001 WELLS BLOOMFIELD, LLC 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wells-mfg.
LIMITED WARRANTY STATEMENT Unless otherwise specified, all commercial cooking equipment manufactured by WELLS BLOOMFIELD, LLC is warranted against defects in materials and workmanship for a period of one year from the date of original installation or 18 months from the date of shipment from our factory, whichever comes first, and is for the benefit of the original purchaser only.
TABLE OF CONTENTS WARRANTY FEATURES & OPERATING CONTROLS PRECAUTIONS & GENERAL INFORMATION AGENCY LISTING INFORMATION INSTALLATION OPERATION CLEANING INSTRUCTIONS TROUBLESHOOTING SUGGESTIONS MAINTENANCE INSTRUCTIONS EXPLODED VIEW & PARTS LIST WIRING DIAGRAM PARTS & SERVICE CUSTOMER SERVICE DATA xi 2 3 3 4 5 6 8 9 10 18 20 21 INTRODUCTION Thank You for purchasing this Wells Bloomfield appliance.
FEATURES & OPERATING CONTROLS A. THERMOSTAT 1. On THERMOSTATICALLY CONTROLLED warmers, power is applied to the heating element according to the control knob position and the actual temperature at the temperature sensing thermobulb. 2. The desired temperature is controlled by rotating the TEMPERATURE CONTROL KNOB. The knob has a numeric scale, where higher numbers correspond to higher temperature. 3. On warmers equipped with an INDICATOR LIGHT, the light will glow when the thermostat is calling for heat (i.
PRECAUTIONS AND GENERAL INFORMATION This appliance is intended for use in commercial establishments only. This appliance is intended to hold pre-heated food for human consumption. No other use is recommended or authorized by the manufacturer or its agents. Operators of this appliance must be familiar with the appliance use, limitations and associated restrictions. Operating instructions must be read and understood by all persons using or installing this appliance.
INSTALLATION NOTE: DO NOT discard the carton or other packing materials until you have inspected the appliance for hidden damage and tested it for proper operation. Refer to SHIPPING DAMAGE CLAIM PROCEDURE on the inside front cover of this manual. WARNING: RISK OF INJURY Installation procedures must be performed by a qualified technician with full knowledge of all applicable electrical and plumbing codes. Failure can result in personal injury and property damage.
OPERATION WET OR DRY OPERATION for WARMERS CAUTION: 1. Carefully read the description of the warmer operation on the specification sheet. 2. a. Most warmers are designed for WET OR DRY operation. b. Warmers may be used wet, or may be used dry. However warmers may NOT be used wet-to-dry or dry-to-wet unless they have been allowed to cool to room temperature between the change in wet or dry operation. c. Wells Manufacturing recommends operating WET for consistent food heating. d.
CLEANING INSTRUCTIONS CAUTION: SHOCK HAZARD Do NOT splash or pour water into or over any control panel or wiring. CAUTION: SHOCK HAZARD DAILY CLEANING INSTRUCTIONS PREPARATIONS: Turn control knob(s) to OFF. Unplug the warmer. Allow warmer to cool before proceeding. Remove any insets, pans and/or adapter tops Drain or remove water from well if used for wet operation. FREQUENCY: Minimum - daily.
CLEANING INSTRUCTIONS (continued) WEEKLY CLEANING INSTRUCTIONS CAUTION: PREPARATIONS: Remove any insets, pans and/or adapter tops. Drain or remove water from well if used for wet operation. FREQUENCY: Weekly, or whenever lime or scale is seen accumulating on the sides of the warmer pans. TOOLS: Commercial Delime Cleaner Plastic Scouring Pad Clean Cloth or Sponge 1. Add water to pans until water is at normal operating level (1” - 1 1/2” deep) or covers accumulated scale. 2.
TROUBLESHOOTING SUGGESTIONS SYMPTOM POSSIBLE CAUSE Circuit breaker off or tripped Reset circuit breaker Unit not plugged in Make sure unit is plugged in to power receptacle Temperature control not set Set control to desired temperature Internal damage Contact you Authorized Wells Service Agency for repairs Pan leaking or other internal damage Contact your Authorized Wells Service Agency for repairs Internal damage Contact your Authorized Wells Service Agency for repairs Mineral deposits on pan
MAINTENANCE INSTRUCTIONS CARE OF STAINLESS STEEL Stainless steel is a marvelous material: strong, lustrous and low maintenance. With a minimum of care, it will normally retain its beauty and durability for the life of the equipment. In some applications, however, special care is required in order to maintain stainless steel’s special properties. External components, such as cabinets and control panels, are finished with a grain pattern.
EXPLODED VIEW: SMPT MODEL SMPT 1 17 16 15 14 13 2 12 3 11 5 9 6 8 MODEL: SMPT 7 IL1927, Rev.
