595 OWNERS MANUAL for HEATED DISPENSER MODEL: HD8799 2½-Gallon HD8802 5-Gallon Includes: Installation Operation Use & Care Servicing Instructions Model HD8799 Heated Dispenser IMPORTANT: DO NOT DISCARD THIS MANUAL This manual is considered to be part of the appliance and is to be given to the OWNER or MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of this appliance. Additional manuals are available from your WELLS DEALER.
LIMITED WARRANTY STATEMENT Unless otherwise specified, all commercial cooking equipment manufactured by WELLS MFG. CO. is warranted against defects in materials and workmanship for a period of one year from the date of original installation or 18 months from the date of shipment from our factory, whichever comes first, and is for the benefit of the original purchaser only.
TABLE OF CONTENTS WARRANTY SPECIFICATIONS FEATURES & OPERATING CONTROLS PRECAUTIONS & GENERAL INFORMATION AGENCY LISTING INFORMATION INSTALLATION OPERATION CLEANING INSTRUCTIONS TROUBLESHOOTING SUGGESTIONS SERVICING INSTRUCTIONS EXPLODED VIEW & PARTS LIST FAUCET REPAIR WIRING DIAGRAM PARTS & SERVICE xi 1 2 3 3 4 5 6 7 8 10 10 11 Thank You for purchasing this Wells Manufacturing Co. appliance.
FEATURES & OPERATING CONTROLS Fig.
PRECAUTIONS AND GENERAL INFORMATION WARNING: Electric Shock Hazard All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock. WARNING Electric Shock Hazard Warmer must be properly grounded to prevent possible shock hazard. Electrical shock will cause death or serious Injury. This appliance is intended for commercial use only.
INSTALLATION READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION CAUTION: Equipment Electrical Damage DO NOT plug in or energize this appliance until all Installation Instructions are read and followed. Damage to the Brewer will occur if these instructions are not followed. CAUTION: Unstable Equipment Hazard It is very important for safety and for proper operation that the warmer is level and stable when standing in its final operating position.
OPERATION PREPARATION Prior to first use, thoroughly clean warmer (see page 6). Be sure faucet handle is "up" and that drip tray is in place under faucet. USE Pour product into warming tank. Using pre-heated product will reduce heat-up time. Model HD8799 utilizes a fixed thermostat to hold product at 140ºF (60ºC). Model HD8802 thermostat may be adjusted to hold product at 170ºF (77ºC) maximum. Reinstall tank cover. Plug dispenser into an appropriate electrical receptacle. Turn power switch to ON.
CLEANING INSTRUCTIONS CAUTION: Electric Shock Hazard Do not submerge or immerse dispenser in water. CAUTION: Burn Hazard This procedure requires the use of very hot water. Wear protective gloves while cleaning the warmer. Very hot water can cause burns. IMPORTANT: DO NOT use steel wool, sharp objects, or caustic, abrasive or chlorinated cleansers to clean the dispenser. PROCEDURE: Clean Heated Dispenser PRECAUTIONS: Disconnect dispenser from electric power. Drain product and allow dispenser to cool.
TROUBLESHOOTING SUGGESTIONS SYMPTOM Appliance will not heat POSSIBLE CAUSE SUGGESTED REMEDY Not plugged in or circuit breaker off or tripped Restore electric power to warmer Power switch not ON Turn power switch to ON Internal wiring damage Inspect wiring for burnt wires and proper connections .
EXPLODED VIEW & PARTS LIST MODEL HD8799 2½-GALLON DISPENSER ITEM PART # 1 85865 DESCRIPTION FAUCET ASSEMBLY QTY ITEM PART # 1 DESCRIPTION QTY 6 85853 HEATING ELEMENT 120V 200W 1 1.1* BODY FAUCET 7 85863 THERMOSTAT 140ºF 120V 1 1.2* 8700-25L SEAT CUP 8 50169 SWITCH 250V DPST 1 1.3* ASSEMBLY, HANDLE & PLUNGER 9 65174 GUARD, SWITCH 1 NUT RETAINING WINGED 10 80017 POWER CORD, 120V NEMA5-15P, 6' 1 SHANK, FAUCET W/O SIGHT GLASS 11 68689 STRAIN RELIEF 120V STRAIGHT 1 1.
EXPLODED VIEW & PARTS LIST MODEL HD8802 5-GALLON DISPENSER ITEM PART # 1 85865 1.1* 1.2* 8700-25L 1.3* 1.4* 8600-27 1.
SERVICING INSTRUCTIONS CAUTION Electric Shock Hazard Opening the bottom panel will expose uninsulated electrical components. Disconnect dispenser from electrical power before removing bottom panel. ACCESS - BOTTOM PANEL All internal components are accessible by removing the bottom panel. Remove four screws around the bottom of the warmer tank to free bottom panel from tank assembly. FAUCET The faucet may be removed from the shank by turning the winged collar clockwise.
PARTS & SERVICE DESCRIPTION PART NO. DRIP TRAY ASSEMBLY (pk 6) 8855-1 IMPORTANT: Use only factory authorized service parts and replacement filters. For factory authorized service, or to order factory authorized replacement parts, contact your Wells authorized service agency, or call: Wells Manufacturing Co. 2 Erik Circle P. O. Box 280 Verdi, NV 89439 phone: (775) 689-5700 fax: (888) 492-2783 (Service Parts Dept.
