AUTORADIO BEDIENUNGSANLEITUNG:BREMEN SQR 46 DAB Bedienungsanleitung Operating instructions Mode d’ emploi Istruzionl of uso Gebruiksaanwijizing Bruksanvisining BR460 22.05.
Controls 1 2 3 4 5 6 7 8 9 Radio mode: Preset up/down. Long press: PTY search DAB: Change to preview/next known ensemble Long press: PTY search USB/SD: Change previous/next folder 10 11 Remote control window 12 < / > button 21 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 Display Bass Control Change the Bass level Treble Control Change the Treble level Button Button Radio mode: Manually step up/down.
Safety notes | Road safety Safety notes The car sound system was manufactured according to the state of the art and established safety guidelines. Even so, dangers may occur if you do not observe the safety notes in these instructions. These instructions contain important information to easily and safely install and operate the car sound system. • Read these instructions carefully and completely before using the car sound system.
Cleaning notes | Disposal notes | Scope of delivery | Placing the device in operation Declaration of conformity Optional equipment (not part of the scope of delivery) The Blaupunkt Competence Center Car Multimedia Evo Sales GmbH declares that the devices complies with the basic requirements and the other relevant regulations of the directive 2014/53/EU . The declaration of conformity can be found on the Internet under www.blaupunkt.com. Use only accessories approved by Blaupunkt.
Volume | DAB mode Switching on/off via vehicle ignition The car sound system will switch off/on simultaneously with the ignition if the device is correctly connected to the vehicle's ignition as shown in the installation instructions and you did not switch the device off by pressing the On/Off button. Volume Adjusting the volume You can adjust the volume in steps fron 0 (off) to 50 (maximum). Turn the VOL control to change the Volume.
Selecting an ensemble You can directly select ensembles that you have received once already (for this to work, the ensemble must be receivable). Briefly press the / button to change to the previous/next ensemble. The first available service in the ensemble is played. Note: With activated PTY function, the next service with the currently selected programme type is set (see the section "DAB-PTY" in this chapter). Ensemble seek tuning You can find new ensembles using seek tuning. Press the / button for approx.
DAB | Radio mode Switching between DAB and FM Switching the display Press the buttonDIS to toggle between these displays . You can select various settings for switching between DAB and FM radio mode. Switching may become necessary if the reception quality in the DAB or FM mode drops signigicantly. Switching between DAB and FM is selected in the user menu (see the chapter "User settings", section "Making settings in the "DAB TUNER" menu", menu item "SERVICELINK" ).
Radio mode Changing to radio mode or selecting a memory bank The following memory banks are available in the diff erent reception areas: Region EUROPE ASIA USA SOUTH AMERICA THAILAND Memory banks FM1, FM2, FMT, AM, LW FM1, FM2, FMT, AM, AMT Press the button SRC repeatedly until the desired memory bank is displayed. Note: • Up to 5 stations can be stored in each memory bank.
Radio mode | PTY Scanning stations With the scan function, you can scan either every receivable station or every stored station of the current waveband. Note: • You can adjust the scan time for each station (see the chapter "User settings", section "Making settings in the "VARIOUS" menu", menu item "SCAN TIME"). Scanning all receivable stations of the waveband Press the button MENU for approx. 2 seconds to start scanning.
Note: • If no station with the selected programme type is found ,”NO PTY” is briefly displayed and 2 beeps can be heard. The radio will then retune to the station that it played last. • If the tuned radio station or another station on the broadcasting network broadcasts your selected programme type at a later point in time, the car sound system will automatically switch from the currently tuned station or from the current audio source (e.g.
MP3/WMA/iPod mode Removing a USB data carrier S w i t c h e d o ff the car sound system so that the data carrier will be correctly unregistered. Disconnect the USB data carrier. After you pulled off the data carrier from the USB port at the front of the device, close the protective cap of the USB port : . Inserting/removing the memory card Open the USB cover. Insert the memory card with its labelled side up and its contacts first ito the cars slot untile tit clicks into place.
MP3/WMA/iPod mode Press the RPT button to change among the playback modes: Opera- Display tion iPod MP3/ WMA Gen. Meaning Repeating REPEAT TRACK tracks Repeating REPEAT TRACK tracks Repeating REPEAT FOLDER folders Regular REPEAT OFF playback If the REPEAT function is switched on, the icon (repeat tracks) or (repeat folders) is shown on the display.
