mixing
MIX 1 ACT
GEAR > GEAR ACT
RATE D 0% U –100%
SW
GEAR TRIM – INH
MIX 2
ACT
GEAR > GEAR
ACT
RATE
D 0% U +100%
SW
ELE D/R TRIM – INH
FLAPS
FLAP ELEV
NORM 100 0
LAND
100 0
Camera Control/
Continuous Flip**
Bind / I Button
Press twice rapidly (within 2 seconds) = still photo (rear LEDs blink once)
Press and hold 3 seconds = start/stop video (rear LEDs slowly fl ash while recording)
** If no camera is installed, pressing and holding the Bind button while in FM0 enables
the continuous fl ip feature (see the Flight Mode Selection section for details).
Camera Control/Continuous Flip**
Flap Switch
Set the switch position to 0 for normal. Set the switch to pos 1 until the rear LEDs slowly fl ash, then set it back to 0 to
start recording video. To stop recording, set the switch to pos 1 until the rear LEDs glow solid, then set it back to pos 0.
Quickly cycle the switch from pos 0 to pos 1 and back two times to take a photo.
Always return the fl ap switch to pos 0.
** If no camera is installed, switching the fl ap switch to pos 1 while in FM0 enables
the continuous fl ip feature (see the Flight Mode Selection section for details).
Flight Mode Operation
FLAP Sw: Pos 0 = Stability Mode
Pos 1 = Stagility Mode
Pos 2 = Agility Mode
Timer
Mode Count Down
Time 5:00 Tone
Start Throttle Out
Pos 25%