SATELLITE DOCKING STATION BLOOMFIELD MODEL: SDS-1 TABLE OF CONTENTS Introduction General Layout Data Sheet Features Warranty Safety Installation Instruction Leveling the Unit Electrician's Installation Instructions 73342 Rev (-) Page Page Page Page Page Page Page Page 1 2 3 4 5 6 6 6 Initial Installation Instructions Quality Timer Adjustment Instructions Exploded View Parts Identification Ordering/Service Procedure Troubleshooting Schematic — Wiring Diagram Page Page Page Page Page Page Page Page 6
INTRODUCTION BLOOMFIELD MODEL: SDS-l HI-QUALITY SATELLITE DOCKING STATION Thank you for purchasing a Bloomfield Satellite Docking Station. You will achieve maximum performance from this unit if you familiarize yourself with its many outstanding features. Please take a few minutes to read through the owner’s manual. Proper installation is very important if maximum performance and satisfaction are to be achieved. If you have any difficulties, consult your nearest, Bloomfield Authorized Distributor.
GENERAL LAYOUT DATA BLOOMFIELD SATELLITE DOCKING STATION MODEL: SDS-1 ELECTRICAL SPECIFICATIONS Model WATTS VOLTS AMPS 503-1 45 (with one Satellite) 120 .
FEATURES MODELS SDS-l SATELLITE DOCKING STATION manufactured by BloomfIeld Industries Inc., Is designed to hold coffee at a correct temperature for serving. 0 Operates on 120 Volt, .4 Amp, 45 Watt service. 0 Safety feature including absence of any hot surfaces. 6 Automatic Start when Satellitte is in place, 0 Ideal for self service applications. 0 Auto safety electrical shut-off when Satellite is removed. 0 Adjustable non-skid rubber feet on brewer for easy leveling.
WARRANTY POLICY All electrical products manufactured by Wells/Bloomfleld are warranted against defects in material and workmanship by our authorized service agents with: o One (1) year replacement part warranty 0 One (1) year. on labor 0 All genuine. Wells/Bloomfield replacement parts are warranted for ninety (90) days from date of purchase on non-warranty equipment. This parts warranty is limited only to replacements of the defective part.
THIS WARRANTY IS THE COMPLETE AND ONLY WARRANTY, EXPRESS OR IMPLIED IN LAW OR FACT, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS _ FOR ANY PARTICULAR PURPOSE, AND/OR FOR DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH WELLS/BLOOMFIELD PRODUCTS.
INSTALLATION INSTRUCTION READ THIS COMPLETELY BEFORE STARTING THE INSTALLATION `- ! CAUTION: DO NOT plug in or energize this unlt until lnstallation Instructions are read and followed. Damage to the Unit will occur If the Instructions are not followed. To enable the installer to make a quality installation and hold delay time to a minimum, the following suggestions and tests should be done before the actual unit installation is begun.
QUALITY TIMER ADJUSTMENT INSTRUCTIONS Flashing light timer is preset from the factory for 30 minutes. ! ! To increase the holding time: ELECTRICAL SHOCK HAZARD: Disconnect power supply to Unit before removal of any panel or replacement of any component. Electrical shock will cause death or serious injury. CAUTION: All adjustments should be made by a authorized Bloomfield Service Technician I Timer Adjustment 1. Unplug unit from the electrical outlet. 2. Remove Rear panel. (See item 5 on page 8) 3.
ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 15 16 17 SERVICE 8718-31 83081 83046 83077 83098 83107 83102 83105 35-210 6407-15 DESCRIPTION TOP HOUSING WLD ASSY PILOT LIGHT GREEN 120V SHIELD FUNNEL PLATE BTM TOP HOUSING PANEL BACK * BODY WLD ASSY CONNECTOR ASSY HANDLE GUIDE "L" BASE WLD ASSY PLATE BOTTOM LEG 4" FLANGE. BLACK FEET. RUBBER. BLACK TIMER W/SPACER & NUT SWITCH CHERRY W/SCREW STRAIN RELIEF CORD ASSY QTY.
I ORDERING/SERVICE PROCEDURE Use only genuine Bloomfield replacement parts in this Satellite Docking Station. The use of replacement parts other than those supplied by Bloomfield voids the warranty. Parts are available at your Authorized Bloomfield Service Agency as provided in your Warranty Statement and Service Agency Listing. To find. the parts required to restore proper operation to the Satellite Docking Station, proceed as follows: 1.
TROUBLESHOOTING A ELECTRICAL SHOCK HAZARD: Inspecting, testing and repair of electrical equipment should be performed only by qualified service personnel. The Satellite Docking Station should be unplugged when servicing, except when electrical tests are required. Electrical shock will cause serious Injury or death. it is very important, when servicing equipment to: 1. Define the basic problem 2. Isolate the probable cause 3.
TROUBLESHOOTING CORRECTIVE ACTION [ P R O B L E M ][ P R O B A B L E C A U S E ] Quality light lo not on/flashing when Satellite is in place. Satellite Receptical or SDS-l Connector Check Receptical and Connector Assembly, make sure all pins are tight and in place. Check ail soldered wiring. ~ Check continuity, replace if defective. Snap Action Switch in Connector Check continuity, replace if defective.
SCHEMATIC & WIRING DIAGRAM (MODEL SDS-1) MODEL: VOLTS WATTS: SDS-1 120 45 W (USE WITH [1] 9105DS OR 9105DP) 12
13
