Mobile Navigation TravelPilot Lucca TravelPilot Lucca MP3 Operating and Mounting Instructions Lucca_long_2G_eng.indd 1 13.04.
Device Overview Device Overview 1 2 3 4 5 6 2 Lucca_long_2G_eng.indd 2 13.04.
Device Overview The following button are located below the display: 1 INFO: Repeats the last travel instruction. 2 MENU: Opens the start screen of the device. 3 On/Off switch: Short press: Starts the device in the previously used mode or switches the device to a state of rest. Long press (longer than three seconds): Switches the device off. 4 VOL-: Decreases the volume. 5 VOL+: Increases the volume.
Device Overview The underside features the following controls: = < ; : > : Battery compartment cover ; Battery main switch < GPS antenna socket for connecting an external GPS antenna. = Support ? > Socket for connecting the Lucca to the cradle. The cradle provides additional functions. For further information, please read the "Cradle" chapter. ? Reset button. Restarts the Lucca. 4 Lucca_long_2G_eng.indd 4 13.04.
Contents Device Overview ......................2 Switching on/off ....................16 Safety notes ...........................10 Switch-on ................................... 16 Activating the Idle State............. 16 Switch-off .................................. 16 Reactivating ............................... 16 Safety Notes for Navigation ....... 10 Safety Notes for Handling the Lucca ........................................ 10 Initial Startup of Lucca ..........11 Lucca Scope of Delivery .....
Contents Navigating Home ........................ 23 Showing a Map .......................... 23 Traffic Jam Reports.................... 23 Settings...................................... 23 Exiting the Menu (Lucca MP3 only) ....................... 24 Additional Functions .................. 24 GPS Info..................................... 24 Route Planning........................... 24 Performing Basic Settings ............ 24 Setting the Time Zone ............... 24 Entering the Home Address .......
Contents Editing, Saving and Managing Routes........................................ 46 Changing the Order ................... 47 Deleting a Route Point ............... 47 Deleting a Complete Route List .. 47 Managing Routes .......................... 48 Saving a route ............................ 48 Loading a route .......................... 48 Calculating a Route ....................... 48 Displaying the Route on the Map .. 49 Simulation (demo mode) ........... 49 Specifying Route Options ......
Contents Additional Functions during Navigation ..............................64 Inserting an Interim Destination ... 64 Approaching the Next Destination . 65 Blocking route segments .......65 Manual Blocking......................... 65 Unblocking ................................. 66 Using the TMC Functionality ......... 67 Traffic Reports with TMC ........... 67 TMC Mode of Operation ............ 67 Showing TMC Messages ............ 68 Refreshing TMC Messages ......... 68 Closing the TMC Messages Menu ..
Contents Selecting a Directory via File Browser ..................................... 79 Configuring the Display ................ 85 Selecting Tracks/Files ................... 79 Adjusting the Picture to the Display Format .............................. 86 Selecting a Track via Button ...... 80 Removing the SD Card.................. 86 Configuring the Display ................ 80 Installing Street Maps ...........87 Random Track Play (Mix/Shuffle) . 80 Removing the SD Card ...............
Safety notes Safety notes For your personal benefit, please carefully read the following safety notes and warnings before operating your Lucca for the first time. Safety Notes for Navigation Caution: Do not operate the Lucca while driving to protect yourself and others against accidents! View the display only if you are in a safe travel situation! The street routing and traffic signs have priority over the instructions of the navigation system.
Initial Startup • • constantly uses electricity and could discharge the vehicle battery. Do not unplug the connector by pulling on the wire. The wire could be damaged! Do not use harsh solvents to clean the device; use only a damp, lintfree cloth. Initial Startup of Lucca If you are starting up the Lucca for the first time, you must switch on the main switch and set your preferred language for the menus and the voice output.
Initial Startup Protective Films and Covers Prior to the initial use, remove the protective films from the display and front of the housing. Before using the cradle, please remove the elastic cover at the bottom of the housing. Before inserting an SD card, please remove the dummy card. To protect the contacts, you can apply the elastic cover and dummy card again after using the Lucca. Switching the Main Switch On/Off The main switch allows for switching the Lucca on and off.
Charging the Battery Setting the Language Charging the Battery If the Lucca was switched off using the main switch, US English is used as the standard language. If necessary, you may have to set the desired language for the menus and the voice output: ➜ Switch on the Lucca using the On/ Off switch . ➜ Touch Settings. Touch or until Language appears. A list with available languages is displayed. ➜ Touch the language in the list that you want to use for menus and voice output.
