Blizzard Lighting, LLC www.blizzardlighting.
TABLE OF CONTENTS The Puck CSI™ Xtreme LED PAR Can 1 1. Getting Started 3 What’s In The Box? 3 Getting It Out Of The Box 3 Powering Up! 3 Getting A Hold Of Us 3 Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4 2. Meet The Puck CSI™ Xtreme LED PAR Can 5 Features 5 DMX Quick Reference 5 The Puck CSI™ Xtreme Pin-up Picture 6 3.
1. GETTING STARTED What’s In The Box? • 1 x Puck CSI™ Xtreme UV LED PAR Fixture • 1x IEC Power Cord • This Lovely User Manual Getting It Out Of The Box Congratulations, aspiring crime fighter and/or psychedelic music aficionado! Now that you’ve got The Puck CSI™ Xtreme (or hopefully, Xtreme’s!), you should carefully unpack the box and check the contents to ensure that all parts are present and in good condition.
SAFETY INSTRUCTIONS • Please keep this User Guide for future use. If you sell the unit to someone else, be sure that they also receive this User Guide. • ALWAYS make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture. • This product is intended for indoor use only. • To prevent risk of fire or shock, do not expose fixture to rain or moisture.
2.
Figure 1: The Puck CSI™ Pin-Up Picture 36x 3-watt UV LEDs Dual Mounting Yokes Ridiculously Thin! Figure 2: The Rear Connections DMX In LED Control Panel DMX Out Microphone Page 6 The Puck CSI Xtreme User Manual Rev.
3. SETUP Fuse Replacement With a flat head screwdriver, wedge the fuse holder out of its housing. Remove the damaged fuse from its holder and replace with exact same type fuse. Insert the fuse holder back in its place and reconnect power. Connecting A Bunch of Puck CSI™ Xtreme Flat LED PAR Cans You will need a serial data link to run light shows using a DMX-512 controller or to run shows on two or more fixtures set to sync in master/slave operating mode.
Cable Connectors Cables must have a male XLR connector on one end and a female XLR connector on the other end. (Duh!) CAUTION: Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.
Fixture Linking (Master/Slave Mode) 1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first fixture. 2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then, proceed to connect from the output as stated above to the input of the following fixture and so on.
USING THIS FIXTURE WITH THE wiCICLE® WIRELESS DMX SYSTEM In addition to the unbridled thrill you already received the first time you plugged in your fixture, you’ll be delighted to know that This fixture also works seamlessly with our wiCICLE® Wireless DMX system, without additional power. • ONLY fixtures bearing this logo are certified for use with the wiCICLE® without external power. • Unauthorized modification and/or using the wiCICLE® with unapproved fixtures may cause damage to the wiCICLE® or fixture.
Each wiCICLE® acts as both a transmitter and a receiver, depending on whether a DMX source is applied to the integral XLR connector. This is an extremely powerful feature of the system, however, it also requires 1 piece of due dilligence, and that is the removal of extraneous DMX signals from your lighting rig BEFORE proceeding.
4. OPERATING ADJUSTMENTS The Control Panel All the goodies and different modes possible with the Puck™ CSI Xtreme are accessed by using the control panel on the rear of the fixture. There are 4 control buttons below the LED display which allow you to navigate through the various control panel menus.
DMX Mode Allows the unit to be controlled by any universal DMX controller. 1. To set the fixture to run in 4-channel DMX mode, use the
5. APPENDIX Keeping Your Puck CSI™ Xtreme As Good As New The fixture you’ve received is a rugged, tough piece of pro lighting equipment, and as long as you take care of it, it will take care of you. That said, like anything, you’ll need to take care of it if you want it to operate as designed. You should absolutely keep the fixture clean, especially if you are using it in an environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled drinks.
Tech Specs Weight & Dimensions Length 8.25 inches (210 mm) Width 3.875 inches (98.43 mm) Height 8.5 inches (215.9 mm) Weight 4.2 lbs (1.3 kg) Power Operating Voltage 110-230VAC, 50-60 Hertz Power Consumption 108W Light Source LED 36x 3w 390-410nm UV LEDs Optical Beam Angle 25 degrees, 29 degree field Thermal Max. Operating Temp.
Enjoy your product! Our sincerest thanks for your purchase! --The team @ Blizzard Lighting