July 15, 2012 Lit. No. B64092, Rev. 06 Models 760TR, 810TR, 8100TR, 860TR, 8600TR & 8611TR Installation Instructions & Owner's Manual CAUTION See your BLIZZARD sales outlet/Web site for specific vehicle application recommendations before installation. CAUTION Read this document before installing the snowplow. CAUTION Read this document before operating or servicing snowplow. This manual supersedes all editions with an earlier date.
TABLE OF CONTENTS PREFACE.................................................................... 4 REMOVING FROM STORAGE & LIFTING ............. 27 SAFETY INFORMATION ............................................ 5 OPERATION ............................................................... 8 TECHNICAL SPECIFICATIONS & CENTER OF GRAVITY INFORMATION ............... 28 810TR, 8100TR & 8611TR .................................... 8 810TR, 8100TR & 8611TR ..................................
PREFACE PREFACE AUTHENTIC PARTS AND ACCESSORIES Congratulations on purchasing the most advanced snowplow available! The POWER PLOW™ snowplow is clearing new trails for innovative design, rugged durability, quality craftsmanship and superior performance. SPEEDWING™ blades create a whole new category for multi-position truck-mounted snowplows. Our innovative products are tested all across the snowbelt. Your BLIZZARD snowplow is a valuable investment.
SAFETY SAFETY DEFINITIONS WARNING/CAUTION & INSTRUCTION LABELS WARNING Become familiar with and inform users about the warning and instruction labels on the back of the blade. Indicates a potentially hazardous situation that, if not avoided, could result in death or serious personal injury. NOTE: If labels are missing or cannot be read, see your sales outlet. CAUTION Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury.
SAFETY Blade Serial Number Label WARNING Do not exceed vehicle operative capacity including the blade. See vehicle rating label. Blizzard PO BOX 245038 Milwaukee, WI 53223 NNNNNNNNNNNNNNNNNNNNNNNNNNNN YYMMDDLLXXXXZZZZZ YYMMDDLLXXXXZZZZ WARNING Never stand, work or reach under lift arms or lift cylinders without employing a lift arm stop or stand.
SAFETY VENTILATION FUSES The electrical and hydraulic systems contain several blade-style automotive fuses. If a problem should occur and fuse replacement is necessary, the replacement fuse must be of the same type and amperage rating as the original. Installing a fuse with a higher rating can damage the system and could start a fire. WARNING Vehicle exhaust contains lethal fumes. Breathing these fumes, even in low concentrations, can cause death.
OPERATION – 810TR, 8100TR & 8611TR MODELS Your POWER PLOW™ snowplow is the most advanced and versatile snowplow on the market. The snowplow blade and wings can be adjusted into an infinite number of plowing positions. Review the illustrations below to determine the best position for your plowing needs. WARNING Never use the snowplow attachment to carry people, as a man lift or as a work platform. WARNING When plowing with down pressure, do not cause the front wheels on the tractor to raise above ground.
OPERATION – 760TR, 860TR & 8600TR MODELS Your SPEEDWING™ snowplow is the newest multi-position snowplow on the market. The snowplow blade can be adjusted into a variety of plowing positions. Review the illustrations below for instruction on maneuvering your snowplow. WARNING Never use the snowplow attachment to carry people, as a man lift or as a work platform. WARNING A. When plowing with down pressure, do not cause the front wheels on the tractor to raise above ground. A.
UNPACKING & INSPECTION Your snowplow has been packaged to withstand transit and weather related damage. Fully inspect all components upon receipt of your snowplow. In the event of shipping damage or missing parts, immediately contact our Customer Support Department at 1-888-680-8600. Once you have inspected all parts and removed all packaging materials, your snowplow is ready to be fully assembled. Retain this information for your records.
TORQUE SPECIFICATIONS TORQUE CHART CAUTION Read instructions before assembling. Fasteners should be finger tight until instructed to tighten according to the torque chart. Use standard methods and practices when attaching snowplow including proper personal protective safety equipment.