Installation in the Vehicle The number of dark block segments on the battery indicates the charge state of the battery (0 to 3 segments). Note: If the charge state of the battery is very low, a warning message is displayed. ➜ To charge the battery, attach the supplied charger or the cigarette lighter wire to the charging socket. Note: Use only original chargers for operating and charging the battery. The charging 6 hours. time is approx.
Installation in the Vehicle ➜ Locate a suitable place for installing the Lucca. To ensure a perfect hold, the glass must be free of dust and oil. If necessary, clean the glass first using the supplied lens cleaning tissue. ➜ Press the suction plate of the support against the glass. ➜ Push the lever on the suction support towards the glass. ➜ The holder can now be adjusted. The track for mounting the Lucca must be aligned vertically.
Switching on/off ➜ Carefully push the guide of the Lucca over the track of the suction cup holder. Installing Lucca in the Cradle The cradle features a track for mounting the Lucca on the inside. ➜ Carefully push the guide of the Lucca over the track of the suction cup holder. Removing the Lucca ➜ Pull the Lucca up and out of the cradle or the support. If necessary, securely support the cradle or the support. Switching on/off Switch-on ➜ To switch on the Lucca, push the below the display.
Operating the Navigation Menus Operating the Navigation Menus Software Keyboard If text entries are required, the touchscreen displays a software keyboard. You can perform all entries using your finger. Only capital letters can be entered. You do not have to enter any special characters or umlauts when entering city or street names. The Lucca completes these characters automatically.
Operating the Navigation Menus This is the case, for example, if you do not enter the complete name of a place during the entry. After every entry of a letter, the text field shows the first entry that starts with the previously entered characters. To display a list with additional matching entries, touch the List button. The end of the list features entries what contain the sequence of previously entered characters not at the beginning, but in the middle or at the end.
Operating the Navigation Menus punkt start screen (Lucca MP3 only). Here, you can open another application, such as the MP3 player or the Picture Viewer, or reopen the navigation. • More: Touch this button to obtain access to additional functions. Depending on the menu in which this button is located, different functions are offered. If this button is deactivated, no additional functions are available. use the Lucca to show the TMC messages on the display.
Operating the Navigation Menus ➜ Touch the arrow buttons in the Message area to change between the individual TMC messages. For each TMC message, the street number (motorways, regional and local street) as well as the type of jam is displayed. ➜ Touch the Update display button to display TMC messages that arrived since you opened the TMC messages menu. ➜ Touch the button to close the TMC messages menu.
Operating the Navigation Menus • • • • • Longitude/Latitude, current Position: Information of the east longitude and north latitude. Satellites: Number of satellites received. The navigation requires signals from at least three satellites. HDOP: Horizontal Dilution of Precision. Indicates the quality of the positioning. Theoretically, values from 0 to 50 are possible, whereby the following applies: The lower the value, the more precise the positioning (value 0 = no deviation from the actual position).
Navigation Navigation General Notes about the Navigation The use of the Lucca is at your own risk. Starting the Navigation ➜ Switch on the device using the button. ➜ In the start screen (Lucca MP3 only), touch the Navigation button. Caution: Do not operate the Lucca while driving to protect yourself and others against accidents! View the display only if you are in a safe travel situation! The street routing and traffic signs have priority over the instructions of the navigation system.
Navigation The Navigation menu allows access to all the functions of the navigation. For further details, please read the section "Working with the Map". Note: The Lucca always starts with the screen that was active when you switched off the device. Traffic Jam Reports ➜ Touch the Traffic jam reports button to obtain an overview of the currently valid traffic reports that were received by your radio system.
Navigation Exiting the Menu (Lucca MP3 only) ➜ In the Navigation menu, touch to quit the navigation. The Lucca start screen displays. Additional Functions ➜ Touch the More button to gain access to additional functions of the Navigation. The list of additional functions displays. GPS status and about your current position. Route Planning ➜ Touch the Itinerary button to plan a route with several stages. For further details, please read the section "Route Planning with Stages".
Navigation ➜ Touch the button until the screen displays the Time zone button. ➜ Next, touch Time zone. The Time zone menu displays. ➜ Touch the OK button. ➜ If daylight savings time currently applies to your position, touch the Daylight saving time button. The button displays a check mark. Note: If the time is changed at your position or if you drive into a different time zone, you must adjust the corresponding settings. ➜ Touch the OK button. The Navigation menu displays. ➜ Touch Time zone.
