Dishwasher Installation Manual DW 51600 SS DWT 52600 SSIH DW 51600 FBI DWT 52600 BIH DWT 51600 SS DWT 52800 WIH DWT 51600 FBI DWT 52800 SSIH DWT 81800 FBI DWT 81900 FBI DWT 81800 SS DWT 51600 W DWT 81800 SSIH DWT 81900 SS DWT 81800 SSWS DWT 52600 WIH
Dishwasher Installation Manual DW 51600 SS DWT 52600 SSIH DW 51600 FBI DWT 52600 BIH DWT 51600 SS DWT 52800 WIH DWT 51600 FBI DWT 52800 SSIH DWT 81800 FBI DWT 81900 FBI DWT 81800 SS DWT 51600 W DWT 81800 SSIH DWT 81900 SS DWT 81800 SSWS DWT 52600 WIH
To prevent accidents, which could cause serious injury or death, as well as machine damage read these instructions before installation and / or use. INTRODUCTION 1 1. IMPORTANT SAFETY INSTRUCTIONS 1 2. TOOLS WHICH MAY BE NEEDED 3 3. MATERIALS WHICH MAY BE NEEDED 3 4. MATERIALS SUPPLIED 4 5. DISHWASHER SPECIFICATIONS 5 6. ENCLOSURE PREPARATION 6 1.1 INSPECT THE DISHWASHER 4.1 PARTS SUPPLIED 4.2 MANUAL BAG 4.3 DISHWASHER PARTS BAG 1 4.4 DISHWASHER PARTS BAG 2 4.
INTRODUCTION WARNING Please read this installation manual and particularly the safety instructions completely and carefully. They will save you time and effort and help to ensure optimum dishwasher performance. When installing the dishwasher, follow basic precautions, including the following: • The dishwasher could only be converted from cord-connected to permanently connected by an authorized service representative.
• • • • 1.1 INSPECT THE DISHWASHER designed for an electrical supply of 120 V (volts), 60 Hz (hertz), AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breakers rated for 15 amperes. Electrical supply conductors shall be a minimum of # 16 AWG copper wire rated at 75 °C (167 °F) or higher. These requirements must be met to prevent injury and machine damage. Consult a qualified electrician if in doubt.
2. TOOLS WHICH MAY BE NEEDED 3. MATERIALS WHICH MAY BE NEEDED (Additional materials may be required to comply with local codes) Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. Elbow with 3/4” N.P.T. female thread for dishwasher side, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other side. Dishwasher connection is 3/4" male. UL listed conduit connector or strain relief.
4. MATERIALS SUPPLIED 4.1 PARTS SUPPLIED Parts for your dishwasher will come in several plastic bags. Check your parts bags shown to make sure you have all the parts as listed to the left. 4.2 MANUAL BAG The dishwasher comes with a manual bag containing: • User manual, • Installation manual 4.3 DISHWASHER PARTS BAG 1 This dishwasher bag comes with the following parts: a. Side Trim Strips (Left) b. Side Trim Strips (Right) d. Screws Ø 1/8” x 5/8” (Ø 3.5 mm x 14 mm) e. Mounting Bracket Left f.
5.
5.1 TECHNICAL FEATURES Permissible water pressure Electrical connection Total power Heater power 4.35 - 145 psi (0.3 - 10 bars) 120 V (volts), 12 A (amps), 60Hz (hertz) 1400 W (watts) 1100 W (watts) NOTICE : Because we continually strive to improve our products, we may change our specifications and design without prior notice. This device corresponds to the following directives: UL 749 Household Dishwasher directive.
6. ENCLOSURE PREPARATION 6.1 ELECTRICAL PREPARATION WARNING The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amperes. 6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS WARNING Dishwasher must be secured to adjacent cabinetry using the mounting brackets provided. Failure to do this may cause damage to property or bodily injury.
d) ? 8 USA
j (Standart tub models) + 50 max 50 (+50mm) Place the two mounting brackets into the top corners of the dishwasher. Fix the mounting brackets (A) to the top corners of the dishwasher, with the screws supplied. Bend sides of mounting brackets (B) in order to fix from sides (if necessary).
