C-RF6ir 6-Disc FM Modulator CD Changer with Infrared Sensor - For Use With Any FM Vehicle Radio Changeur de CD a capteur infrarouge /modulateur FM a 6 disques .
Owner’s Record The model and warranty numbers are located on the rear of the unit. Record the warranty in the space provided below. Refer to these numbers whenever you call upon your Blaupunkt dealer regarding this product. Model No. CDC-RF6ir Warranty Number FCC Warning The equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules.
Table of Contents Before installing and operating this unit, please read this manual thoroughly and retain it for future reference. Antes de instalar y operar esta unidad, por favor lea este manual detenidamente y guardelo para referencia en el futuro. English lndice Owners’s Record ................................................. 2 FCC Warning........................................................ 2 Features ............................................................... 4 Precautions ...............
Features Congratulations on your purchase of your Blaupunkt CDC-RF6ir FM Modulator CD Changer. This unit is designed to convert CD sound into FM signals (89.1 MHz or 88.7 MHz) and play them through any FM car stereo.
Before Installation and Testing (continued) Transport Lock SCWWS The mechanism in the CD changer is “locked” into place during shipment by three transport screws. Be sure to remove the screws prior to testing the system and installation. To keep dust out of the unit, which could cause a malfunction, place the enclosed seals over the screw holes after the Transport Lock Screws have been removed.
Electrical Connections Electrical Connections l Caution: before making connections, disconnect the ground wire terminal of the car battery to avoid shcrt circuits. l Use this unit only with negative ground 12 Volt (1 l- 16 Volt) direct current (DC). l Be sure to use the supplied changer cord. Using a cord other than the one supplied may cause noise or damage. l Be sure to connect the changer cord to the FM Modulator before mounting.
Installation . Recommendations l Carefully choose the mounting location so that the unit won’t interfere with normal driving. l Avoid installing the unit it a place: - Subject to temperatures exceeding 55 degrees C (131 degrees F) (such as in a car parked in direct sunlight.
Horizontal Installation Confirm that Anti-Vibration Switches on both left and right sides are set to position H. l Attach bracket (L) and bracket (Ft) using the hexagonal bolts (M5 x 8). l Attach brackets (L) and (R) to their respective brackets (B) using the hexagonal bolts (M6 x 20) and the hexagonal nuts (M6). l l 0 l l A CD 8 l l Pull back the carpet and determine where to attach the unit. Stick the supplied double-sided tape to the bottom of the brackets (B) and peel off the paper backing.
Vertical Installation onfinn that Anti-Vibration Switches on both left and right sides are set to position V, l Attach brackets (L) and (R) using the hexagonal bolts (M5 x 8). l Attach brackets (L) and (R) to their respective brackets (B) using the hexagonal bolts (M6 x 20) and the hexagonal nuts (MS). l l l Pull back the carpet and determine where to attach the unit. Stick the supplied double-sided tape to the bottom of the brackets (B) and peel off the paper backing.
45’ Installation I Confirm that Anti-Vibration Switches on both left and right sides are set to position 45. l Attach brackets (L) and (R) using the hexagonal bolts (M5 x 8). l Attach brackets (L) and (R) to their respective brackets (B) using the hexagonal bolts (M6 x 20) and the hexagonal nuts (M6). l I Pull back the carpet and determine where to attach the unit. l Stick the supplied double-sided tape to the bottom of the brackets (B) and peel off the paper backing.
. Sumended Installation Make sure that the unit does not hinder the movement of torsion bar spring or other parts of the trunk lid. l Confirm Anti-Vibration Switches on both the left and right sides are set to position “H”. l Attach bracket (L) and bracket (R) using the hexagonal bolts (M5 x 8). l 0 l Determine the mounting location and drill four mounting holes. 0 l Attach the CD changer with the tapping screws (M5 x 12). 3.
Installation of the FM Modulator install the FM Modulator to the floor or other surface with the included tapping screws (M3x12). Changer Specifications System Oversampling Laser Diode Frequency response Wow and Flutter THD (Total Harmonic Distortion) . Dynamic Range Signal-to-Noise Ratio Channel Separation Current Drain Compact disc digital audio system 1 -Bit/8 X Oversampling GaALAs Double Hetero Type 20-l 5,000 Hz +/- 3 dB Below Measurable limit Mass Power Requirement Part Number 0.
Magazine & Compact Discs Notes on the Disc Magazine Dirt, dust, scratches and warpage cause sound skips during playback and a deterioration of sound quality. Here are some suggestions on how to take care of your discs and the magazine: l Use compact discs that have the mark compact disc logo. DIGITAL AUDIO not use 3” (Scm) discs with the CDC-RF6k Handle the disc by its edge, and to keep the disc clean, do not touch the surface.
Magazine & Compact Discs Installing The Magazine 1. Slide the door toward the right. 2. Position the magazine so the top is facing up, and the arrow is facing the changer. Push it in until it clicks into place. Note: When the magazine is used for the first time, it will not lock into place unless the power supply has been connected. Make sure the door is closed. Otherwise, foreign matter may enter the unit, and contaminate the lenses inside the changer.
Operating Instructions l Before operating the unit for the first item (or after reconnecting the battery, etc.) press the Reset Button on the Commander. See page 5. Load the discs into the CD magazine and install the magazine into the CD charger. Turning Unit On/Playing A CD Vehicle ignition must be on. Turn on the car stereo and select FM band. Tune the radio to either 89.1 or 88.7 MHz. (depending on frequency chosen during installation).
Optional Wireless Remote Control The optional Wireless Remote CDC-RF6ir Control allows you to activate the following features in addition to the features that can be controlled with the CDC-RFGir’s Wired Commander: 5. MIX Button This plays the tracks or discs in a random /: 0OFF mON \ 0 7 sequence. 6. REPEAT Button This plays a certain track or disc over and 6 over again, 7. SCAN Button This plays the first portion of each track or disc. 8.
Troubleshooting Guide . The following check will assist in the correction of most problems that you might encounter with your unit. Perform the checks described below before contacting your Blaupunkt dealer. Symptom No Power Cause Fuse blown. Remedy Replace with a fuse of the same type and rating as the original. If the fuse blows again, consult with your dealer. Improper connection. Check connections. No Sound Improper connection. Check connections.
Error Codes If the changer malfunctions, one of the following error codes will be displayed: Error Display . . .I). ..... 0 I.... 111: : :: :...: 1.W. Cause : : 5 Disc change malfunction. Consult with dealer. Disc loaded with print facing up or disc is dirty. Load disc properly. Clean disc. Temperature inside car too hot. Allow the car to cool. Then press the Play/Pause Button. 1.1 HI .” ..I Magazine has not been installed. Install magazine. :...: :.I.: :...p : :-: !! : k-1 5...: :...
a BLAUPUNKT Bosch Group Robert Bosch Corporation Sales Group-Blaupunkt Division 2800 South 25th Avenue, Broadview, Illinois 60153 Robert Bosch Inc. 6811 Century Avenue Mississauga, Ontario Canada L5N 1 Rl Robert Bosch S.A. de C.V. Dr. Lucia 270, Cols. Doctores, Mexico D. F. 06720 Copyright 1994 by the Robert Bosch Corporation No portion of this work may br reproduced in any form without the written consent of the Robert Bosch Corporation.