Navigation Specifying a Destination This section contains information about the different methods for entering, selecting and managing destinations with the Lucca. How to start the navigation to a destination is described in the chapter "Destination Guidance". ➜ Touch the Enter your home address button. The Destination entry menu displays. ➜ Touch the Address button and enter your home address. See "Entering a Destination Address". ➜ Touch the Set as home address button.
Navigation Entering a Destination Country First, enter the country in which your destination is located. Note: This entry does not have to be repeated. If your destination is in a different country than the previous one, you must re-enter the country. ➜ In the main menu (Lucca MP3 only) touch the Navigation button. The Navigation menu displays. ➜ Touch the Destination entry button. The Destination entry menu displays. ➜ Touch the Country button. The list of countries displays.
Navigation Note: You can only select countries which are at least partially displayed on the currently loaded map. Entering a Destination Address ➜ In the main menu (Lucca MP3 only) touch the Navigation button. The Navigation menu displays. ➜ In the Navigation menu, touch the Destination entry button. The Destination entry menu displays. ➜ Touch the Address button. The Address menu displays.
Navigation Intersection field to enter the crossroad to the defined street. Note: How to save a defined destination is described in the chapter "Saving one of the recent destinations". Additional Functions ➜ Touch the More button to gain access to additional functions of the Address menu. The list of Additional functions displays. The list of Additional functions contains the following functions: • Route options: – Here you can set the route options for the next navigation.
Navigation ➜ In the main menu (Lucca MP3 only) touch the Navigation button. The Navigation menu displays. ➜ In the Navigation menu, touch the Destination entry button. The Destination entry menu displays. ➜ Touch the Points of interest button. The Point of interest menu displays. ➜ Touch the ... nearby button. The submenu displays. ➜ Touch the Surrounding Radius field and select the radius in which you are looking for a point of interest. ➜ Touch the Category field and select the category (e.g.
Navigation Shell, etc. from which you want to look for points of interest. Only those subcategories are available for selection for which points of interest can be located in the current vicinity. ➜ Touch the Point of interest field to select a specific target. The keyboard is displayed. If you know a part of the description of the point of interest, it can be entered here to shorten the list. ➜ Touch the List button. A list with points of interest appears.
Navigation • Show on map: – Select this button to view the specified address on the map. For further details, please read the chapter "Working with the Map". • Save: – This function allows you to save the specified address to your favourites. For further details, please read the chapter "Saving one of the recent destinations". Point of Interest at a Specific Location ➜ In the main menu (Lucca MP3 only) touch the Navigation button. The Navigation menu displays. ➜ Touch the Destination entry button.
Navigation ➜ Note: If the country containing your destination is not displayed in the first line, touch the button twice and select the correct country. How to select a country is described in the chapter "Entering a Destination Country". ➜ Touch the Location field and enter the location in which you are looking for a point of interest. You can enter either the postcode or the name of the location. Touch the Category field and select the category (e.g.
Navigation ➜ Touch the List button. A list with points of interest appears. The points of interest displayed correspond to the selected category and subcategory. They also contain the characters you entered (if you entered any characters). ➜ Touch the entry of the point of interest to which you want to navigate. ➜ If you desire more detailed information about the point of interest, touch the More button, followed by Show details. ➜ Touch the OK button to accept the selected point of interest.
Navigation The submenu displays. ➜ ➜ Note: If the country containing your destination is not displayed in the first line, touch the button twice and select the correct country. How to select a country is described in the chapter "Entering a Destination Country". ➜ Touch the Category field and select the category (e.g. airport) from which you want to look for points of interest. The selection offers only categories whose points of interest have a national meaning.
Navigation Copying a Destination from the Map This function allows you to select the destination for a navigation directly on the map. In addition to towns and streets, you can also quickly select points of interest. ➜ In the main menu (Lucca MP3 only) touch the Navigation button. The Navigation menu displays. ➜ Touch the Destination entry button. The Destination entry menu displays. ➜ In the destination entry, touch the Select on map button. The map is displayed.
Navigation – Move In the move mode (button pressed), you can move the map. For this purpose, touch the map, hold the pen or your finger pressed and move the map area in the desired direction. ➜ Touch the town (street or point of interest) to be defined as the destination for a few seconds. The town is identified by an orange-dotted circle. Information about the selected location is loaded from the data stock and displayed.
