Radio / Cassette Bergamo RCR 148 Montana RCR 148 Wiesbaden RCR 148 Operating instructions Ber/Mon/WiRCR148 d 1 08.05.
18 17 16 15 14 13 12 11 Montana RCR 148 Wiesbaden RCR 148 10 1 Bergamo RCR 148 4 2 5 6 11 2 3 4 7 8 9 Fernbedienung RC 06 (Option) Remote control RC 06 (optional) Télécommande RC 06 (en option) Telecomando RC 06 (optional) Afstandsbediening RC 06 (Optie) Fjärrkontroll RC 06 (Tillval) Mando a distancia RC 06 (opcional) Telecomando RC 06 (opção) 2 Ber/Mon/WiRCR148 d 2 08.05.
Contents Quick reference ............................ 25 Important notes ............................ 30 Precautions ........................................... 30 Traffic safety ......................................... 30 Installation ............................................. 30 Accessories .......................................... 30 KeyCard theft protection system 31 Operating the unit ................................. 31 Removing the KeyCard ........................
Switching on/off via the ignition: If the equipment has been connected correspondingly, the set can also be turned on and off with the vehicle ignition. After the ignition has been switched off, a double beep tone will remind you 3 For instantly muting the volume. button the volume By pressing the can be muted immediately. “MUTE” will appear in the display. The function is cancelled by pressing button or VOL+.
Tape operation 5 Display Remote control RC 06 (optional) a c / Title selection (S-CPS) Up Down Fast forward Fast rewind Stop function by pressing the opposite key. Extra rocker switch functions: Further setting functions with AUD B DSC Mode A PTY @ Condition: The corresponding function is activated. 26 k b Using the remote control you can execute the same functions as with the corresponding buttons of the car stereo. Exception: Radio operation << Press briefly. To switch the FM memory bank.
Travelstore To store and recall the six most powerful stations with Travelstore. To store: Press button for approximately 1 sec. until you hear a beep and “T-STORE” appears in the display. To recall: Select the memory bank “T” and press the corresponding preset button (1-6) briefly. 9 TA (priority for traffic announcements) When “TA” lights up in the display, the system will play traffic stations only. Priority on/off: Press TA.
Extra function of preset buttons To store and recall a PTY programme type. When PTY is active (“PTY” lights up in the display), you can store and recall one programme type on/from each preset button on FM. ; SRC (Source) You can switch between the radio and tape audio sources (if a tape is inserted). < lo To switch the seek tuning sensitivity level: Press button briefly. If “lo” is displayed, the radio will only pick up strong, local stations (normal sensitivity).
Setting the balance (left/right) and the fader (front/rear). Press AUD twice: Fader front Fader rear Balance left Balance right DEUTSCH ENGLISH FRANÇAIS Treble + Treble – Bass – Bass + Extra function AUD Loudness - When listening at a low level, the Loudness function creates a more natural sound by boosting the low frequency range. Loudness on/off: Press AUD for approximately 1 sec. “LD” lights up in the display if the Loudness function is switched on.
Important notes Precautions Installation Accessories Before starting to use your new car radio, please read the following information carefully. If you would like to install your new car stereo yourself or add other audio components to existing ones, then please read carefully the enclosed instructions on installation and connection. In order to ensure that the set operates properly it is necessary that the positive power supply line is connected to the ignition and the permanent +12 V lead.
This ensures that you will find your basic settings re-adjusted automatically as soon as you have inserted your KeyCard. After the display indications “CARD ERR” or “WRONG KC”: • Press ON to turn on the set. Removing the KeyCard • Pull out the KeyCard tongue and remove the card. “Training” a second KeyCard/ Replacing a KeyCard Operating the unit • Turn on the set.
Switching the audio source Short Additional Memory (S.A.M.) Optical indication of anti-theft protection Using the second KeyCard to be purchased at any specialised dealership, you can program a short text by selecting the DSC menu item READ KC. This text will be moved through the display and might be the telephone number of a car repair service or the emergency call number of your auto club.
The AF (Alternative Frequency) function makes sure that the strongest frequency of the currently selected programme is always tuned in automatically. This function is activated when “AF” appears in the display. In order to switch this function on or off, • press the AF button briefly. While searching for the strongest reception signal, the radio may switch to mute briefly.