TORQUE SPECIFICATIONS 37° JIC Flare Torque Values Turns Size ft-lb Assembly Steps min–max N/A N/A 2 2 1-1/2 1-1/2 1-1/2 1-1/4 1 1 1 1 1 -02 -03 -04 -05 -06 -08 -10 -12 -14 -16 -20 -24 -32 6–7 8–9 11–12 14–15 18–20 36–39 57–63 79–88 94–103 108–113 127–133 158–167 245–258 1. Make sure the tubing and threads are clean. 2. Lubricate the threads with 10W hydraulic fluid. 3. Hand tighten the nut/sleeve to approximately 30 in-lb. 4. Make alignment marks on the nut and fitting. 5.
MOLDBOARD & A-FRAME ASSEMBLY – 810TR, 8100TR & 8611TR MODELS 1. Remove dust cap from both of the slide box cylinders located at the center/rear of the moldboard. Attach adapters (B60007 for 810TR; 56695 for 8611TR) to both ports on each slide box cylinder. Tighten fittings per torque chart. 3. Position the front (top) hole in the A-frame with the middle hole in the pivot beam. Insert cap screw (50605) through the top, and secure on the bottom with washer (B61203) and nut (B61008). 4.
MOLDBOARD & A-FRAME ASSEMBLY – 810TR, 8100TR & 8611TR MODELS 5. Position the pivot beam between the two support ribs until the connecting points on the beam align with those on the snowplow. Insert one 3/4" x 3" clevis pin (B50069) through each mounting hole and secure them with 1/4" x 1-1/2" cotter pin (90601). 7. Hook each extension spring to the receiving holes on the pivot beam and attach the opposite end of the spring to its respective spade bolts.
MOLDBOARD & A-FRAME ASSEMBLY – 810TR, 8100TR & 8611TR MODELS 9. Assemble the manifold. Each of the hose ports on the manifold is covered with stretch wrap. Remove the wrap and install adapter (56695) in ports #1, 2, 7, 8, 9 and 10. Tighten fittings per torque chart. NOTE: When handling the manifold, hold the manifold at the sides of the block. Never handle the manifold by coils. Doing so can cause a solenoid cartridge to bend, causing the cartridge to stick when activated. 12.
MOLDBOARD & A-FRAME ASSEMBLY – 760TR, 860TR & 8600TR MODELS 1. Position the front (top) hole in the A-frame with the middle hole in the pivot beam. Insert cap screw (B61331 for 760TR; 50605 for 860TR and 8600TR) through the top, and secure on the bottom with washer (B61203) and nut (B61008). For 8600TR model: Insert one bushing (42410) through each mounting hole and secure it with a 3/8' x 1-1/2" cap screw (66439) and 3/8" locknut (91333). 2.
MOLDBOARD & A-FRAME ASSEMBLY – 760TR, 860TR & 8600TR MODELS 9/16" 9/16" 3/4" 9/16" 9/16" B60403 • Manifold Ports 40571 • Angle Cylinders 4. Hook each extension spring to the receiving holes on the pivot beam and attach the opposite end of the spring to its respective spade bolts. Install the spade bolts through the extension spring mounting angle on the top rear of the blade. Secure each spade bolt by placing one 5/8" flat washer on the bolt and thread one 5/8" locknut.
MOLDBOARD & A-FRAME ASSEMBLY – 760TR, 860TR & 8600TR MODELS 6. Assemble the manifold. Each of the hose ports on the manifold is covered with stretch wrap. Remove the wrap and install adapter (B60403) in both ports. Tighten fittings per torque chart. 10. Reinstall A-frame cover by aligning the holes in the cover with those on the A-frame and securing it with 3/8" x 1-1/2" cap screws and 3/8" washers. 11.
GENERAL SYSTEM SCHEMATICS – 810TR, 8100TR & 8611TR MODELS ELECTRICAL SCHEMATIC To Tractor Wiring S1 S2 S3 HYDRAULIC SCHEMATIC LEFT SLIDE BOX RIGHT SLIDE BOX RIGHT ANGLE LEFT ANGLE 8 7 1 2 3000 PSI 1500 PSI (2650 PSI) RV2 1700 PSI (2800 PSI) 9 10 1500 PSI (2650 PSI) 1700 PSI (2800 PSI) RV3 RV5 RV1 RV4 S1 T S3 S2 P2 P3 NOTE: Where applicable, Model 8611 values are in parentheses. Lit. No. B64092, Rev.