MP3/WMA/iPod mode | Bluetooth® Note: You can also connect an external microphone for hand-free calling On MP3/WMA data carriers, you cand find a track based on its file name (see the chapter “Installation instruction”). and start the playback. Bluetooth technology is wireless is connection of short range. For this reason, Press the 1 button for approx. 2 seconds to start the search function.
Pairing and connecting a device Note: You can pair up to 5 Bluetooth® devices with this car sound system. Before you can pair a sixth device, you must first unpair one of the 5 already paired devices (see ch. "Additional functions in the Bluetooth® menu", section "Managing paired devices"). If you should attempt to pair a sixth Bluetooth® device, "PHONE LIST FULL – PLEASE DELETE ENTRIES FROM LIST" is displayed.
Bluetooth® Search the car sound system from your streaming device (Bluetooth® name) and establish the connection. Enter the PIN displayed by the car sound system, if necessary. The display may show "PAIRED", followed by "CONNECTED", as soon as the car sound system and the streaming device are paired and connected. Notes: • If no connection can be established, the display briefly shows "CONNECT FAILED". • If a Bluetooth® device is connected with the car sound system, the display shows the Bluetooth® icon .
Making a call In the Bluetooth® menu, select the "DIAL NEW NUMBER" menu item. Press the rotary control to open the entry menu. You can now enter a phone number with up to 20 digits: Turn the rotary control to select a digit for the respective position. Press the rotary control to go to the next position. Note: To return to the previous position in the entry menu, turn the rotary control until the "<" option is selected, and press the rotary control. Press the button to call the number entered .
Bluetooth® • If the spoken name is not being recognised or the time for the voice recognition has already expired, the display briefly shows "DIAL FAILED". • You can cancel the voice recognition by pressing the button. • Please note that the duration of the voice recognition is limited and depending on the respective cell phone. • You can also activate the voice recognition via speed dial (see the section "Speed dial for voice dial" in this chapter).
Bluetooth® 18 BR460 Bluetooth® streaming mode You can play back music from a Bluetooth® audio device via the loudspeakers of the car sound system if the audio device supports the Bluetooth® profile A2DP (Advanced Audio Distribution Profile). Starting the Bluetooth® streaming mode Press the SRC button repeatedly until "BT-STREAM" appears on the display. The playback starts. Notes: • The Bluetooth® streaming mode can be selected only if a suitable streaming device is connected.
Bluetooth® • The transfer does not delete the phone book from the cell phone. • You can access the phone book of the master telephone only if two cell phones are simultaneously connected with the car sound system. The car sound system can store the phone books of the paired telephones with a total of up to 1000 entries. If several numbers are stored on the telephone for one contact (e.g.
Bluetooth® As soon as the device is connected, “CONNECTED” is briefly displayed and you are returned to the device list. Note: If no connection can be established, the display briefly shows "CONNECT FAILED". If the device is already connected, the display Managing paired devices briefly shows "CONNECT EXIST". In the Bluetooth® menu, you can manage the paired Bluetooth® devices To disconnect the connection to the displayed device, (cell phones and streaming devices such as MP3 player).
Bluetooth® | External audio sources| To select the device shown as master telephone, press the rotary control to open the menu. Select the "SET AS MASTER" menu item. Note: The "SET AS MASTER" menu item is shown only if two cell phones are simultaneously connected with the car sound system. Press the rotary control and you are returned to the device list, and an asterisk symbol ( ) is shown next to the Bluetooth® name of the device.
Sound settings The following sound settings can be changed inthe "AUDIO" menu: • Adjusting bass and treble • Setting the left/right volume distribution (Balance) or front/rear (Fader) • Adjusting the increase of bass at low volume (Loudness) • Selecting a sound profile • Selecting level and frequency of the preamplifier output(Sub-Out). • Adjusting the time delay for switching in an external amplifier.
Sound settings Press the rotary control to change the setting for the selected menu item. Turn the rotary control to set the level or frequency. Press the rotary control to confirm the setting. AMP DELAY Setting the delay with which a connect amplifier is switched in. Settings: 0.5/ 1.0/1.5/2.0/2.5 seconds and OFF (no delay). Press the rotary control to change the setting. Turn the rotary control until the desired delay is set. Press the rotary control to confirm the setting.
