Dishwasher Installation Manual FOR MODELS DWT 14210 NBL00 DWT 14220 NBL00 DWT 14240 NBL00 DWT 15210 NBL00 DWT 15220 NBL00 DWT 15240 NBL00 DWT 15211 NBL00 DWT 15221 NBL00 DWT 15241 NBL00 DWT 34210 NBL00 DWT 34220 NBL00 DWT 34240 NBL00 DWT 34200 NBL00 DWT 35210 NBL00 DWT 35220 NBL00 DWT 35240 NBL00 DWT 35200 NBL00 DWT 36210 NBL00 DWT 36220 NBL00 DWT 36240 NBL00 DWT 36211 NBL00 DWT 36221 NBL00 DWT 36241 NBL00 DWT 36200 NBL00 DWT 36201 NBL00 DWT 37200 NBL00 DWT 37210 NBL00 DWT 37220 NBL00 DWT 37240 NBL00 DWT
Installation Manual For Dishwasher Models DWT 15211 NBL00 DWT 15221 NBL00 DWT 15241 NBL00 DWT 14210 NBL00 DWT 14220 NBL00 DWT 14240 NBL00 DWT 15210 NBL00 DWT 15220 NBL00 DWT 15240 NBL00 DWT 14440 ULTRA DWT 14410 ULTRA DWT 14420 ULTRA DWT 34210 NBL00 DWT 34220 NBL00 DWT 34240 NBL00 DWT 34200 NBL00 DWT 35210 NBL00 DWT 35220 NBL00 DWT 35240 NBL00 DWT 35200 NBL00 DWT 36210 NBL00 DWT 36220 NBL00 DWT 36240 NBL00 DWT 36211 NBL00 DWT 36221 NBL00 DWT 36241 NBL00 DWT 36200 NBL00 DWT 36201 NBL00 DWT 37200 NBL00
To prevent accidents, which could cause serious injury or death, as well as machine damage read these instructions before installation and / or use. Contents 1. IMPORTANT SAFETY INSTRUCTIONS 1 1.1 INSPECT THE DISHWASHER 1.2 HOW TO CONTACT US 2 2 2. TOOLS WHICH MAY BE NEEDED 3 3. MATERIALS WHICH MAY BE NEEDED 3 4. MATERIALS SUPPLIED 4 4.1 PARTS SUPPLIED 4.2 MANUAL BAG 4.3 DISHWASHER PARTS BAG 1 4.4 DISHWASHER PARTS BAG 2 4.5 PARTS ATTACHED TO THE REAR OF THE DISHWASHER 4 4 4 4 4 5.
INTRODUCTION WARNING Please read this installation manual and particularly the safety instructions completely and carefully. They will save you time and effort and help to ensure optimum dishwasher performance. When installing the dishwasher, follow basic precautions, including the following: The dishwasher installation must be performed in accordance with this installation manual.
be met to prevent injury and machine damage. Consult a qualified electrician if in doubt. Do not use any extension cord or portable outlet device to connect the dishwasher to a power supply. Ensure that any plastic wrappings, bags, small pieces etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Remove the door to the washing compartment when removing an old dishwasher from service or discarding it.
2. TOOLS WHICH MAY BE NEEDED 3. MATERIALS WHICH MAY BE NEEDED (Additional materials may be required to comply with local codes) Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. Electrical Supply Cable - Minimum #14AWG, 2 conductors, 1 ground, insulated copper conductors. 90° elbow with 3/8” N.P.T. male threads on one leg, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other leg.
4. MATERIALS SUPPLIED 4.1 PARTS SUPPLIED a. x1 b. x1 Parts for your dishwasher will come in several plastic bags. Check your parts bags shown to make sure you have all the parts as listed to the left. c. x1 4.2 MANUAL BAG d. x6 e. x1 The dishwasher comes with a manual bag containing: User manual, Installation manual and Quick reference guide. f. x1 4.3 DISHWASHER PARTS BAG 1 g. x1 h. x1 j. x1 k. x1 l. x1 m. x3 n. x4 o. x1 p.
34 - 361/4 (864mm - 920mm) 5. DISHWASHER SPECIFICATIONS 24m) 0m 1 (6 33 7/8- 35 7/8 (861mm - 911mm) 239 (598 /16 mm ) 2 (61 4 0m m) axax) mm 4 2 m 0m 61 ( 5.1 TECHNICAL FEATURES Load capacity 12 place settings Permissible water pressure 4.35 - 145 psi (0.
6. ENCLOSURE PREPARATION Notice : For proper dishwasher operation and appearance ensure that the enclosure has the minimum dimensions shown in the figure above. 6.1 ELECTRICAL PREPARATION WARNING To avoid electrical shock and/or a fire hazard, make sure electrical work is properly installed. Only qualified electricians should perform electrical work. Before installation disconnect the power supply to the work area by unplugging the unit, “tripping” the circuit breaker or removing the fuse.
6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS WARNING Dishwasher must be secured to adjacent cabinetry using the mounting brackets provided. Failure to do this may cause damage to property or bodily injury. A B Place the two mounting brackets into the top corners of the dishwasher. Fix the mounting brackets (A) to the top corners of the dishwasher, with the screws supplied. Bend sides of mounting brackets (B) in order to fix from sides (if necessary). B A 6.
Adjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height. Adjust the rear foot level with a screwdriver to balance and raise the dishwasher to the enclosure height. Notice : T20 Make sure the dishwasher is plumb and notice dishwasher can be placed with a small clearance under the counter top. Turning the screwdriver in the direction of the black arrows will bring the dishwasher back feet up.
