Blizzard Lighting, LLC www.blizzardlighting.
TABLE OF CONTENTS The Puck™ V12 1 1. Getting Started 3 What’s In The Box? Getting It Out Of The Box Powering Up! Getting A Hold Of Us Safety Instructions (Don’t Stick Your Hand In The Toaster!) 3 3 3 3 4 2. Meet The Puck™ V12 5 Main Features Optical Specs Luminous Intensity Chart The Puck™ V12 Pin-up Picture 5 5 5 6 3.
1. GETTING STARTED What’s In The Box? • 1 x Puck™ V12 Professional LED PAR Fixture • This Lovely User Manual Getting It Out Of The Box Congratulations on purchasing one of the coolest professional LED Par fixtures anywhere! Now that you’re the proud owner of a Puck™ V12 (or hopefully, V12’s!), you should carefully unpack the box and check the contents to ensure that all parts are present and in good condition.
SAFETY INSTRUCTIONS • Please keep this User Guide for future use. If you sell the unit to someone else, be sure that they also receive this User Guide. • ALWAYS make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture. • This product is intended for indoor use only. • To prevent risk of fire or shock, do not expose fixture to rain or moisture.
2.
Figure 1: The Puck™ V12 Pin-Up Picture Ridiculously thin! 5-in-1 RGBWAColor LED’s Dual Mounting Yokes Figure 2: The Rear Connections DMX In LED Control Panel The Puck™ V12 Manual Rev.
3. SETUP Fuse Replacement CAUTION! The Puck™ V12 utilizes a high-output switch-mode power supply with an internal fuse. Under normal operating conditions, the fuse should not require replacement. The fuse is field replaceable, however it is an advanced procedure suited to qualified individuals. Should your The Puck™ V12 fuse require replacement, please contact Blizzard Lighting for instructions, or to return your unit for service.
Cable Connectors Cables must have a male XLR connector on one end and a female XLR connector on the other end. (Duh!) CAUTION: Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.
Fixture Linking (Master/Slave Mode) 1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first fixture. 2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then, proceed to connect from the output as stated above to the input of the following fixture and so on.
4. OPERATING ADJUSTMENTS The Control Panel All the goodies and different modes possible with The Puck™ V12 are accessed by using the control panel on the rear of the fixture. There are 4 control buttons below the LED display which allow you to navigate through the various control panel menus.
Control Panel Menu Structure DNH 1 - 512 PERS STAG ARC.1 AR1.d ARC.2 AR2.d AR2.S HSV Id Id.01 - Id.
DMX Allows the unit to be controlled by a universal DMX controller. To select a different DMX address, hit the button and use the buttons to select the correct address. Hit
2.) ARC.1 - Architectural Mode 1 (RGB, 3-Ch.) Channel Value 1 000 <--> 255 Red Intensity (0% <--> 100%) 2 000 <--> 255 Green Intensity (0% <--> 100%) 3 000 <--> 255 Blue Intensity (0% <--> 100%) 3.) AR1.d What It Does - Architectural Mode #1 w/dimming (RGB, 4-Ch.) Channel Value 1 000 <--> 255 Master Dimmer (0% <--> 100%) 2 000 <--> 255 Red Intensity (0% <--> 100%) 3 000 <--> 255 Green Intensity (0% <--> 100%) 4 000 <--> 255 Blue Intensity (0% <--> 100%) 4.) ARC.
6.) AR2.S - Architectural Mode #2 w/strobe (RGBAW, 7-Ch.) Channel Value 1 000 <--> 255 Master Dimmer (0% <--> 100%) 2 000 <--> 255 Red Intensity (0% <--> 100%) 3 000 <--> 255 Green Intensity (0% <--> 100%) 4 000 <--> 255 Blue Intensity (0% <--> 100%) 5 000 <--> 255 Amber Intensity (0% <--> 100%) 6 000 <--> 255 White Intensity (0% <--> 100%) 7 000 <--> 255 Strobe 7.) HSV What It Does - Hue, Saturation, Value (3-Ch.
EdIT Edit Scenes & Programs Create/edit up to 10 programs of up to 30 scenes for playback in standalone mode, (from the “Auto” menu).
•• RGBU Enables/disables RGBW color correction. •• POU Sets the fixture in “Normal” (Low Power, 33% output) or “High” power mode. •• DIN Sets the 16-bit dimming curve (OFF=8-bit (standard) dimming, 1-4 are 16bit dimming profiles, fastest to slowest). CAL1 Color Temperature-Based White Values This menu option allows the user to set the fixture’s white output to one of 11 preset or user adjustable color temperatures.
STAT Static Color Display + Strobe Allows you to display a static custom color using RGBAW color values. Hit and then use the and buttons to select the desired R/G/B/A/W value you want to edit. Hit . Use the and buttons to change the desired value. Then push the
Troubleshooting Symptom Solution Fixture AutoShut Off Check the fan in the fixture. If it is stopped or moving slower than normal, the unit may have shut itself off due to high heat. This is to protect the fixture from overheating. Clear the fan of obstructions, or return the unit for service. Beam is Dim Check optical system and clean excess dust/grime. Also ensure that the 220V/110V switch is in the correct position, if applicable.
5. APPENDIX A Quick Lesson On DMX DMX (aka DMX-512) was created in 1986 by the United States Institute for Theatre Technology (USITT) as a standardized method for connecting lighting consoles to lighting dimmer modules. It was revised in 1990 and again in 2000 to allow more flexibility. The Entertainment Services and Technology Association (ESTA) has since assumed control over the DMX512 standard. It has also been approved and recognized for ANSI standard classification.
Keeping Your The Puck™ V12 As Good As New The fixture you’ve received is a rugged, tough piece of pro lighting equipment, and as long as you take care of it, it will take care of you. That said, like anything, you’ll need to take care of it if you want it to operate as designed. You should absolutely keep the fixture clean, especially if you are using it in an environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled drinks.
Tech Specs! Weight & Dimensions Length 8.25 inches (210 mm) Width 3.875 inches (98.43 mm) Height 8.5 inches (215.9 mm) Weight 4.2 lbs (1.92 kg) Power Operating Voltage 100-240VAC, 50-60 Hertz Power Consumption 120W Light Source LED 12* 15-watt 5-in-1 LEDs, 100,000 hours Optical Beam Angle 25°, Field Angle: 29° Thermal Max. Operating Temp.
This page intentionally left blank. The Puck™ V12 Manual Rev.
This page intentionally left blank.
Enjoy your product! Our sincerest thanks for your purchase! --The team @ Blizzard Lighting
