Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
Table of Contents Using the Micro Camera.................................................11 Post-Flight Inspection and Maintenance Checklist ..........11 Replacing the Propellers ................................................12 Drift Calibration..............................................................12 Troubleshooting Guide ...................................................13 Exploded View ...............................................................14 Parts Listings .............................
First Flight Preparation Flying Checklist • • • • • ❏ Always turn the transmitter on first ❏ Plug the flight battery into the lead from the 3-in-1 ESC ❏ Allow the receiver and ESC to initialize and arm ❏ Fly the model ❏ Land the model ❏ Unplug the flight battery from the 3-in-1 ESC ❏ Always turn the transmitter off last Remove and inspect contents Begin charging the flight battery Program your computer transmitter Familiarize yourself with the controls Install the flight battery in the quadcopter (once it ha
Transmitter Setup If you are programming your DXe using the PC or mobile app, make sure the "Transmitter Channels" value is set to the default of 7. If for any reason this value is changed to 9, the Inductrix will bind to the DXe, but will not respond to control inputs. If your DXe was included in another Blade Ready To Fly (RTF) helicopter, the transmitter software will have to be updated using the appropriate programming cable and either the PC or mobile app available at www.spektrumrc.com.
DX6i SETUP LIST ADJUST LIST Model Type REVERSE Channel THRO AILE ELEV RUDD GEAR FLAP Acro Direction N N N N R N Modulation Type AUTO DSMX-ENABLE D/R COMBI D/R SW TRAVEL ADJ Channel THRO AILE ELEV RUDD GEAR FLAP Travel 100/100 100/100 100/100 100/100 100/100 100/100 D/R & Expo Chan Sw Pos 0 AILE 1 0 ELEV 1 0 RUDD 1 FLAPS NORM LAND FLAP 100 100 ELEV 0 0 AILE Timer Down Timer 5:00 Switch THR CUT Motor Stop Flap Switch Pos 0 = Normal Pos 1 = Motor Stop D/R 100 75 100 75 100 75 Expo* INH INH INH IN
DX8 SYSTEM SETUP Model Type SW Select Trainer F Mode All Others FUNCTION LIST ACRO Aux 1 Gear INH Servo Setup Chan Travel THR 100/100 AIL 100/100 ELE 100/100 RUD 100/100 D/R & Expo Chan Switch Pos (AIL D/R) 0 AILE 1 2 0 1 ELEV 2 Motor Stop Bind / I Button Pressed = Motor Stop Reverse Normal Normal Normal Normal D/R Expo* 100/100 0 100/100 0 75/75 0 100/100 0 100/100 0 75/75 0 Chan GER AX1 AX2 Travel 100/100 100/100 100/100 Reverse Normal Reverse Normal D/R & Expo Chan Switch Pos (AIL D/R) D/R Expo*
Installing the Flight Battery 1. Slide the battery into the back of the quadcopter, as shown, until it locks. 2. To remove the battery, press the locking tabs on both sides of the battery and pull the battery straight out the back of the quadcopter. CAUTION: Always remove the Li-Po battery from the quadcopter when not flying to avoid over-discharging the battery.
Technology ® SAFE® technology delivers: • Flight envelope protection you can enable at the flip of a switch. • Multiple modes let you adapt SAFE® technology to your skill level instantly. Best of all, sophisticated SAFE® technology doesn’t require any work to enjoy. Every aircraft with SAFE® installed is ready to use and optimized to offer the best possible flight experience. FlySAFERC.
Flight Mode Selection • In stability low angle mode (quadcopter LED blue), the controls provide a minimum bank angle. • In stability high angle mode (quadcopter LED green), the controls provide a maximum bank angle. • In agility mode (quadcopter LED red), the system does not self level. Use rates and expo to tune the performance according to your flying style. Refer to the Transmitter Setup Table for transmitter switch selection and specific setup information.
Using the Micro FPV Camera Consult local laws and ordinances before operating FPV equipment. In some areas, FPV operation may be limited or prohibited. You are responsible for operating this product in a legal and responsible manner. 1. Power on your radio transmitter, then power on the aircraft. 2. Power on the video receiver to make sure the channel is clear and then power on the video transmitter. 3.
Replacing the Propellers Follow the steps below to replace any damaged propellers: 1. Twist the top half of the protective cage of the affected propeller counter-clockwise to unlock, and lift it to remove the cage. 2. Remove 2 screws and remove the propeller by pulling straight up. 3. Note the propellers are marked “A” or “B” to show the proper location on the quadcopter. Using the illustration as a placement guide, replace the propeller.
Troubleshooting Guide Problem Quadcopter will not respond to throttle Possible Cause Throttle too high and/or throttle trim is too high Throttle channel is reversed AUX 1 reversed or not set properly prevents the motors from starting Motor start command not given correctly Quadcopter has reduced flight time or is underpowered Flight battery charge is low Inadequate power to flight battery charger Flight battery is damaged Flight conditions too cold Transmitter too near aircraft during binding process Dif
Exploded View 4 8 11 1 6 1 12 5 7 14 10 9 13 12 3 2 Parts Listings 1 2 3 4 5 6 7 8 9 10 Part # Description BLH9001 BLH9002 BLH9003 BLH9004 BLH9005 BLH9006 BLH9007 BLH9008 BLH9010 BLH9011 Propeller Set Main Frame Bottom Landing Gear Main Frame Top Dampers PCB Mount Camera Mount Prop Guards LED Cover FPV Camera 11 12 13 14 15 16 17 18 19 Part # Description BLH9012 BLH9013 BLH9014 BLH9015 BLH9016 BLH9017 BLH9017AU BLH9017EU BLH9017UK 3-in-1 Control Unit Power Switch Brushless Main Motor 800
Limited Warranty What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
Warranty and Service Contact Information Country of Purchase Horizon Hobby Horizon Service Center (Repairs and Repair Requests) United States of America Horizon Product Support (Product Technical Assistance) Sales United Kingdom Germany France Service/Parts/Sales: Horizon Hobby Limited Horizon Technischer Service Sales: Horizon Hobby GmbH Service/Parts/Sales: Horizon Hobby SAS Contact Information Address servicecenter.horizonhobby. com/RequestForm/ productsupport@horizonhobby.
©2016 Horizon Hobby, LLC. Blade, E-flite, Inductrix, SAFE, the SAFE logo, DSM, DSM2, DSMX, the BNF logo, AirWare, ModelMatch and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. All other trademarks, service marks or logos are property of their respective owners. Patents pending.