HYDRAULIC GUIDE – 810TR, 8100TR & 8611TR MODELS RV1 Recommended for machines equipped with auxiliary hydraulics having a flow rated at 4–30 gallons per minute (gpm) and a maximum pressure rating of 3,000psi.
OSCILLATING PLATE ASSEMBLY – ALL MODELS 1. Attach the oscillating plate to the tractor now. The tractor-specific hooks come pre-welded on the oscillating plate assembly. Refer to the illustrations below for hook identification. If welding the tractor-specific hooks is necessary, measure the distance on the tractor to determine appropriate placement of the hooks on the oscillating plate. Refer to the illustration below for weld specifications. 2.
ELECTRICAL INSTALLATION – 810TR, 8100TR & 8611TR MODELS 2. Connect the tractor end of the coil harness to the tractor's auxiliary electrical system according to the vehicle's owner's manual or service manual. NOTE: 760TR, 860TR and 8600TR Models do not require electrical connections between the tractor and the snowplow. 1. 3. Complete the assembly by reattaching the A-frame cover. Align the holes in the cover with those on the A-frame and secure it with 3/8" x 1-1/2" cap screws and 3/8" washers.
MOUNTING & DISMOUNTING INSTRUCTIONS – ALL MODELS Prior to operating your snowplow, review the Mount and Dismount Instructions label on the back of the driver-side moldboard. NOTE: If at any time the Mount and Dismount Instructions label, or any other label attached to your snowplow, becomes illegible, promptly replace it. MOUNT INSTRUCTIONS DISMOUNT INSTRUCTIONS Read Owner's Manual for Complete Instructions. Read Owner's Manual for Complete Instructions.
TESTING YOUR SNOWPLOW – ALL MODELS 1. To test all of the functions, your snowplow needs to be properly attached to the tractor. Refer to the Mounting and Dismounting label on the back of the snowplow. NOTE: Depending on the tractor model, it may be necessary to turn ON the tractor's auxiliary hydraulic switch prior to operating the snowplow. Activate each function of the snowplow. 2. Complete the hydraulic connections with the tractor turned OFF.
ADJUSTABLE SNOWPLOW SHOE ASSEMBLY – ALL MODELS WARNING Blade can drop unexpectedly. Place the blade on jack stands. Failure to do so could result in serious personal injury. With the snowplow fully assembled and operational, install the adjustable plow shoes. 1. 5/16" Locknut 5/16" x 1-3/4" Cap Screw Raise the snowplow 6" to 12" off the ground, turn the tractor OFF and, from in front of the blade, place jack stands or sturdy blocking under the cutting edge. 3/4" Washer 2.
MAINTENANCE – ALL MODELS Maintenance Periodically Check fasteners for tightness. Torque to specifications. X Check hoses for wear and leaks. X Check cylinders for leaks; inspect rod ends for corrosion & pitting. X Check cables for wear or fraying (760TR and 860TR Models only). X Lubricate all exposed cylinder rod ends with liquid white lithium grease to prevent corrosion. Check cutting edges and plow shoes for wear. X Clean and lubricate all electrical plugs and connections with dielectric grease.
REMOVING FROM STORAGE & LIFTING REMOVING FROM STORAGE LIFTING 1. To lift and move this snowplow, attach chain fall grab hooks to outside pivot beam area shown. Always follow recommended lift warnings and procedures. See the following page for snowplow weights and dimensions. Perform all regular maintenance. 2. Replace the hydraulic fluid in the hydraulic system. Prolonged storage could result in condensation build-up. 3. Follow the mounting procedure on the Mounting and Dismounting label. 4.
TECHNICAL SPECIFICATIONS & CENTER OF GRAVITY INFORMATION 810TR, 8100TR & 8611TR MODELS Part Moldboard Wings A-Frame Manifold Cylinders Snowplow Specs Specification Length Thickness Height Reinforcement Cutting Edge Finish Trip Mechanism Length Thickness Height Reinforcement Cutting Edge Finish Material Cover Finish Construction Valves Angle Cylinders Stroke Ram Diameter Bore Diameter Slide Box Cylinders Stroke Ram Diameter Bore Diameter Weight* Compact Width WIDE PASS™ Width BUCKET BLADE™ Width Adjus
TECHNICAL SPECIFICATIONS & CENTER OF GRAVITY INFORMATION 760TR, 860TR & 8600TR MODELS Part Moldboard Wings A-Frame Manifold Cylinders Snowplow Specs Specification 760TR 860TR 8600TR Length 92" (7'-6") 102" (8'-6") Thickness 12 ga 12 ga Height 25.5" 29.5" Reinforcement 4 Ribs @ 1/4" 4 Ribs @ 1/4" Cutting Edge 3/8" x 6" 1/2" x 6" Finish Powder Coat White Powder Coat White Trip Mechanism Springs (3) 3/8" Hooked Extension (4) 3/8" Hooked Extension Length 15.5" 17.5" Thickness 12 ga 12 ga Height 25.5" 29.
