Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni RTF
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
• Never attempt to dismantle the charger or use a damaged charger. • Always use only rechargeable batteries designed for use with this type of charger. • Always inspect the battery before charging. • Always keep the battery away from any material that could be affected by heat. • Always monitor the charging area and have a fire extinguisher available at all times. • Always end the charging process if the battery becomes hot to the touch or starts to change form (swell) during the charge process.
Box Contents • Blade® Inductrix® Switch Air • 3.
Installing the Transmitter Batteries Replace the transmitter batteries when the power LED flashes and the transmitter beeps. CAUTION: NEVER remove the transmitter batteries while the model is powered on. Loss of model control, damage, or injury may occur. CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to national regulations. CAUTION: If using rechargeable batteries, charge only rechargeable batteries.
Transmitter and Receiver Binding RTF Your RTF transmitter comes prebound to the model. If you need to re-bind, follow the directions below. MLP4DSM Binding Procedure 1. Disconnect the flight battery from the quadcopter. 2. Center all trims on your transmitter. 3. Power off the transmitter and move the throttle stick to the down/off position. 4. Connect the flight battery in the quadcopter. The LED on the control unit flashes after 5 seconds. 5.
LED Codes Equipment LED Color Red Purple Blue Green Amber Flight control LED on White the control board, RGB Green Orange Red Blue Blue Front LEDs White Rear LEDs Red LED Status Solid Solid Solid Solid Solid Solid Blinks for 1 second at power ON Blinks for 1 second at power ON Blinks for 1 second at power ON Blinking rapidly Blinking slowly Blinking rapidly Solid Blinking slowly Blinking slowly Blinking rapidly Solid Blinking slowly Operation Position 2; Quadcopter AS3X mode Position 1; Quadcopter Hor
Understanding the Primary Flight Controls If you are not familiar with the controls of your Inductrix® Switch Air wing and quadcopter, take a few minutes to familiarize yourself with them before attempting your first flight. Quadcopter Operation To selct Quadcopter mode, with the aircraft and transmitter powered on and bound, press both sticks to the outside bottom corners for 3 seconds. Quadcopter Flight Modes Change flight modes by pushing down on the right stick.
Flying the Switch™ Quadcopter Takeoff Increase the throttle until the model is approximately 2 ft. (600mm) off the ground and check the trim so the model flies as desired. Once the trim is adjusted, begin flying the model. Typical flight times for the included battery range from 3 to 4 minutes. Low Voltage Cutoff (LVC) LVC decreases the power to the motors when the battery voltage gets low.
Elevator Left Side View Elevator up Forward Left Side View Elevator down Backward Aileron and Rudder - Right Stick Top View Nose Yaws Left Right Stick to left Rear View Left EN 10
Aileron and Rudder - Right Stick (continued) Top View Nose Yaws Right Right Stick to right Rear View Right 11 EN
Air Mode Operation (Expert mode) Throttle Left Side View Throttle up Climb Left Side View Descend Throttle down Elevator Left Side View Elevator up Forward Left Side View Elevator down Backward Aileron Rear View Aileron left Left Rear View Right Aileron right EN 12
Rudder Top View Nose Yaws Left Rudder left Top View Nose Yaws Right Rudder right Hovercraft Operation The hovercraft base plate (BLH9805) and foam skirt (BLH9806) are not included with this product and are sold separately. Please refer to the manual for the Inductrix Switch (BLH9800) for operation in the two hovercraft modes; single-stick or two-stick mode.
Post-Flight Inspection and Maintenance Checklist √ Cleaning Make sure the battery is not connected before cleaning. Remove dust and debris with a soft brush or a dry, lint-free cloth. Motors Replace the motor when the model will not fly steady or veers off when doing a climb out. Wiring Make sure the wiring does not block moving parts. Replace damaged wiring and loose connectors. Fasteners Propellers Make sure there are no loose screws, other fasteners or connectors.
Exploded View Quadcopter Assembly Air Wing Assembly 3 2 8 9 5 6 1 7 1 4 2 8 1 1 11 4 10 9 Replacement Parts 1 2 3 4 5 6 Part # Description BLH8521 BLH8705 BLH9807 BLH9803 BLH9802 BLH08301 Pro Motor Set (4) Propeller Set, White (4) Canopy, Red Duct Set (2) Control Board Replacement Wing 7 8 9 10 Part # Description BLH9804 BLH9801 EFLB1501S25 EFLC1008 Main Frame Propeller Set (4) 3.7V 150mAh 1S 25C LiPo 1S USB LiPo charger, 350mAh Blade MLP4DSM 4CH transmitter, 2.
Limited Warranty What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the "Product") will be free from defects in materials and workmanship at the date of purchase.
Warranty and Service Contact Information Country of Purchase United States of America Horizon Hobby Contact Information Horizon Service Center (Repairs and Repair Requests) Horizon Technischer Service servicecenter.horizonhobby.com/ RequestForm/ productsupport@horizonhobby.com 877-504-0233 websales@horizonhobby.com 800-338-4639 service@horizonhobby.
Compliance Information for the European Union EU Compliance Statement: BLH8300: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the RED and EMC Directives. BLH8380: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the RED and EMC Directives. A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.
©2019 Horizon Hobby, LLC. Blade, the Blade logo, Inductrix, BNF and Bind-N-Fly logo, E-flite, SAFE, the SAFE logo, DSM, DSM2, DSMX, ModelMatch and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. All other trademarks, service marks or logos are property of their respective owners. Created 12/18 60431.