Navigation Notes: – This function is only available with GPS reception. – If you use this function during a navigation, all previously defined route locations (stages and destination points) are deleted! • Touch the Save button to save the selected destination. You can select the destination at any time from the list of favourites. • Touch the Search nearby button to search for a point of interest in the vicinity of the selected destination.
Navigation Copying the Destination from the Favourites The favourites contain all the destinations you saved using the Save button. You can perform the following in this menu: • Accepting destinations for the navigation, • renaming navigation destinations, and • deleting saved destinations. Copying a Favourite for Destination Guidance ➜ In the main menu (Lucca MP3 only) touch the Navigation button. The Navigation menu displays. ➜ Touch the Destination entry button. The Destination entry menu displays.
Navigation Additional Functions ➜ Touch the More button to gain access to additional functions of the Favourites menu. The list of Additional functions displays. It contains the following functions: • Show details: – Touch the Show details button to show the address of the selected destination. • Delete entry: – Touch the Delete entry button to delete the selected destination. • Delete all: – Touch the Delete all button to delete all the destinations from the Favourites.
Navigation • • • ➜ Select the desired destination. ➜ Touch the OK button. The destination is copied and the address is entered in the corresponding fields. Additional Functions ➜ Touch the More button to gain access to additional functions of the Recent destinations menu. The list of Additional functions displays. It contains the following functions: • Show details: – Touch the Show details button to show the address of the selected destination.
Managing Destinations The route calculation is performed and the navigation starts. Note: The route type used for the route calculation is automatically selected from the setting which you defined in the Routing options menu. Managing Destinations Two lists are available in which individual destinations are saved: • In the Favourites • In the Recent destinations list Each destination you specify and the destinations from the Recent destinations list can be saved in the Favourites.
Managing Destinations A menu for entering a name is displayed. ➜ Enter a name for the destination. ➜ Touch the OK button. The destination is saved in the Favourites. Saving one of the Recent Destinations Prerequisite: • You opened the Recent destinations list as described in the chapter "Copying one of the Recent Destinations". ➜ Select the destination which you want to save in the Favourites. ➜ Touch the More button. ➜ Touch Save under favourites. A menu for entering a name is displayed.
Managing Destinations ➜ Select the destination to be renamed. ➜ Touch the More button. ➜ Touch Rename entry. A menu for entering a name is displayed. ➜ Enter a new name for the destination. ➜ Touch the OK button. The destination is renamed. Deleting a Destination Prerequisite: • You opened the Favourites as described in the chapter "Copying the Destination from the Favourites" - or • you opened the Recent destinations list as described in the chapter "Copying one of the Recent Destinations".
Route Planning Route Planning with Stages ➜ Touch OK to delete the list - or not to delete the list. ➜ touch You can also perform the route planning without GPS receiver, e.g. in the comfort of your home. Defined routes can be saved for reuse so that you can plan any number of routes, e.g. for your vacation. Entering Destination Points A route is planned as follows: ➜ In the Navigation menu, touch the More button. ➜ Touch Itinerary. The Itinerary menu displays.
Route Planning The Destination entry menu displays. ➜ Define the route point similar to the destination entry. For more information, see the chapter "Entering a Destination". ➜ Touch the Add button. The Itinerary menu displays. The defined destination is listed as route point 1. ➜ Repeat the steps for all additional destinations to be added to the route. Adding a Route Point ➜ Touch the Add button to define another route point. The Destination Entry menu displays.
Route Planning If the list features more than 3 entries, use the following buttons: button to scroll up ➜ Touch the the list by one page (3 elements). button to scroll down ➜ Touch the the list by one page (3 elements). To scroll up or down the list by several pages, ➜ touch the corresponding button repeatedly. Note: If the list features more than 3 elements, the scroll bar indicates the current position in the list. Changing the Order • Move route point up: ➜ Select the route point to be moved.
Route Planning Managing Routes Saving a route ➜ Touch the More button. ➜ Touch Save route. A menu for entering a name is displayed. ➜ Enter a name for the route. ➜ Touch OK. Note: The route points are saved. If you load a saved route, it must be recalculated. Loading a route ➜ Touch the More button. ➜ Touch Load route. ➜ Select the desired route. ➜ Touch OK. Calculating a Route Note: For a navigation, the current position is the starting point.