TROUBLESHOOTING – ALL MODELS library of service information to assist the qualified mechanic with repair. If you have followed all of the guidelines in the Maintenance Section of this manual and cannot resolve issues with the operation of your BLIZZARD® snowplow, contact one of our authorized outlets for repair information, or visit us online at www.blizzardplows.com. Our Web site has a complete listing of authorized outlets in your area as well as a Lit. No. B64092, Rev.
MOLDBOARD & WING PARTS – 810TR & 8611TR MODELS 8 7 20 17 15 23 19 52 44 46 43 2 4 18 24 10 54 26 53 6 34 22 29 48 47 35 37 5 3 14 36 45 20 41 49 55 12 28 11 1 32 30 27 21 9 31 38 13 27 29 40 33 16 50 51 38A 39 42 25 Item 1 2 3 4 5 6 7 8 9 10 Part B61681 B11989 B50057 B50075 B50058 B50074 B51009 B13307 B51042 B51100 B51043 B51101 B51047 B51070 B51048 B51069 B52149 B52142 Qty 810TR 8611TR 4 4 2 2 1 – – 1 1 – – 1 2 – – 2 1 – – 1 1 – – 1 1 – – 1 1 – – 1 1 – – 1 Lit
MOLDBOARD & WING PARTS – 810TR & 8611TR MODELS Item 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38A 38 39 40 41 42 43 44 45 Part B60007 56695 B60347 B60207 B61028 B61030 90576 96325 96329 96326 96330 23039 B61187 91337 B61196 B61198 B61292 B52139 63575 B61341 B61361 B61362 B61365 B61383 B61384 B61385 B61398 23039 B61400 B61416 B61418 B61360 B61419 B61361 66435 B63160 B70249 B70251 B70261 B70262 B70281 B70285 44832 59900 29593 Qty 810TR 8611TR 4 – – 4 2 – – 2 2 2 2 2 4
MOLDBOARD & WING PARTS – 810TR & 8611TR MODELS Item 46 47 48 49 50 51 52 53 54 55 Part B61049 68494 91332 B60224 96192 96190 90238 80238 91335 91337 90572 90576 29256 Qty 810TR 8611TR 1 1 4 4 4 4 4 4 2 2 2 2 7 – – 7 7 – – 7 7 – – 7 2 2 Lit. No. B64092, Rev.
MOLDBOARD & WING PARTS – 8100TR MODEL 1 16 15 44 49 51 3 35 12 37 5 2 36 4 14 10 13 19 18 33 32 48 42 38 31 39 45 29 44 43 47 7 34 46 9 22 23 24 Qty 1 1 1 1 1 8 14 2 2 2 2 2 1 52 6 28 25 27 Description Moldboard Label – Information (Warning) Label – POWER PLOW™ Center Label – TR Mount/Dismount 1/2" Moldboard Cutting Edge 1/2-13 x 1-1/2 Carriage Bolt G8 1/2-13 Flanged Locknut 3/4-10 x 1-1/2 Screw 3/4-10 Hex Locknut G8 5/8 x 11-1/2 Pin, Hydraulic Cylinder Base End – Slide Box
MOLDBOARD & WING PARTS – 8100TR MODEL Item Part 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 B51047 96326 40740 66435 63575 B61384 B70281 B61400 B70262 B70251 B70249 B70261 B70285 B61341 96190 29593 90490 B61418 B61419 B61622 B51048 B61049 68494 91332 40739 96325 B61385 90601 B55042 B55065 91337 B60347 B61167 29256 50639 90238 23039 B61416 91335 90572 Qty Description 1 1 1 2 2 6 2 2 2 2 2 2 2 4 2 4 2 2 2 2 1 1 4 4 1 1 2 2 2 1 6
MOLDBOARD & WING PARTS – 760TR & 860TR MODELS 25 8 29 2 26 5 8 6 41 40 7 17 31 42 24 8 32 9 10 18 13 16 28 4 14 44 43 15 39 30 23 37 11 22 20 36 1 3 11 15 34 19 33 22 38 43 21 27 11 12 35 11 Item 1 2 3 4 Qty Part 760TR 860TR B53021 1 – B53062-1 – 1 B53033 1 – B53075-1 – 1 B53076 2 2 B53092 1 – B53091 – 1 Description Wing – DS Wing – DS Wing – PS Wing – PS Spring Guide Moldboard Moldboard G = Grade Lit. No. B64092, Rev.
