Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni RTF READY-TO-FLY
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
Table of Contents Components ....................................................................3 Specifications ..................................................................3 Box Contents ...................................................................3 First Flight Preparation .....................................................4 Flying Checklist ...............................................................4 Charging Warnings...........................................................
First Flight Preparation Flying Checklist • Remove and inspect contents • Begin charging the flight battery • Install the flight battery in the quadcopter (once it has been fully charged) • Program your computer transmitter (BNF only) • Bind your transmitter (BNF only) • Familiarize yourself with the controls • Find a suitable area for flying ❏ Always turn the transmitter on first ❏ Plug the flight battery into the lead from the 5-in-1 control unit ❏ Allow the 5-in-1 control unit to initialize and arm properl
Installing the Transmitter Batteries (RTF) Replace the transmitter batteries when the power LED flashes and the transmitter beeps. Installing the Flight Battery 1 2 3 4 1. Lower the throttle to the lowest setting. For BNF aircraft, engage throttle hold if your transmitter ansmitter is so equipped equipped. 2. Power on the transmitter. 3. Install the battery by sliding it into the battery mounting slot below the control unit.
Transmitter and Receiver Binding If you are using a computer transmitter, set the model type to “Acro” or “Airplane” mode. In the channel input menu, set channel 6 (Aux1) to a momentary switch such as the bind button ( I ) and channel 5 (Gear) to a 3-position switch (switch B). In the Servo Setup menu, reverse channel 6 (Aux1). Bind the quadcopter to your transmitter following the Transmitter and Receiver Binding directions below. General Binding Procedure 1.
® Technology ® Revolutionary SAFE (Sensor Assisted Flight Envelope) technology uses an innovative combination of multi-axis sensors and software that allows model aircraft to know its position relative to the horizon. This spatial awareness is utilized to create a controlled flight envelope the aircraft can use to maintain a safe region of bank and pitch angles so you can fly more safely.
Flight Mode Selection RTF Change flight modes by pushing down on the right stick. Ensure the flight mode switch is in the desired position before flying. • In Stability Low Bank Angle mode (switch position 0), the controls provide a minimum bank angle. This mode is shown by the front and rear flight control LEDs on the quadcopter glowing solid green. • Agility mode (switch position 2) is shown by the front and rear flight control LEDs on the quadcopter glowing solid red.
Understanding the Primary Flight Controls If you are not familiar with the controls of your Ozone™ quadcopter, take a few minutes to familiarize yourself with them before attempting your first flight.
Flying the Ozone™ Takeoff Increase the throttle until the model is approximately 2 ft. (600mm) off the ground and check the trim so the model flies as desired. Once the trim is adjusted, begin flying the model. Typical flight times for the included battery range from 5 to 10 minutes. Low Voltage Cutoff (LVC) LVC decreases the power to the motors when the battery voltage gets low.
Problem Possible Cause Transmitter too near aircraft during binding process. LED on receiver flashes rapidly and aircraft will not respond to transmitter (during binding). Bind switch or button was not held while transmitter was powered on. Aircraft or transmitter is too close to large metal object, wireless source or another transmitter. Less than a 5-second wait between first powering on the transmitter and connecting the flight battery to the quadcopter.
Exploded View 9 12 7 8 13 8 13 18 9 12 4 5 1 14 17 LED 2 19 16 11 3 6 2 10 4 16 5 15 Parts Listings 1 2 3 4 5 6 7 8 9 10 11 EN Part # Description BLH9706 BLH9707 BLH9708 BLH9709 BLH9710 BLH9702 BLH9704 BLH9703 BLH9711 BLH9705 BLH7561 MQX main control board: Ozone MQX boom with Red LED MQX boom with White LED MQX CW motor MQX CCW motor MQX inner frame MQX canopy MQX propeller, CW rotation, green, (2) MQX propeller, CCW rotation, green, (2) MQX motor mount cover (semi-transp) Motor mo
Limited Warranty What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the "Product") will be free from defects in materials and workmanship at the date of purchase.
Warranty and Service Contact Information Country of Purchase United States of America Horizon Hobby Contact Information Horizon Service Center (Repairs and Repair Requests) Horizon Technischer Service servicecenter.horizonhobby.com/ RequestForm/ productsupport@horizonhobby.com 877-504-0233 websales@horizonhobby.com 800-338-4639 service@horizonhobby.
©2018 Horizon Hobby, LLC. Blade, Ozone, E-flite, Celectra, SAFE, DSM, DSM2, DSMX, the BNF logo, ModelMatch and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. All other trademarks, service marks or logos are property of their respective owners. Patents pending.