6.5 PREPARING THE WATER CONNECTION (A) Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections must be made before the water line is connected to the dishwasher’s water inlet valve. Water can also be supplied to the dishwasher by using a flexible braided hose line. Check with your plumbing supply sources for the proper hose and 90° elbow and necessary fittings for the water supply line. This material is not supplied, and must be purchased separately.
6.6 DRAIN PREPARATION The dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figure A, B, C). Notice : Either one of the above methods must be used or the dishwasher will not operate properly. A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink has one, it is recommended that the hose be disconnected and the hole plugged. The total length of the drain hose is 763/4” (1950mm).
6.7 STEAM PROTECTION FOIL Steam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it is required to use a steam protection foil to prevent any steam from collecting on the underside of the counter top. 6.6.2 FITTING THE PROTECTION FOIL Before applying the steam protection foil to the underside of the countertop, clean the area with a damp cloth (as shown in Figure A). Once the area dries, apply the steam protection foil.
7. PLACEMENT OF DISHWASHER INTO THE OPENING Now place the dishwasher into the opening and get ready to connect all hoses and electrical connections. CAUTION Make sure all hoses and electrical wire are pulled through the side opening of the cabinet, no hoses are kinked and all slack is taken out as shown in the above figure. 7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS 7.1.1 DRAIN HOSE CONNECTION Connect the drain hose to the drain plumbing. 1.
7.1.
After installing one clip for each side push the dishwasher into the cabinet (Figure E). E F F G G 14 USA Note that while pushing the dishwasher into the cabinet, electrical cable and water supply hose must move in the channels to the front (Figure F). Fix the second clip for both sides (Figure G).
7.1.3 WATER SUPPLY CONNECTION Water supply may be connected to the dishwasher in one of two ways: With metal braided hose. With copper tubing. CAUTION Hot water supply line: Use minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. Temperatures required for soldering and sweating will damage the dishwasher’s water inlet valve so if any such operation is needed, keep the heat source min. 77/8” (200mm) away from the dishwasher’s water inlet valve.
Install a strain relief (not supplied) into the opening on the kick plate. (Figure A) A Pass the electrical supply cable through the strain relief; make sure the strain relief clamps the insulated outer casing of your electrical supply cord and not the wires themselves. Leave 215/16” “ to 315/16” “ (75mm / 100mm) of insulated wire extending through the strain relief (Figure B). Tighten the strain relief screws. (Make sure you can not pull the electrical cord out) of the strain relief.
7.2 READJUSTING FOOT LEVELS Now that the dishwasher is in the cabinet you must readjust the feet to bring the dishwasher up to the required height and attach it underneath the countertop. Ø 1/8" (3,5mm) Ø 1/8" (3,5mm) 1. Readjust the front foot levels with adjusting wrench to balance the dishwasher and raise it up under the countertop, make sure the unit is level. 2. Readjust the rear foot levels with a screwdriver to balance the dishwasher and raise it to the required height using the brackets supplied.
If the enclosure height is below 331/16” (840mm) use only “o” labelled toe kick (toe kick without slots). Installation should be done following the steps illustrated in the Figures A, B and C respectively. 1. Bend tabs on toe kick (o) inwards (A). 2. Secure toe kick to brackets with screws (t) as shown in the supply bags (B). 3. Attach caps (s) as shown in the supply bags (C). o A B t s C If the enclosure height is above 331/16” (840mm) use “o” and “p” labelled toe kicks together.
2. Remove the plastic mounting brackets from the dishwasher (Figure B). B 3. Lay the schematic over the door from the bottom up and mark holes on the wooden door as shown in the drawing (Figure C). 6 11 / 1 m) 8 ,2m 1 (22 221,2mm Mid. Point C D 4. Place the plastic mounting brackets over the marked holes and the side tabs must be flush with the edge of the wooden door (Figure D).
Ø 1/8" (3,5mm) 5. Attach the two mounting brackets to the wooden door with 4 screws (Ø 1/8” x 5/8” (Ø 3.5mm x 14mm) (Figure A). x4 v A 6. Mount the wooden door onto the dishwasher with the plastic mounting brackets which you have attached (Figure B). B 7. Open the door and remove the two caps and two screws inside the door at position 1 and 4 (Figure C).
8. Using the four screws Ø 3/16” x 111/16” (Ø 4mm x 43mm) provided, attach the wooden door to the dishwasher at position 1 and 4 (Figure A). Ø 3/16" (4mm) x4 y A 9. Check the position of the wooden door and make sure it is aligned properly (Figure B). B 10. Tighten the screws in position 1 and 4 completely after the final alignment (Figure C).
B 11. Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A). 11.1. If the door hits the toe kick cut the necessary section out of the toe kick (B). 11.2. Apply silicon or sealant to the cut edge of the kitchen cabinet toe kick or paint so it does not absorb moisture.
Notice : If you have a European kitchen or want to install a wooden toe kick to match your kitchen, please refer to one of the two drawings given below. Follow the same instructions on the brackets as for the removable toe kick. Installation should be done following the steps illustrated in the figures A, B, C, D respectively.
Notice : 8. INSTALLER CHECKLIST Your installer must have completed and checked the following: The dishwasher is square and level. The dishwasher is fastened securely to the cabinetry. The dishwasher door opens and closes freely. The dishwasher door must close without hitting any cabinetry or counter top. The inlet water supply is turned on and checked for leaks. The drain hose has been connected and checked for leaks. There must be no kinks or obstructions in the drain hose.
17 1844 01 00 AC-USA