MOLDBOARD & WING PARTS – 760TR & 860TR MODELS Item Part 5 6 7 8 9 10 11 12 13 B61049 90576 91337 90238 90490 63575 B61341 B61343 B61351 B61099 90601 91335 B61400 B61561 B61570 B61563 B61564 B61572 69695 B61576 B61577 B61578 B61573 B61608 B61610 B61609 B61611 B61614 B61615 66435 B63171 96328 96323 96327 B63175 44832 B70249 B70251 B70261 B70262 B70281 B70285 29593 68494 91332 59900 90572 29256 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Qty 760TR 860TR De
BLADE ASSEMBLY – 8600TR MODEL 14 42 26 29 28 4 1 32 25 12 20 24 27 3 23 30 22 18 31 2 28 4 20 21 15 13 19 19 16 41 7 6 10 9 8 38 11 5 37 39 40 35 33 36 34 Lit. No. B64092, Rev.
BLADE ASSEMBLY – 8600TR MODEL 42408 Blade Assembly Item 1 2 3 4 5 6 7 8 9 10 11 ns 12 13 14 15 16 ns 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41‡ 42‡ ns‡ Part Qty 42409 1 49799 1 63986 8 91337 14 96190 2 66435 2 B61384 2 B70281 2 B70262 2 63575 2 B61400 2 42941 1 42942 1 42385 1 42383 1 42943 2 42397 2 42392 1 42393 1 42725 2 29593 4 29256 2 44832 1 42396 2 B63175 1 B61614 2 42386 1 59900 1 90576 14 5572 6 66439 2 91333 2 42395 4 B70251 2 B70261 2 B61341 4 B70285 2 96192 2 90
BLADE COMPONENTS – 8600TR MODEL 9 3 7* 11 10 13 14 15 8 5 12 6 4 2 1 * Pins used to lock wings in straight position Lit. No. B64092, Rev.
BLADE COMPONENTS – 8600TR MODEL Blade Components Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part B61615 B61343 90576 42389 B61563 90601 42738 91962 91337 90490 50655 23039 B61049 68494 91332 Lit. No. B64092, Rev. 06 Qty 2 2 4 2 2 2 2 2 4 4 4 4 2 4 4 Description 3/4-10 Hex Jam Nut 3/4-10 Hex Nut 5/8 Hardened Flat Washer Cable Assembly w/Hardware (incl. items 1, 2, 5 and 6) Ø .625 x 2.
A-FRAME & PIVOT BEAM PARTS – 810TR & 8100TR MODELS 32 30 9 13 2 36 11 20 9 2 17 18 16 18 7 3 2 14 25 14 12 1 18 18 19 28 23 15 8 31 34 18 33 22 23 4 10 19 6 28 35 23 21 9 26 10 5 24 29 27 Lit. No. B64092, Rev.
A-FRAME & PIVOT BEAM PARTS – 810TR & 8100TR MODELS Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Part B52151 95739 B50069 B50071 40571 B60029 B60545 B61008 29233 B61034 50605 B61203 90055 B61217 B61275 B61307 66439 90601 B61384 44413 B61638 B61644 66435 B61720 B70265 B70272 B70273 B70277 B70278 B70287 B70291 B70293 B70294 B70295 B60223 29328 Lit. No. B64092, Rev.
A-FRAME & PIVOT BEAM PARTS – 8611TR MODEL 9 1 21 7 17 20 12 10 2 17 6 19 27 8 4 7 34 24 16 3 28 31 29 25 7 Tractor-Specific Hook Mounts 26 23 22 30 11 7 35 32 18 15 14 7 5 33 13 7 8 33 Lit. No. B64092, Rev.