Specifying Route Options Displaying the Route on the Map ➜ Touch the Show on map button to display the entire route on the map. The map is displayed. The route is highlighted in blue. The specified route points are identified by flags. Simulation (demo mode) ➜ Touch the map. A selection menu appears. Touch "Simulation". The route is automatically travelled and driving recommendations are output. to end the simula➜ Touch tion, otherwise the simulation is repeated.
Specifying Route Options The Routing options menu displays. ➜ Touch the Speed profile field to change between the available profiles. ➜ Touch the Type of routing field to change between the various modes: • Dynamic route (TMC) – This option requires that an external TMC receiver is connected. With this option, traffic announcements are incorporated in the calculation of the route. Without TMC reception, the Fast Route is calculated.
Destination Guidance Destination Guidance Prerequisite: • You specified a place of destination as described in the chapter "Entering a Destination" - or • you selected a place of destination from the Favourites as described in the chapter "Copying the Destination from the Favourites" - or • you selected a place of destination from the Recent destinations list as described in the chapter "Copying one of the Recent Destinations" - or • you planned or loaded a route (as described in the chapter "Route Plannin
Destination Guidance Disturbed GPS Reception A message appears after entering the destination if no adequate GPS signal is received. You have the following options: • Open the battery cover and ensure that the switch inside is set to "ON". • If you are in an enclosed room, move to the outside. The Lucca requires a vertical line towards the sky. If the GPS reception is disturbed during the destination guidance, the navigation is stopped.
Working with the Map Working with the Map Map Operation In this section you learn which information and which processing options are available in the map view. Depending on whether you display a map without or during the navigation, different options are available for operation. Showing a Map You can display the map • during route planning, • to display destinations on the map, or • to copy destination from the map for the navigation.
Working with the Map Buttons • Different buttons are available in the map view with which you can adjust the display according to your needs. • With Map View without GPS Reception • Show/hide buttons – More This button allows you to hide the other buttons to gain a better overview of the map. Touching it again redisplays the auxiliary buttons. With Map View with GPS Reception • Auto mode – More Touch this button to restore the standard view of the map after making changes.
Working with the Map • – Position fixed (standard setting) In this mode (button pressed), the map is continually moved so that the current position (yellow arrow) is always closely centred in the bottom third of the map. Zooming / Moving – Touch the Zoom /Pan , button to switch between zoom and pan mode. – Zoom In the zoom mode (button not pressed), you can zoom in and out on the map. You can zoom in by plotting a diagonal starting in the top left corner.
Working with the Map • • • • • 2D-view – Touch the More, button to display the map in two-dimensional form again. Zoom out – Touch this button to zoom out of the map. Zooming level bar between the buttons / – Touch one of the sections of the bar to zoom in or zoom out of the map. Zoom in – Touch this button to zoom in on the map. TMC status – TMC reception / Touch this button to display current traffic announcements.
Working with the Map Additional Functions ➜ Briefly touch any position on the map to activate additional functions. Depending on whether you are currently in a navigation or only display the map, only certain functions are available. The menu with the additional functions displays. Day/Night Mode ➜ Touch the Night mode, button to set the map display "Night" or "Day". Mute ➜ Touch the Mute button to switch the voice instructions on or off. Settings ➜ Touch the Settings button to display the Settings menu.
Working with the Map Afterwards, all subsequent route points are selected. For further details, please read the section "Inserting an Interim Destination". Route Options ➜ Touch the Route options button to change the route options. For further details, please read the section "Routing options". Next Destination This function is only available during a navigation on a route with at least one interim point. Use this function if you want to skip the next route point.
Map Display during a Destination Guidance Map Display during Destination Guidance During a navigation, the map display shows different navigation tools, route information and one additional button: Navigation Tools The left and lower area of the map display the following navigation tools: • • • In case of actions that must be executed in brief succession, the next to one action is displayed in the small upper arrow field. The yellow triangle represents your position on the map.
Map Display during a Destination Guidance • • – The more yellow bars are displayed, the closer you are to the location of the next action. The upper street field displays the next street name. The lower street field displays the current street name. Route Information The right area of the map displays the following route information: – : This symbol represents stages. All information below it refers to the next destination. – : Estimated time of arrival. : Estimated remaining – travel time.
Working with the Map Caution The information on the digital road maps may be incorrect due to shortterm changes (construction, etc.)! The traffic situation and the local signpost information have priority over the information of the Lucca. Showing Additional Map Information You can use the Lucca to define which additional information is displayed on the map. All settings are performed in the Settings menu.
