Owner's Manual
PART# BCB-2000R
TOP
CLAMP
SCREW
LOWER CLAMP/TOP
PIVOT SCREWS
Bland
ffloun
Inno
v
at
i
ve
Mounting
Solutio
ns
&
cobra
7 - Install
the
RD
onto the mount.
Make
the necessary adjustments
as
shown
above.
Using
the vertical adjustment,
we
recommend
you
adjust
the
RD
as
close
to
the
bottom of
the
mirror
as
possible.
The
spring
clip
holding
the
RD
is
designed
to
flex downward
to
allow access
to
the
RD
buttons
as
shown
below
in
step
10
.
8 - At this point your
RD
should
be
positioned where
you
want it
and
the
screws
should
be
snug. Loosen
the
top clamp screw
so
both
the lower
clamp/top pivot screws
can
be
fully tightened.
Grab
the
long
arm
of the
allen wrench
to
assure that these screws
are
securely tightened.
You
will
not strip out the
tapped
holes
in
the aircraft grade
alum
i
num
. The
bottom clamp screws should be fully tightened before tightening
the top clamp screw. If the top screw Is tightened before the
bottom screws are, the clamp will loosen over time.
REMOVING RD STEP • 1
REMOVING RD STEP
..
2
9 -
When
removing or Installing the RD, squeeze
the
trigger
and
the
back
side of
the
mount together with one hand,
and
lift
the
front of the
RD
upward
with
the
other
hand
before sliding the
RD
off or onto
the
spring clip. You must lift the front
of
the RD upward before sliding it
off
or
onto the mount.
1 O -
To
access
the
buttons of
the
RD
you
will
need
to
gently
push
downward
on
the
front of
the
RD
with one finger
and
push
the
desired button
with
another finger.
Then
allow
the
RD
to
return
to
it's origi
nal
positi
on
by
gently letting
it
spring upward.
When
accessing the buttons,
be
sure
to
push
the
RD
downward
Just
enough
for your finger
to
flt
between
the
RD
and
mirror.
Do not push down more than what is needed.
NOTE : This mount
can
get extremely hot
when
sitting
in
direct sunlight. If
you
intend
to
remove your
RD
frequently,
you
may want
to
install the two gray "
TOUCH
STRIPS" included
in
the
tool
kit.
Place
them
where your fingers
make
contact wi
th
the
mount.
They
may
be
trimmed
with
a blade or knife.
FOR MORE INFO VISIT www.blendmount.com/videos
CAUTION
DO N
OT
use this mount if it interferes
with
the
adjustability or
the
operati
on
of your rear view mirror
in
any
way
.
DO NOT
use
this mount if the radar detector creates
an
unsafe viewing obstruction.
DO NOT
ATTEMPT
TO
MODIFY
THIS
PRODUCT. Consult
the
manufacturer for assistance.
All
Blend
Mo
Jnt
products
are
accompanied with detailed installation instructions
and
adjustment tips.
You
are encouraged
to
contact customerser
1ice@blend
-
mount.com or
call
J28
Design at 1-888-497-8388 for further assistance.
Check the BlendMount
Forum
for installation
tips
and
some
vehicle specific installs.
www
.blendmount.com
lnnov ti~ De ign
And
Preci
Ion
M
n~
cturing
PAGE20F2
Your
feedback
is
very important
to
us.
Please email any questions or
comments
you
have
to
customerservice@blendmount.com
BlendMount - US PATENT# 0625,
580
S,
D656,811
S, 0653,980 S
0690,245 S,
D690
,246 S, D690,247 Sand other patents
pend
i
ng