A-FRAME & PIVOT BEAM PARTS – 8611TR MODEL Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Qty Part 8611TR 95739 4 B41077 1 40571 2 B60324 2 B60522 1 B61008 1 29233 24 B61034 11 50605 1 B61203 1 90055 4 B61217 2 B61275 4 B61307 1 66439 1 80239 4 90601 6 44413 2 B61644 3 B61717 2 90118 8 B70089 1 B70102 2 B70103 2 B70104 4 B70105 4 B70106 1 B70121 4 B70122 4 B70143 1 B70240 8 B70247 1 B70295 2 B60224 2 29328 1 Lit. No. B64092, Rev.
A-FRAME & PIVOT BEAM PARTS – 760TR, 860TR & 8600TR MODELS 3 13 10 31 15 2 1 29 18 12 18 9 16 37 1 38 24 11 2 7 17 27 34 22 16 4 14 32 30 32 33 22 36 26 16 20 16 2 17 4 35 11 8 27 22 5 6 16 19 25 21 23 28 Tractor-Specific Hook Mounts Lit. No. B64092, Rev.
A-FRAME & PIVOT BEAM PARTS – 760TR, 860TR & 8600TR MODELS Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Part B16536 42410 95739 B41056 B41066 B50071 40571 B60065 B60029 B60534 B60539 B61008 29233 B61039 B61203 90055 B61275 B61331 50605 90601 B61384 B61616 B61638 B61644 91331 66435 B61720 94498 B70272 B70273 B70277 B70278 B70287 B70291 B70293 B70294 B70295 B70324 B70320 B60224 B60473 66439 91333 760TR 2 Qty 860TR 2 4 1 – 2 2 2 – 1 2 1 5 4 1
MANIFOLD PARTS – 810TR, 8100TR & 8611TR MODELS 3 12 2 3 7 4 4 5 6 5 10 13 14 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Part B60545 B60522 B60168 B60278 B60226 B60279 B60227 B60528 B60529 B62263 B60530 B60007 B60340 56695 B60007 B60052 B60531 B60473 Qty 810TR 8611TR 1 – – 1 1 1 2 – – 2 2 – – 2 2 2 1 1 3 3 2 2 2 2 1 1 6 – – 6 6 6 1 1 2 2 Lit. No. B64092, Rev.
MANIFOLD PARTS – 760TR, 860TR & 8600TR MODELS 2 1 3 Item 1 2 3 Part B60534 B60168 B60403 Lit. No. B64092, Rev.
ACCESSORIES & KITS – ALL MODELS 1. Rugged and durable, the 3/8" thick, 2-ply Rubber Snow Deflector keeps snow off your windshield and in its place—on the ground! The one-piece design allows for wing clearance and provides optimum snow deflection. The deflector is shipped with a vinyl label and complete mounting hardware. 3.
ACCESSORIES & KITS – ALL MODELS Item 1 Quantity 810TR 8100TR 8611TR 760TR 1 1 – – – – 1 – – – – – 1 1 – – – – 1 – 1 1 – – – – 1 – 1 1 1 1 1 1 1 1 – – – – – – – 1 ns ns Part B61241 B52087 42384 B61288 B51114 B61536 B61539 B61219 B63073 42382 B21034 ns ns ns ns ns ns ns B61277‡ B61665‡ B61479 B61724‡ B61723‡ 42416‡ B60535** 1 – – – – – 1 1 1 – – – – 1 – – 1 – – – – – – – 1 – – – – – – – 1 – – – – – – – 1 – Hardware Kit, Snowplow Assembly Parts Hardware Kit, Snowplow Assembly Parts Hardware Kit, S
Blizzard PO Box 245038 Milwaukee, WI 53224-9538 www.blizzardplows.com A DIVISION OF DOUGLAS DYNAMICS, L.L.C. This product conforms to EU Machinery Directive 2006/42/EC. Copyright © 2012 Douglas Dynamics, L.L.C. All rights reserved. This material may not be reproduced or copied, in whole or in part, in any printed, mechanical, electronic, film or other distribution and storage media, without the written consent of Blizzard.