Map Display during a Destination Guidance ➜ Activate the Street names 2D entry so that the street names are displayed on the map (only possible in 2-D display). button to return ➜ Touch the to the Settings menu. The corresponding information for the next stage (upper area) and the complete route (lower area) is displayed on the map. Route Information ➜ Select the Route information setting with the button. ➜ Touch the button to return to the Settings menu.
Map Display during a Destination Guidance The Speed limit menu displays. In the Speed limit menu you can define whether speed limits should be displayed during the navigation and whether you should be warned audibly if you are exceeding the speed limit. • Display signs ➜ Touch the Show traffic signs button to change between the modes Show traffic signs : Always, On speeding only or Never.
Additional Functions during Navigation ➜ Touch the Warning outside builtup areas button to change the value or to set it to Never. • Warning – Activate the Warning button to receive an audible warning. ➜ Touch the OK button to save your settings. Your settings are accepted and displayed on the map.
Additional Functions during Navigation ➜ Touch the Interim destination button. The Destination entry menu displays. ➜ Enter the place of destination as described in "Entering a Destination". ➜ Touch the Set as route point button. The route is recalculated and the defined interim destination is selected as the next route point. Note: You can also select the interim destination directly from the map as described in the section "Copying a Destination from the Map". Next, touch Interim destination.
Additional Functions during Navigation Supposing that you are on the motorways and hear a traffic announcement on the radio about a traffic jam of 5 km on your route. In this case, you can use a manual blocking of the section to evade the traffic jam. The manual blocking is only applicable to the current navigation and is no longer available for a new navigation or after a restart of the program. Route segments are blocked as follows: Prerequisite: • You are in the map display during a navigation.
Additional Functions during Navigation Using the TMC Functionality Traffic Reports with TMC The Traffic Message Channel (TMC) supplies your Lucca with traffic reports. This is made possible by a Blaupunkt car sound system with TMC receiver that receives the traffic reports broadcast by the radio stations.
Additional Functions during Navigation Note: This function can only be used if you connected an external TMC receiver, e.g. a corresponding Blaupunkt car sound system. Please ensure that the Lucca is always switched on first, followed by the TMC radio. The TMC reception is indicated by the green TMC symbol in the map display with connected TMC radio and TMC station. ➜ Touch the More button. symbol. ➜ Touch the The TMC messages menu displays.
Additional Functions during Navigation Automatic Route Change Prerequisite: • You configured the Lucca so that route changes are performed automatically (default setting). The report of traffic obstruction on your route results in the automatic calculation of an escape route. Manual Route Change Prerequisite: • You configured the Lucca so that you must manually confirm route changes. If a traffic obstruction on your route is reported, an information window appears.
Configuring Lucca Configuring Lucca / Basic Settings Settings You can perform settings in the Lucca for the following areas: • Touchscreen calibration • Factory settings • Map information • Route information • Signpost information • Speed • Volume • Touchscreen calibration • Auto mode • Routing options • Route planning • Time zone • Format • TMC • Home address • Voice output • Product information • Language ➜ In the Navigation menu, touch the Settings menu to configure the Lucca.
Configuring Lucca Map Information In the Map information menu, you can perform the following settings: • Info bar – If you activate the entry, the compass, altitude and current speed are displayed on the map in the lower right border. • Points of interest – If you activate the entry, the map displays all the points of interest (Points of interest). • Street names 2D – If you activate the entry, the map displays all the street names.
Configuring Lucca Signpost Information In the Signpost information menu, you can specify whether signpost information, which you are to follow, should be displayed during the navigation or not. ➜ Touch the Show traffic signs, button to activate or deactivate the display. Note: This information can only be displayed if it is part of the map material.
Configuring Lucca ➜ Touch the Warning outside builtup areas button to change the value or to set it to Never. • Warning ➜ Activate the Warning button to receive an audible warning. Volume In the Volume menu, you can set the volume. ➜ For this purpose, touch the Volume field and select a different value. Note: This information can only be displayed if it is part of the map material.
Configuring Lucca • • 3D auto zoom – Select whether you desire auto zoom or no auto zoom as default in 3-D view during a navigation. 2D auto zoom – Select whether you desire low auto zoom, standard auto zoom, high auto zoom or no auto zoom during a navigation with 2-D view. Note: For 2-D and 3-D auto zoom, the zoom depth is changed in reference to your speed: If you travel slowly, the scale becomes smaller. If you travel faster, the scale becomes larger.
