ACM 5450 1 ACM 5450 PORTUGUÊS ESPAÑOL Operating instructions SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH DEUTSCH
PORTUGUÊS ESPAÑOL ACM 5450 ITALIANO 3 4 15 5 14 6 8 9 13 12 11 NEDERLANDS 2 10 SVENSKA 1 FRANÇAIS 7 3 ENGLISH
Table of contents Short instructions ........................ 15 Important notes ............................ 17 Precautions ........................................... 17 Traffic safety ......................................... 17 Installation/Connection .......................... 17 Anti-theft protection ..................... 18 Security code ........................................ 18 Entry of a wrong code number .............. 18 Switching on security coding .................
To alter a setting: Toggle the AUD button until the corresponding abbreviation and the adjusted value appear in the display. Extra function: To switch between stereo and mono: Hold down the button for approximately 2 seconds. With stereo playback, the stereo sign “ ” will appear in the display. ENGLISH FRANÇAIS 6 Cassette loading slot Insert tape (side A or 1 up; the open side facing to the right).
To recall a station: Select the memory bank with the FM button and press the corresponding preset button briefly. Extra function: Coding: Read chapter “Anti-theft protection” first. Buttons 1, 2, 3, 4 - To enter the fourdigit code. Press each of the buttons as many times as required until the code number given in the car radio passport appears in the display.
Station tuning – automatically, if “m” has disappeared from the display. – manual, if “m” lights up in the display. Toggle by pressing the lo button. Traffic safety As the driver of a motor vehicle, it is your responsibility to pay attention to the traffic situation at all times. Never use your car radio in a way that could distract you. Please keep in mind that you travel a distance of 14 m per second at a speed of only 50 km/h.
Anti-theft protection Security code Notice: This car radio is supplied with inactive code protection. In order to switch the security coding system on, proceed as described in the following. If the coding system is active while the power supply to the system is interrupted (e.g. theft, disconnection of the car battery), the set will be electronically blocked. In such a case it can only be made operable again by entering the correct code number given in the car radio passport.
switching the set on again. The display shows “CODE”. • Now enter the code number to be found in the car radio passport and confirm (see example under “Switching on security coding”). Security coding is now switched off. CODE LED To indicate that your unit is equipped with security coding, the LED flashes for extra security when the car is stationary.
If you leave the service area of the regional programme tuned into, or if you would like to take advantage of the full RDS service, switch to “REG OFF”. • Press the AF button for approximately 2 seconds until “REG OFF” appears. When active, “REG ON” will be briefly displayed each time the radio is switched on. Manual tuning Prerequisite: “m” lights up in the display. Toggle the lo button until “m” is displayed. ; the frequency will change in • Press short intervals in upwards or downwards direction.
You can recall any stored station at the touch of a button. • Select the memory bank by toggling the FM button until the desired level appears in the display. • Press the corresponding preset button briefly to recall the station. Traffic announcement priority on/off If the priority for traffic announcement programmes is activated, “TA” will light up in the display.
Tape operation Automatic seek tuning start Inserting a tape Prerequisite: The priority for traffic announcements has been activated. When leaving the reception area of the tuned in traffic programme station while listening to a tape or CD or after having turned down the volume completely, the system will automatically start searching for a new TA programme. If no such station is found within approximately 30 seconds, tape or CD operation will be stopped and a warning beep will sound.
Notice: If there is too much tension on the tape during playback, the set may switch over by itself before having reached the end of the tape side. In this case check the condition of the cassette tape. Sometimes it helps to rewind it completely. Make sure that a magazine is inserted. Press SRC to toggle between the available audio sources (radio - changer - tape). Press SRC as many times until the changer functions appear in the display. CD = disc, T = TRACK (title).
Appendix Mechanism/cassette tapes Specifications To avoid possible problems, you should not use cassette tapes longer than 60 or 90 minutes (C60/C90). Store your tapes in a cool place away from dirt, dust and temperatures exceeding 50 ° Celsius. Allow very cold tapes to warm up before playing them in order to avoid uneven tape transport. After approximately 100 hours of use, dust particles collected on the playback head or roller may lead to tape run problems and sound distortions.
Blaupunkt-Werke GmbH Bosch Gruppe 1/96 Pf 14 ACM 5450 K7/VKD 8 622 400 073 PM