Sound settings | User settings User settings Calling the user menu and selecting a menu Briefly press the MENU button to open the user menu. In the user menu, the user settings can be found in the following menus: – FREQUENCY (settings: 80/100/200 Hz) • TUNER – GAIN (settings: –7 to +7) • AUDIO (see chapter "Sound settings") – Q-FACTOR (settings: 1.0/1.25/1.5/2.0) • DISPLAY Press the rotary control to change the setting for the selected menu • VOLUME item.
User settings Press the rotary control to change the setting. Turn the rotary control to change between the settings. Press the rotary control to confirm the setting. If priority is switched on for traffic information, the display shows the icon . BAND SELECTION Activating or deactivating memory banks. Memory banks that can be deactivated: Region EUROPE ASIA USA SOUTH AMERICA THAILAND Memory banks FM2, FMT, AM, LW FM2, FMT, AM, AMT Press the button FM1>FM2>FM3>AMT directly access to the BAND SELECTION.
User settings | Making setting in the “VOLUME” menu Making settings in the "DISPLAY" menu DIMMER Select automatic or manual switching of the display brightness for day or night. Settings: AUTO (display brightness is automatically switched by switching the driving lights on or off), MANUAL (display brightness can be switched manually). Press the rotary control to change the setting. Turn the rotary control to change between the settings. Press the rotary control to confirm setting.
User settings HANDSFREE VOL Adjusting the minimum volume for telephone calls. Settings: 1 – 50. Press the rotary control to change the setting. Turn the rotaty control to set the volume. Press the rotary control to confirm the setting. Note: During the phone call, you can change the volume directly by means of the volume control. BEEP (button beep) Switching the confimation beep on or off Settings: ON, OFF. Note: When storing radio stations, a confirmation beep sounds even if the OFF setting is selected.
User settings | Factory settings SWC(Steering Wheel Conguration) Configuring the buttons of a connected steering wheel control. Press the rotary control to open the menu. Turn the rotary control to change between the functions. Press the rotary control to select a function. Press the corresponding button on the steering wheel control for approx. 1 second to program the button with the selected function. VERSION Displaying the current software version of the radio. Press the rotary control to open the menu.
Factory settings | Useful information | Technical data | installation Useful information Warranty The warranty terms can be called up from www.blaupunkt.com. Service If you ever need to use a repair service you will find information about service partners in your country under www.blaupunkt.com. Technical data Voltage supply Operating voltage: 10.5 – 14.4 V Current consumption In operation: <10A 10 sec. after swithch-ofF: < 3.5mA Amplifier Output power: 4 x 24 watts sine at 14.4 V at 4 ohms.
Installation instructions 1. 2. 0° - 30° ENGLISH +/– 10° ( This 2 cables are optional) 12/24 V +/– 10° 3. 1 2 3 Available as an optional accessory 1 2 3 4 5 6 7 6 5 7 4 4. Microphone In Steering wheel remote control Rear USB Preamp Out (Front) Preamp Out (Rear) Sub Out (Subwoofer) Radio antenna 182 165 53 Installation kits 1-20 30 BR460 30 setting. 22.05.
Installation instructions 5. 12/24 V A 1 2 3 4 5 6 7 8 * BR460 NC Telephone Mute NC Permanent +12V Auto antenna* Illumination Kl.15/Ignition Ground B 1 2 3 4 5 6 7 8 Speaker out RR+ Speaker out RR– Speaker out RF+ Speaker out RF– Speaker out LF+ Speaker out LF– Speaker out LR+ Speaker out LR– Switched power supply +12 V / max. 150 mA 22.05.
)&& :DUQLQJ 7KLV GHYLFH FRPSOLHV ZLWK 3DUW RI WKH )&& 5XOHV 2SHUDWLRQ LV VXEMHFW WR WKH IROORZLQJ WZR FRQGLWLRQV 7KLV GHYLFH PD\ QRW FDXVH KDUPIXO LQWHUIHUHQFH DQG WKLV GHYLFH PXVW DFFHSW DQ\ LQWHUIHUHQFH UHFHLYHG LQFOXGLQJ LQWHUIHUHQFH WKDW PD\ FDXVH XQGHVLUHG RSHUDWLRQ 127( 7KLV HTXLSPHQW KDV EHHQ WHVWHG DQG IRXQG WR FRPSO\ ZLWK WKH OLPLWV IRU D &ODVV % GLJLWDO GHYLFH SXUVXDQW WR SDUW RI WKH )&& 5XOHV 7KHVH OLPLWV DUH GHVLJQHG W