6.3 ADJUSTING HEIGHT If the height of the enclosure is 337/8” to 357/8” (861 mm - 911mm) adjust supports as shown in the figure. Supplied (4) Adjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height. Adjust the rear foot level with a screwdriver to balance and raise the dishwasher to the enclosure height. NOTICE : • Make sure the dishwasher is plumb and notice dishwasher can be placed with a small clearance under the counter top.
6.5 PREPARING THE WATER CONNECTION (A) Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections must be made before the water line is connected to the dishwasher’s water inlet valve. Water can also be supplied to the dishwasher by using a flexible braided hose line. Check with your plumbing supply sources for the proper hose and elbow and necessary fittings for the water supply line. This material is not supplied, and must be purchased separately.
NOTICE : • Either one of the above methods must be used or the dishwasher will not operate properly. • A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink has one, it is recommended that the hose be disconnected and the hole plugged. • The total length of the drain hose is 763/4” (1950mm). If a hose extension is required, a drainage hose of equal quality must be used. • The maximum length must not exceed 157 ½” (4000mm).
6.7 STEAM PROTECTION FOIL Steam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it is required to use a steam protection foil to prevent any steam from collecting on the underside of the counter top. 6.6.2 FITTING THE PROTECTION FOIL Before applying the steam protection foil to the underside of the countertop, clean the area with a damp cloth (as shown in Figure A). Once the area dries, apply the steam protection foil.
7. PLACEMENT OF DISHWASHER INTO THE OPENING Now place the dishwasher into the opening and get ready to connect all hoses and electrical connections. CAUTION Make sure all hoses are pulled through the side opening of the cabinet, no hoses are kinked and all slack is taken out as shown in the above figure. 7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS 7.1.1 DRAIN HOSE CONNECTION Connect the drain hose to the drain plumbing. 1.
7.1.2 WATER SUPPLY CONNECTION Water supply may be connected to the dishwasher in one of two ways: • With metal braided hose. • With copper tubing. CAUTION • Hot water supply line: Use minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. • Temperatures required for soldering and sweating will damage the dishwasher’s water inlet valve so if any such operation is needed, keep the heat source min. 77/8” (200mm) away from the dishwasher’s water inlet valve.
7.2 READJUSTING FOOT LEVELS Now that the dishwasher is in the cabinet you must readjust the feet to bring the dishwasher up to the required height and attach it underneath the countertop. 1. Readjust the front foot levels with adjusting wrench to balance the dishwasher and raise it up under the countertop, make sure the unit is level. 2. Readjust the rear foot levels with a screwdriver to balance the dishwasher and raise it to the required height using the brackets supplied. 3.
TALL TUB MODELS ONLY Open the fixing part on the Toe Kick(p). (A) Place it on the slots, which are on the brackets fixed before, and adjust the height (max. 40 mm). (B) Close the fixing part on the Toe Kick.
7.
TALL TUB MODELS y 19 USA
7.5 PREPARING THE TIMBER DOOR X o) X =? s) = = = = Mid. Point Mid.
7.
7.9 INSTALLING THE TIMBER DOOR 4 1 3 2 7.
7.11 FIXING THE TIMBER DOOR (y) Ø 4 x 36mm 12 34 5 1 23 45 7.12 ADJUSTING THE KICK PLATE • Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A). • If the door hits the toe kick cut the necessary section out of the toe kick (B). • Apply silicon or sealant to the cut edge of the kitchen cabinet toe kick or paint so it does not absorb moisture.
4 ~ 1500 ~ 1800 ~ 2000 min 300 min 500 max 1000 1 1 2 2 1 1 24 2 USA min 300 2 min 120 max 1000 3 min 500 max 1000 7.
8. INSTALLER CHECKLIST Your installer must have completed and checked the following: • The dishwasher is square and level. • The dishwasher is fastened securely to the cabinetry. • The dishwasher door opens and closes freely. The dishwasher door must close without hitting any cabinetry or counter top. • The inlet water supply is turned on and checked for leaks. • The drain hose has been connected and checked for leaks. There must be no kinks or obstructions in the drain hose.
www.blomberginternational.com info@blomberginternational.