Station tuning Automatic tuning / • Press / ; the car radio will automatically search for the next station. When keeping the upper or lower part / of the rocker switch depressed, seek tuning will speed up in upwards or downwards direction. Seek tuning Up Down << / >> Up/Down in short intervals (FM only, “AF” must be switched off) Manual tuning with << >> You can also tune in a station manually. Condition: AF and PTY must be switched off (i.e. the symbols do not light up in the display).
You can have all of the stored stations briefly scanned on all wavebands. Preset Scan cannot be started unless PTY has been switched off (“PTY” is not lit up in the display). • If necessary, press PTY. To start Preset Scan: • Press SC for approximately 1 seconds. All of the stored stations on the selected waveband will be scanned one after the other. In the display “SCAN” will alternate with the flashing station name or frequency. To select a scanned station and switch off Preset Scan: • Press SC briefly.
The sensitivity level can be altered separately in both modes. Please refer to chapter “DSC programming - S-LO, S-DX”). Switching from stereo to mono Every time the radio is switched on, stereo playback is activated automatically. The unit will gradually switch to mono if reception is poor. You can also switch between mono and stereo reception manually: • Press the lo button for approximately 1 sec. The selected condition will briefly appear in the display.
• Press << or >>. The programme type selected last will be displayed briefly. • Press << or >>; the programme type selected last will be displayed for 3 seconds. • During this period press >> (forwards) or << (backwards) to select the desired type. Selecting a programme type a) Using the preset buttons When PTY is switched on, you can use the preset buttons 1-6 to select the programme types stored at the factory. • Press one of the presets 1-6.
- PTY priority Situation: PTY is switched on and lights up in the display. No station offering the selected programme type can be currently received (neither with seek tuning nor with scan). The set will switch back to the previous station. As soon as a programme with such PTY can be received within the broadcasting network, the unit will switch over to the corresponding station for the duration of the programme. The system will switch to the linked NDR2 station for the duration of the “POP” programme.
• press a preset button which has a traffic programme station allocated to it. Alternatively: b) Switch off the priority for traffic announcements: ITALIANO • Press TA. “TA” will disappear from the display. Automatic seek tuning start (tape operation) Beep tone If you leave the reception area of the traffic programme station currently tuned into, you will hear a beep tone approximately every 30 seconds.
Tape operation Adjusting the volume for traffic announcements and the beep tone This volume was preset at the factory, though you can alter the value using the DSC function (see “DSC programming, TA VOL”). If the volume level is altered while a message is being played, this will only affect the current announcement. Fast Forward/Rewind The car stereo has to be switched on. The unit will automatically switch to tape operation when inserting a cassette. Inserting a tape • Turn on the set.
DEUTSCH When the tape is fast forwarded or rewound (also with CPS), the radio will normally be muted. In order to listen to the radio during fast winding, you can activate the Radio Monitor function. For more information please refer to chapter “DSC programming - RM ON/OFF”. PORTUGUÊS ESPAÑOL When a metal or CrO2 tape is inserted, the tape mechanism automatically adjusts to metal/CrO2 tape equalisation.
DSC programming DSC (Direct Software Control) allows you to customise certain programmable, basic settings to suit your personal needs and preferences and then store them. The basic settings for this audio equipment were made at the factory. In the following you can find an overview of these settings, so that you can always reset to these if desired. If you wish to alter any of the programming, • press SRC to select one of the operating modes radio or cassette (e.g.
To select the programme type language: DEUTSCH or ENGLISH VOL FIX Use this function to select the volume at which the radio is set when it is switched on. Adjust the desired volume level with << >>. When adjusted to “VOL 0”, the system will come on with the volume selected before switching it off. DEUTSCH ENGLISH OFF 3 35 4 ON ENGLISH 1 1 25 FRANÇAIS To adjust the seek tuning sensitivity for local reception.
Appendix Specifications Amplifier Output power: Tuner Wavebands: FM : 4 x 23 W RMS power acc. to DIN 45324 at 14.4 V 4 x 35 W max. power 87.5 – 108 MHz (only Bergamo RCR 148) MW 531 – 1602 kHz LW 153 – 279 kHz FM sensitivity: 0.
Blaupunkt-Werke GmbH Bosch Gruppe 10/97 Ts K7/VKD 8 622 401 345 24 Ber/Mon/WiRCR148 d 24 08.05.