Configuring Lucca Time Calculation In the Time zone menu, you can set the time zone that is valid for your position. This setting is important for the correct calculation of estimated arrival times. • Time zone ➜ Touch this field to set the time zone valid for your position. • Daylight saving time ➜ Touch this field to toggle between daylight savings time (button with check mark) and winter time (button without check mark).
Configuring Lucca Home Address In the Home address menu, you can store your home address so that you can quickly navigate home from any location. ➜ Touch the Enter your home address button. ➜ Touch the Address button and enter your home address in the "Entering a destination address" section. ➜ Touch the Set as home address button. The address is copied into the Home address menu. Product Information ➜ Touch this field to display the version of the map being used and the version of the navigation software.
GPS If the Lucca receives the signals from at least 3 satellites, it can determine its position and display it on the map. This position can then be used as the starting point for a route calculation. Since a positioning and position display is carried out once every second, you can view your movement on the map. MP3/WMA Mode MP3/WMA Mode (Lucca MP3 only) The Lucca can be used to play MP3 audio files in MP3 format and WMA from SD cards.
MP3/WMA mode Inserting the SD Card The Music menu displays: The SD card slot is located on the right side of the Lucca MP3. ➜ Push the SD card into the SD card slot according to the marking on the slot until the card engages. Selecting MP3/WMA Mode If you are in a different operating mode, ➜ press the MENU button below the display to display the main menu. The main menu displays.
MP3/WMA mode Selecting a Directory via Button ➜ To select the next higher direcbutton in the tory, touch the Music menu. ➜ To select the next lower directory, button in the Music touch the menu. Selecting a Directory via File Browser ➜ In the Music menu, touch the More button. The menu with the additional functions is displayed. The file browser is displayed. ➜ Touch the desired directory. The directory is displayed. ➜ Touch the track to which you want to listen.
MP3/WMA mode Selecting a Track via Button ➜ To select the next track in the dibutton in the rectory, touch the Music menu. ➜ To select the previous track in the button in directory, touch the the Music menu. The next or previous track starts playing. Configuring the Display You ca define whether the tracks in the Music menu are displayed with their file names or with the information from the ID3 tags. The display of ID3 tags requires that they are stored on the SD card together with the tracks.
MP3/WMA Mode Quitting Playback ➜ To quit the playback, touch the button. Playback is stopped. Selecting the Equalizer Repeated Directory Play (Repeat) You can repeatedly play all the tracks of a directory. ➜ In the Music menu, touch the More button. ➜ Touch the Repeat button. The function is activated if a check mark is displayed behind Repeat. ➜ Touch the button. The Music menu is displayed again. Various equalisers are available for the MP3/WMA mode: Normal, Classic, Rock, Pop and Jazz.
Picture Viewer Picture Viewer Removing the SD Card ➜ You quit the MP3/WMA mode by touching the button in the Music menu. ➜ Carefully push on the SD card in the slot until it disengages. The SD card is ejected a little bit and can be removed. (with Lucca MP3 only) The Lucca MP3 can also be used to view pictures that are stored on the inserted SD card. For this purpose, the pictures must be stored in the .jpg or .bmp format on the card.
Picture Viewer Starting the Slide Show If you started the Picture Viewer, the first picture in the first directory recognised by the Lucca MP3 is displayed. button to start a ➜ Touch the slide show with all the pictures in the current directory. ➜ Touch the Picture Viewer button. The Pictures menu displays. Setting the Time for the Slide Show For a slide show, you can set the display time of the individual pictures of a folder. You can select from 5, 10, 15 and 20 seconds.
Picture Viewer ➜ Touch the Slideshow button repeatedly until the desired time is displayed. button. ➜ Touch the The Pictures menu is displayed again. Selecting a Directory/Picture via File Browser ➜ In the Pictures menu, touch the More button. The menu is displayed. Quitting the Slide Show ➜ To quit the slide show, touch any position on the display. The slide show is stopped and the Pictures menu is displayed again.
Picture Viewer Selecting a Picture via Button ➜ To select the next picture in the dibutton in the rectory, touch the Pictures menu. ➜ To select the previous picture in button the directory, touch the in the Pictures menu. The next or previous picture is displayed. ➜ Touch the desired directory. The directory is displayed. ➜ Touch the picture you want to display. The Pictures menu is displayed again and the selected picture is displayed.
