Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni RTF
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.
EN Table of Contents First Flight Preparation ......................................................... 4 Flying Checklist ................................................................... 4 Installing the Propellers........................................................ 4 Installing the DXe Transmitter Batteries (RTF) ....................... 4 Charging Warnings............................................................... 5 Battery Charging (RTF) .......................................................
EN First Flight Preparation Flying Checklist • Remove and inspect contents • Begin charging the flight battery • Install the transmitter batteries (RTF only) • Program your computer transmitter (BNF only) • Install the flight battery in the aircraft (once it has been fully charged) • Bind your transmitter (BNF only) • Familiarize yourself with the controls • Find a suitable area for flying ❏ Always turn the transmitter on first ❏ Plug the flight battery into the lead from the ESC ❏ Allow the ESC to initializ
EN Charging Warnings • Always charge batteries away from flammable materials. • Always inspect the battery before charging. • Always disconnect the battery after charging, and let the charger cool between charges. • Always constantly monitor the temperature of the battery pack while charging. • ONLY USE A CHARGER SPECIFICALLY DESIGNED TO CHARGE LI-PO BATTERIES. Failure to charge the battery with a compatible charger may cause a fire resulting in personal injury and/or property damage.
EN Transmitter Setup The Spektrum DXe transmitter included with the RTF version of the quadcopter is programmed at the factory. If needed, the setup file can be downloaded at www.spektrumrc.com.
EN Transmitter and Receiver Binding The transmitter included with the RTF version of this aircraft is pre-bound to the receiver at the factory. If it becomes necessary to re-bind the transmitter to the receiver, follow the binding procedure below. To bind or re-bind your quadcopter to your chosen transmitter, follow the directions below. Binding Procedure 1. Select the correct model in your transmitter. 2. Power off your transmitter. 3. Lower the throttle fully. 4.
EN Understanding the Primary Flight Controls If you are not familiar with the controls of your quadcopter, take a few minutes to familiarize yourself with them before attempting your first flight.
EN Using the Video Transmitter Consult local laws and ordinances before operating FPV equipment. In some areas, FPV operation may be limited or prohibited. You are responsible for operating this product in a legal and responsible manner. See the Available Frequency table to find the desired video channel and Buttons LED window band. The video transmitter channel and band are changed using the buttons on the top of the quadcopter, as shown. There are two rows of LEDs visible through the LED window.
EN 4.3 inch Video Monitor with DVR Features 5.8GHz Antenna connector Menu Buttons: Use the + and – buttons to modify: Brightness Contrast Color Mode (16:9, 4:3) Language Reset Channel Selection Button Single push to change channel Frequency Band Button Single push to change band Micro Memory Card Slot ON/Off Switch Charge Status LED Red = charging Green = charged AV In 5V Micro USB Charge Port Record button Using the Video Monitor 3.
EN Preparing the Scimitar 170 Quadcopter for Flight 1. Before each flight, ALWAYS power on the transmitter before connecting the flight battery to the quadcopter. After each flight, disconnect the flight battery from the quadcopter before powering off the transmitter. NOTICE: Connecting the flight battery before powering on the transmitter can start the binding process. Please see the Transmitter and Receiver Binding section of this manual for more information. 2.
EN Troubleshooting Guide WARNING: Remove the propellers from the motors prior to performing any troubleshooting or maintenance. Failure to do so may cause serious injury if the motors start unexpetedly.
EN Parts Explosion 3 4 12 2 9 11 1 6 10 5 8 2 1 6 13 7 12 Parts Listings 1 2 3 4 5 6 7 8 9 Part # LH02301 BLH02303 BLH02304 BLH02306 BLH02308 BLH02309 BLH9403 BLHA1026 SPM4649T Description Center Frame: Scimitar 215, 170 Arm Set (4): Scimitar 170 Pod with LED: Scimitar 215, 170 4 inch FPV Props (4) 4in1 ESC BLHeli: Scimitar 170 Prop Guard Set: Scimitar 170 FPV Battery Strap: Theory X 1407 2820KV FPV Motor, Yellow DSMX Quad Race Receiver w/telemetry Part # 10 SPMFC3208 11 SPMVC602 12 SPMVT1000
EN Limited Warranty What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
EN Warranty and Service Contact Information Country of Purchase Horizon Hobby Horizon Service Center (Repairs and Repair Requests) United States of America Horizon Product Support (Product Technical Assistance) Sales European Union Horizon Technischer Service Sales: Horizon Hobby GmbH Contact Information servicecenter.horizonhobby.com/ RequestForm/ productsupport@horizonhobby.com 877-504-0233 websales@horizonhobby.com 800-338-4639 service@horizonhobby.
©2018 Horizon Hobby, LLC. Blade, the Blade logo, Scimitar, Thrust, DSM, DSM2, DSMX, Bind-N-Fly, BNF, the BNF logo, ModelMatch, Focal and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. All other trademarks, service marks or logos are property of their respective owners. US D774,933.
