Owner's manual

ManualsBrandsBlinds Chalet ManualsFor HomeSilverscreen Roller Shades - 4%

Extension Brackets (optional for Headrail shades)

Optional Extension Brackets are used to project the back of the

shading up to 2 1/2" from the mounting surface. Attach the Standard

Mounting Bracket to the Extension Bracket with the nut and bolt

provided.

Side Mount

(optional for Headrail shades)

Measure from window sill up to desired mounting position on each

side of the window frame. Mark position. Mount Side Mount Brackets

on each side of window frame as shown. Make sure to confirm that

headrail will sit perfectly level. Once Side Mount Brackets are

installed and properly positioned, attach the Standard Mounting

Brackets using the nuts and bolts provided.

Step 2. HANGING THE SHADE

Shades with NO Headrail or Fascia

Once the brackets are secured and level, the fabric roll can be

inserted. Make sure your hands are clean to avoid soiling the fabric.

While facing the inside of the shade, be sure the clutch and roller end

plug are inserted into the roller. Hold the

shade with the bottom of the clutch facing

the floor, and the beaded cord hanging

straight down.

Insert the foot of the control-

side bracket into the slotted

center hole of the clutch. Set

nub of the end plug into the V

of the support bracket.

Rotate the T-hook on the

support bracket to engage

over the nub on the idler and

secure the fabric roll.

Inside Mount - Fascia or NO Headrail

Inside Mount with Headrail

Fully Recessed Inside Mount with Deluxe Headrail

Out

side Mount - Fascia or NO Headrail

Outside Mount - with Headrail

Extension and Sidemount - NO Headrail

The standard roller brackets can be mounted to the side of any

opening utilizing the holes in the side of the bracket.

The optional Extension roller brackets mount in the same manner as

above, but allow an extra 1/2” of projection for the roller.

BASICS

A few simple tools are required:

- Measuring tape

- Carpenters Level

- Power drill or Phillips head Screwdriver

- ¼" Hex head and/or Phillips driver bit

Additional fasteners other than those sent with your shading may be

required depending on the mounting surface. Wallboard and plaster require

the use of anchors such as expansion or toggle bolts. Brick, tile or stone

need special plugs and drill bits. Remember to always pre-drill holes in

wood to avoid splitting.

Step 1. BRACKET INSTALLATION

For shades with headrail, the End brackets

should be located with centerlines 2" in from

each end. Depending on the width of the

shading, necessary additional brackets may

be evenly spaced between the two end

brackets.

For shades with NO headrail, the installation brackets are always

mounted so that the inner surfaces face each other. For Shades with

a fascia, the brackets are mounted with the open end down. It is very

important that the

brackets are

mounted so that

the shade is level

when installed.

1 1/4” Hex

Head

Bracket

Screw

Deluxe

Mounting

Bracket

Wedge for Deluxe

Headrail Bracket

Headrail Extension &

Side mount Bracket

Nut &

Bolt

“U” Shim for

Headrail bracket

Hold Down Bracket

(optional)

Hold Down

Bracket Screw

If the headrail or roller does not sit level, the fabric will not roll up

evenly which could damage the edges of the shading fabric.

Mount roller brackets as necessary, or use shims for headrail

shades if necessary to level brackets.

Low light gap wedges can be used to reduce the

top light gap when the shade is mounted fully

recessed. The wedge is placed between the

mounting surface and the bracket with the tabs

on the wedge facing down and the thick end of

the wedge toward the back of the bracket.

3/4” minimum surface

Shade width # Brackets

Up to 40” 2

>40” - 72” 3

>72” - 84” 4

>84” - 114” 5

Roller Mounting

Brackets for NO Headrail

The roller brackets

can be mounted up

against the window

frame, or back

against the window

casing.

Foot

T-Hook

The roller brackets

can be mounted

back against the

window casing, or

up against the

ceiling.

Control Side

Bracket

End Plug Side

Bracket

Nub

Support Bracket

Ultra Sleek

Mounting

Bracket

3/4” minimum surface

2 1/2”

2” minimum surface required

Position screw in center of slot

so you can adjust position of

bracket as necessary.

Ultra Sleek Deluxe

1” minimum for

shallow mount

2 7/8” minimum for

flush inside mount

Use shims if necessary to ensure that the headrail is mounted level (included).

3/4” minimum for

shallow mount

3 3/4” minimum for

flush inside mount

2”

Brackets for Roller

Shades with Fascia

T-Hook

Control Side

Bracket

End plug Side

Bracket

No Headrail

bracket pictured

Ultra Sleek Deluxe

Fascia

No Headrail

Fascia

No Headrail

Ultra Sleek

Deluxe

Summary of content (2 pages)

PAGE 1
BASICS Inside Mount - Fascia or NO Headrail A few simple tools are required: - Measuring tape - Carpenters Level - Power drill or Phillips head Screwdriver - ¼" Hex head and/or Phillips driver bit Ultra Sleek “U” Shim for Wedge for Deluxe Headrail bracket Headrail Bracket 1 1/4” Hex Head Bracket Screw 2” 2 7/8” minimum for flush inside mount 3/4” minimum for shallow mount 3 3/4” minimum for flush inside mount Use shims if necessary to ensure that the headrail is mounted level (included).
PAGE 2
Shades WITH Headrail Ultra Sleek Step 5. HOLD DOWN INSTALLATION (optional) Deluxe Push the rail back until it is fully engaged. Un-Install Headrail Ultra Sleek Deluxe To remove the shading, partially lower the shading and insert a flat head screwdriver as shown. Twist the screwdriver until the headrail disengages from the bracket. Step 3. ATTACHING FASCIA PANEL (IF ORDERED) Attach the fascia by first hooking the top lip of the fascia panel onto the bracket as shown.