ADJUSTABLE BASE USER MANUAL Please read and keep for future reference. This manual contains important safety information.
TABLE OF CONTENTS ..............................................4 KD2 HEADBOARD FOOTBOARD BRACKET INSTALLATION ................ 12 WEIGHT RESTRICTIONS AND EMERGENCY BACKUP ..........................5 REMOTE ASSEMBLY AND FREQUENCY SET UP .................................13 ...............................................................................6 REMOTE CONTROL SYNCHRONIZING TWO ADJUSTABLE BASES .........14 IMPORTANT SAFETY INFORMATION FEATURES GETTING STARTED .................................
IMPORTANT SAFETY INFORMATION PLEASE READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE USE AND ASSEMBLY SAFETY INFORMATION Only use the adjustable bed base for its intended use as described in this manual. Follow the guidelines below for your safety, the safety of others and to avoid risk of electrical shock, fire, burns or injury: • Avoid fingers in pinch-points. • Two or more adults is strongly recommended for moving and assembling of the adjustable bed base.
WEIGHT RESTRICTIONS The recommended weight restriction for the adjustable base is 750 pounds, which is calculated to include the weight of the mattress. To calculate the weight limit, subtract the weight of the mattress from 750 pounds. The bed will support the recommended weight limits if distributed evenly across the base. This product is not designed to support or lift the total maximum weight limit by the head or the foot section only.
FEATURES • • • • • Head and foot up/down positions 5 button wireless remote control Pre-programmed flat position Six legs with customizable heights Undercarriage is made with reinforced steel components for strength and durability • Emergency backup battery box • Mattress foot retainer bar CONTACT OUR COMFORT CONCIERGE TO PURCHASE ACCESSORIES • Head and footboard brackets Note: This base is designed to fit within a standard bedframe.
GETTING STARTED (1x) Back-Up Battery pack NO TOOLS REQUIRED FOR ASSEMBLY. Use caution at pinch points and unfolding the base as parts may have shifted during shipping.
POWER CORD SETUP CAREFULLY open the adjustable bed base into an L position on its side or lay flat with the bottom facing up. This step may require two adults for safety. (1x) Back-Up Battery pack (1x) AC/DC Power Adapter per Base Ensure all power cord connections circled to the right are completely plugged-in. Installation of the Backup Battery Pack is optional. Only put batteries into the Backup Battery Pack during an electrical outage and after the power cord is unplugged from a power source.
JOINING TWO ADJUSTABLE BASES If any split setup is being installed, plastic connecting straps are provided (one per base) to secure the bases together. Use both straps to secure the head and foot portions together. With the bases in their desired location, slightly loosen both legs to allow the strap to fit on the leg bolt, between the leg washer and frame. (A) (B) PAGE 9 JOINING TWO ADJUSTABLE BASES Slide side (A) of the connecting strap onto leg bolt.
LEG ASSEMBLY Locate the legs and choose one of the heights. Make sure the leg with the solid end is touching the floor. Screw six legs into the pre-drilled holes by hand. All legs must be installed and resting evenly on the floor. The base will not operate properly without the legs. PAGE 10 LEG ASSEMBLY The legs must be a minimum of 6” to maintain articulating clearance and must not exceed 12”; anything taller is considered unstable.
MATTRESS RETAINER BAR ASSEMBLY Locate the mattress retainer bar in the packaging. At the foot of the base, there are two openings to insert the mattress retainer bar. Slide the large retainer bar into the opening at the foot of the bed. Figure 1 PAGE 11 MATTRESS RETAINER BAR ASSEMBLY Secure the retainer bar (Figure 1) with the included wing-nuts (Figure 2). This will hold the mattress retainer bar in place.
KD2 HEADBOARD & FOOTBOARD BRACKET Recommended Tools • Socket Wrench • Crescent Wrench *Optional Accessory Included (8x) Nut (8x) Washer Figure 1A 1 (8x) Long Bolt (8x) Short Bolt PAGE 12 HEADBOARD & FOOTBOARD BRACKET (2x) Side Bracket 1 (2x) Side Bracket 2 Figure 2A Figure 1B Carefully place the base flat (Figure 1A) or in a side L position (Figure 1B).
REMOTE ASSEMBLY AND FREQUENCY SET UP Locate the wireless remote control and insert (3x) AAA batteries (included). The remote control is pre-programmed to work with the adjustable bed base. If you have more than one adjustable bed base, each remote control and adjustable bed base set should be pre-programmed to work separately.
REMOTE CONTROL SYNCHRONIZING TWO ADJUSTABLE BASES Step 1: Unplug base from power source. Step 2: Connect the male end of the simultaneous synchronization cable to each control box, only one sync cord is required. Step 3: Plug base back into the power source. Step 4: Check to ensure all cords are securely attached. Both remotes will now operate both bases simultaneously.
REMOTE CONTROL FEATURES Head Up Head Down Foot Up Foot Down Flat Position PAGE 15 REMOTE CONTROL FEATURES
FAQ Will the adjustable base fit inside my current bed frame? Yes, we designed the adjustable base width and length to be ½” shorter than standard bed sizes to ensure the base fits within most* bed frames. Even if you have a headboard and footboard with side rails and slats, our adjustable base will fit right in place.
TROUBLESHOOTING GUIDE If one or more functions on the base have stopped operating: • Check under the bed base to verify that the wired connections are secure and that there are no cords or bedding obstructing the movement of the base. • Check that the power cord is assembled properly and that the connections are secure. • Check if green LED is on (power supply).
COMPONENT GUIDE Head Actuator Master Control Box Foot Actuator PAGE 18 TROUBLESHOOTING COMPONENT GUIDE
10 YEAR LIMITED WARRANTY FULL 1-YEAR WARRANTY The Adjustable Base is warranted against defects in materials or workmanship for a period of one year from the date of purchase to the original purchaser. During the first year, manufacturer will repair or replace, at no cost to the original purchaser, any defective part. This includes all authorized labor and transportation costs incurred with the repair or replacement of any parts found to be defective.