Please read this manual first. Dear Customer, We would like you to obtain best performance with your product that has been manufactured in modem facilities and passed through strict quality control procedures. Therefore, we advise you to read through this User Manual carefully before using your product and keep it for future reference. If you hand over the product to someone wise, deliver the User Manual as well, The User Manual will help you use the product in a fast and safe way.
Table of Contents General C Overview Technical Data. Injector table... E Safety misconstructions. B Basic safety oo Safety when working with gas Intended use Safety for children B Installation Before installation Installation and connection Gas Disposing of packaging material Old BRAWN O Future transportation E Preparation... Tips for saving energy. initial operation First cleaning of the appliance .
fl General information Overview Pan support 5 Base cover 2 Spark plug & Rapid boomer 3 Control pane! 7 Burners' plate 4 Auxiliary boomer Auxiliary burner Front 2 Rapid boomer Rear 4]EN
Technical Data Voltage/frequency 220-240V ~ 50 Hz Cable type / cross section 0,75 mim Cable length max. 2 m (Gas device category 1l 230 Gas acupressure NG 20/20 mar Total gas consumption 3.
E Safety instructions Basic safety instructions . The manufacturer reserves its right to make changes in the technical specifications in order to improve the appliance quality without any prior notice. Figures included in this manual are for schematic purpose only and may not match exactly with your appliance. Values stated on the markings of the appliance or in other printed documents supplied with the appliance are obtained under laboratory conditions as per relevant standards.
gas pressure} and the adjustment of the appliance are compatible.” “This appliance is not connected 1o a combustion products evacuation device. It shall be installed and connected in accordance with current installation regulations. Particular attention shall be given to the relevant requirements regarding ventilation;" See Before installation, page 8 “The use of gas cooking appliance results in the production of heat and moisture in the room in which it is installed.
appliance is in use and until the * The packaging materials will be appliance has cooled, children dangerous for children. Keep the should be kept away. packaging materials away from Do not store any items above the children. Please dispose of all appliance that children may reach. parts of the packaging according o environmental standards.
E Installation Before installation The hob is designed for installation in a commercial worktop. A safety distance must be left between the appliance and the kitchen walls and furniture, See figure {values in mm). + Remove packaging materials and transport locks. min, Room ventilation The air for combustion is taken from the room air and the exhaust gases are emitted directly into the room. Good room ventilation Is essential for safe operation of your appliance.
Room size Ventilation opening smaller than 5 m° | min. 100 ent 5m toil’ min. 50 cm greater than 10_m" | not required in the cellar or min. 65 o basement Installation and connection s For installation the appliance must be connected in accordance with all local gas and/or electrical regulations. Connection to the mains supply [} This appliance must be earthed! Cur company shall not be held responsible for any damage caused by using the appliance without an earthed socket.
of this pipe must be closed with a plug. Service Representative will remove the plug during connection and connect your appliance by means of a straight connection device {coupling). Make sure that the natural gas valve is readily accessible. If you need to use your appliance later with a different type of gas, you must consult the authorized Service for the related conversion procedure. Leakage control at the connection point Make sure that all knobs on the appliance are turned off.
Gas conversion A Risk of explosion! Before starting any work on the gas installation, please shut off the gas supply. in order to change your appliance's gas type, change all injectors and make flame adjustment for all valves at reduced flow rate position. Exchange injector for the burners 1. Take off burner cap and burner body. 2. Unscrew injectors. 3. Fit new injectors. 4, Check all connections for secure fitting and tightness.
1 Flow rate adjustment screw If the gas type of the unit is changed, then the rating plate that shows the gas type of the unit must also be changed. Disposal Disposing of packaging material Packaging materials are dangerous to children, Keep packaging materials in a safe place out of reach of children. Packaging materials of the product are manufactured from recyclable materials.
Preparation Tips for saving energy The following tips will help you to use your appliance in an ecological way and to save energy: . Use pots/pans with lids for cooking. Without a lid, the energy consumption may be up to four times higher. Choose the burner/plate which is suitable to the saucepan base. Always choose the correct size of saucepans for your meals, For larger burners/plates more energy is needed.
5 How to use the hob General information on cooking A, Risk of fire by overheated oil! When you heat oil, do not leave it unattended. Never try to extinguish the fire with water! When il has caught fire, immediately cover the pot or pan with a lid. Switch off the hob if safe to do so and phone the fire service. + Ensure handles of pans cannot accidentally be caught or knocked and do not get hot by adjacent heating zones. Avoid pans that are unstable and easily tipped.
Flame failure device {model . dependent} in case of any flame failures for any reasons in the top numbers, the flame failure device immediately cuts off the gas flow. 1. Flame failure A device + Turn the knob clockwise direction by pressing and wait for its ignition. 16| EN Keep the knob at pressed position for 3-5 seconds after you see the flame around the burner. Repeat the sequence of operations if the flame does not ignite.
E Maintenance and care General information A B Risk of electric shock! Switch off the electricity before cleaning appliance to avoid an electric shock. A Hot surfaces may cause burns! Allow the appliance to cool down before you clean it. [f] The surface may get damaged by some detergents or cleaning materials. Do not use aggressive detergents, cleaning powder/cream or any sharp objects.
Troubleshooting A\ Risk of explosion or poisoning by Normal operating conditions unprofessional repair. * Smoke and smell may emit for a Repairs on the appliance must be couple of hours during the first carted out by an approved operation. service confrere. * When the metal pairs are heated, they may expand and cause noise, Before you call the service, please check the following points.