Picture Viewer ➜ Touch the Show Folder button. The display of the directory name is activated if a check mark is displayed. button. ➜ Touch the The Pictures menu is displayed again. Adjusting the Picture to the Display Format You can define that pictures which are stored in portrait format, are automatically rotated for maximum utilisation of the display. ➜ In the Pictures menu, touch the More button. ➜ Touch the Rotate button. The automatic rotation is activated if a check mark is displayed.
Installing Street Maps Installing Street Maps The road map of the country in which the Lucca was purchased is preinstalled in the memory of the Lucca. You can purchase additional road maps for most European countries on SD card or CD-ROM. The preinstalled road map is also contained on the enclosed CD-ROM for a future restore. To install a road map from the CDROM, copy it from the CD-ROM to an SD card and install the road map as described below.
Accessories Cradle (only Lucca MP3 is part of the scope of delivery) The cradle allows for adding additional functions to the Lucca. If you installed the cradle in your vehicle and connected it to a Blaupunkt car sound system, the following functions are available: • TMC data transfer to the Lucca with the use of a suitable car sound system (with TMC output). • Lucca power supply. • Muting the radio for travel instructions. • GALA, speed-dependent volume control. • Line out.
Accessories Connection Blocks of Blaupunkt Car Sound Systems for Lucca MP3 C-1 C 1 A 7 4 10 9 6 3 5 2 B C-2 8 C-3 16 13 15 12 11 14 1 3 5 7 2 4 6 8 1 3 5 7 2 4 6 8 A 1 nc 2 Radio Mute 3 Sub out 4 Permanent +12V 5 Aut. antenna 6 Illumination 7 Kl.
Installations Installations • (not part of the scope of delivery) Steering Wheel Remote Control RC 09 • The RC 09 steering wheel remote control allows you to operate the Lucca safely and conveniently from your steering wheel. • • • With the buttons , , and , you can move the selection mark (yellow) in the menus and lists. The button has the same function as the OK button in the lists and menus. The button is used to exit the menus and lists. It has the same function as the button.
Technical Data Warranty Technical Data Warranty TFT display Active colour matrix, 3.5 inch diagonal, 320 x 240 pixel We provide a manufacturer's warranty for our products purchased within the European Union. For devices purchased outside the European Union, the warranty terms issued by our respective responsible domestic agency are valid. The warranty terms can be called up under www.blaupunkt.
FAQ Fault Removal / Frequently Asked Questions FAQ Why does the Lucca/Lucca MP3 require GPS reception? The system must know where it is located or where it is moving. This is accomplished with the help of GPS satellites. Without GPS reception, navigating is not possible. I have bad or no satellite reception. What can I do to improve it? One obstacle could be the metalevaporated windshield or a windshield heater. The metal evaporation prevents the GPS signals from reaching the built-in antenna of the Lucca.
FAQ The built-in loudspeaker does not meet my quality demands. What can I do? The Lucca can be connected to a car sound system with Tel.-In/Aux-In, so that the loudspeakers can be used for the playback. The sound should improve significantly. The following data can be stored on the SD card: • Navigation data of other countries (depth-digitised) • MP3/WMA files for playback (Lucca MP3 only) • Pictures in the JPEG format (Lucca MP3 only).
FAQ The internal navigation software remains intact and you can use either the internal navigation software or the one on the SD card for the selection. Is the old internal navigation software overwritten with a change of the navigation software? No, the system can navigate with the internal as well as the external data. If the external data (SD card) are used for navigation, the SD slot for the MP3/WMA playback for the Lucca MP3 is unavailable during this time.
FAQ Does the connection of the remote control (RC09 available as an option) require an external infrared receiver? No. The infrared receiver is integrated in the Lucca. Which cards can I use? Commercial SD or MMC cards. We tested SanDisk and Kingston. Which data format is required for an SD card? FAT 16/32. 95 Lucca_long_2G_eng.indd 95 13.04.
Country: Phone: Fax:/www: 05121-49 4002 www.blaupunkt.com 01-610 39 391 02-525 5263 44-898 644 09-435 99236 01-4010 7320 01-89583 8394 210 94 12 711 01-46 66 706 02-369 62464 40 2085 0800 400 1040 66-817 157 2185 00165 91 410 4078 08-7501810 01-8471650 02-6130 0514 76 511 809 022-8771260 0212-346 00 40 Germany (D) 0180-5000225 Austria Belgium Denmark Finland France Great Britain Greece Ireland Italy Luxembourg Netherlands Norway Portugal Spain Sweden Switzerland Czech. Rep.