Full Face Bluetooth® Integrated Helmet BLINC BLUETOOTH USER MANUAL ® ™ O’Neal Distributing Inc., 685 Cochran St. Simi Valley, CA 93065 USA Made in China www.oneal.com or www.oneal.
® Introduction BLINC™ III Bluetooth Profile HFP (Hands-free Profile) The BLINC™III integrated helmet communications system is based on Bluetooth® wireless technology. Bluetooth® wireless technology is a short-range radio communication technology intended to replace the cables connecting electronic devices.The technology uses a globally available frequency range intended to ensure communication compatibility worldwide.
Getting Started To start using your BLINC™III headset: 1. Charge the BLINC™III battery. 2. Learn the functions of the control unit. 3. Pair the BLINC™III headset with a device, for example, a mobile phone. Charging Port Cover Figure 1 Charging The headset comes with a built-in rechargeable battery.We recommend that you charge the battery before using the headset for the first time. Connect the charger to the charging port on the control unit (Figure 1) and plug the charger into your wall outlet.
® Headset Control Unit Blinc™ lll Bluetooth VOL– : Volume Decrease (turn counter clockwise) ™ III Headset OFF Turning the BLINC VOL+: Volume Increase (turn clockwise) Press and hold the Multi-Function Button (MFB) for approximately 5 seconds until you hear a short high tone followed by a short low tone.The display screen will show “BLINC OFF.
™ To pair the BLINC III Headset with a Phone or Another Device Phone Set-up/Pairing Tips On the phone enter the “searching for Bluetooth® device mode” and press and hold the Multi-Function Button (MFB) on the helmet control unit for approximately 5 seconds until “Pairing” is displayed on the screen. The BLINC™III headset password/PIN is 0000. If pairing is successful the display will show “Pairing End” and the phone icon. Pairing should be done only once.
™ How to use BLINC III with Your Mobile Phone 1.To answer a call. When the BLINC™III headset rings, press the Multi-Function Button (MFB) on the helmet control unit to answer the incoming call. 6.To transfer the sound back to your mobile phone. During a call using your BLINC™III headset, press the Multi-Function Button (MFB) for approximately 2 seconds. If your BLINC™III headset works with Headset Profile, you just need turn down your BLINC™III headset. 2.To terminate a call.
Pairing Helmets for BLINC ™ III Intercom 1. Before pairing, make sure there is no Bluetooth ® device active in your area. 2.Turn on the RIDER Bluetooth. ® 2. Press the control Button to turn on the RIDER Bluetooth unit, release the button and wait until the display shows, "BLINC ON," and then shows, "BLINC." Turn and hold the Control Button counter or clockwise for 3-4 second on the RIDER Bluetooth Helmet.The display will first show “FM Radio On.
How to Make Intercom Calls How to Use Bluetooth FM Radio Function RIDER. If not on an active phone call, press the Multi-Function Button (MFB), the headset will now enter the Turn FM ON. Headset idle status, turn and hold the Multi-Function Button (MFB) counterclockwise about 2 Intercom mode.The RIDER headset will initiate an intercom call to the last paired headset automatically. Press the MFB to terminate the call.
BLINC™III System Reset Disclaimer To reset the Control Unit, use the supplied Reset Key. Simply insert it into the Charging Port to reset the system. MANUFACTURER IS NOT LIABLE FOR INJURIES DUE TO MISHANDLING OF THE DEVICE. ALWAYS ATTACH AND FASTEN THE HELMET PROPERLY AND RESPECT SPEED LIMITS & WEATHER WARNINGS. Bluetooth® Interference Issues The quality of Bluetooth® transmission may also be affected by the position of your connected device.
BLINC ™ III 90-day Limited Warranty To obtain repairs or replacement within the terms of this warranty, please visit www.oneal.com or contact us at 685 Cochran St. Simi Valley, CA 93065. Proof of warranty coverage (i.e. - dated bill of sale) is required. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES OR LIABILITIES. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY.
BLINC ™ III 90-day Limited Warranty, continued No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product. Some jurisdictions do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you.
NOTES For more information visit www.oneal.