001 p/n 2M-303305 Owners Manual CT Warmers / Thermostat Control PARTS LIST: SMPT MODEL: SMPT FABRICATED WARMER Item No Part No Description 1 2P-38628 PLUG HOLE 5/8 DIA 2E-45061 CORD SET 120V, 15A 14G 2 2E-35540 CORD SET 6-15P 16/3W 4FT 3 2K-31217 STRAIN RELIEF 90DEG 4 D8-303352 BRKT THERMO BULB 5 D8-WL0051 BASE, STD REAR WIRED CORD 6 D8-307895 BAE BTM WIRED CORD 7 2A-33572 FEET ADJ 2IN 8 2R-Y5092 BLK PLASTIC LEG, 4 INCH 9 2R-40498 KNOB ASSY 10 D8-30256 TRIM RING ASSY 11 2T-38968 THERMO K TYPE 12 WS-503370
EXPLODED VIEW: SMPT-27 MODEL SMPT-27 15 1 2 14 13 12 3 11 9 5 6 8 MODEL: SMPT 7 IL1927, Rev.
PARTS LIST: SMPT-27 001 p/n 2M-303305 Owners Manual CT Warmers / Thermostat Control MODEL: SMPT-27 FABRICATED WARMER Item No Part No Description Application 2H-303946 INSUL SIDE BMW-327 427 1 2H-307893 INSULATION FRONT 2 2E-45061 CORD SET 120V 15A 14G 2 2E-35540 CORD SET 6-15P 16/3W 4FT 3 2K-31217 STRAIN RELIEF 90DEG 67-301929 PAN ELEMENT ONLY SMPT-27 4 WS-503840 KIT ELEM PAN W/ELEMENT 5 D8-303352 BRKT THERMO BULB 6 D8-307897 BASE SMPT-27 7 2R-Y5052 BLK PLASTIC LEG, 4" 8 2R-40498 KNOB ASSY 9 D8-30256 TRIM
EXPLODED VIEW: SW-10T MODEL SW-10T 14 13 12 11 10 9 1 3 8 7 6 5 4 MODEL: SW-10T IL1929, Rev.
PARTS LIST: SW-10T MODEL: SW-10T FABRICATED WARMER Item No WS-506272 P2-31878 2E-40469 2K-31217 2A-41946 D8-Z13559 D8-306439 2R-40498 D8-30256 WS-60282 2J-30516 2M-300534 D8-Z12597 D8-40427 Description ELEM, 120V@825W COVER ELEM CORD SET 5-15P 6FT STRAIN RELIEF 90DEG LEG ADJUST 1IN BASE, SHELL CLAMP BULB SW10T KNOB ASSY TRIM RING ASSY THERMO CTRL LIGHT SIGNAL AMBER 240V TRADEMARK DOMED LABEL SHELL WRAP SW10 TOP POT ASSY SW10T 001 p/n 2M-303305 Owners Manual CT Warmers / Thermostat Control 1 2 3 4 5 6 7
EXPLODED VIEW: TMPT MODEL TMPT 14 13 1 12 11 2 10 3 9 4 7 5 6 MODEL: TMPT IL1930, Rev.
PARTS LIST: TMPT MODEL: TMPT FABRICATED WARMER Description Application INSULATION FRONT INSUL SIDE STRAIN RELIEF 90DEG mfg. before 11/2011 BUSHING ST 17-2 mfg.
WIRING DIAGRAM 001 p/n 2M-303305 Owners Manual CT Warmers / Thermostat Control 18
WIRING DIAGRAM 001 p/n 2M-303305 Owners Manual CT Warmers / Thermostat Control HMPGW PARTS LIST PART NO 2N-40526UL P2-307356 2E-30330 2J-35697 2T-40528 DESCRIPTION ELEM 220V, 1650W HMP CORDSET HMPG 120V WENDYS SWITCH ON OFF TOGGLE 20A LIGHT PILOT GREEN 250V THERMO CTRL-185F, HMP WIRING DIAGRAM FOR HMP-G POWER CORD 120V, 60HZ, SINGLE PHASE 240V, 50HZ, SINGLE SWITCH (ON/OFF) 1 4 4 GRN. INDICATOR LIGHT 2 H1 ELEMENT H2 3 OPERATING THERMOSTAT 185 F FIXED REV.
PARTS & SERVICE Always use an inset. DO NOT place food directly into the warmer pan. DESCRIPTION PART NO. ADAPTERS & INSETS ADAPTER TOP, convert SMPT, HW/SMP or 1 side of TMPT to hold three 4 qt. insets 5D-21615 ADAPTER TOP, convert SMPT, HW/SMP or 1 side of TMPT to hold one 7 qt. and one 4 qt. inset DD-21617 ADAPTER TOP, convert SMPT, HW/SMP or 1 side of TMPT to hold one 11 qt. and one 7 qt. inset 5D-21621 ADAPTER TOP, convert SW-10T from 11 qt. inset to 4 qt.
PARTS & SERVICE (continued) DESCRIPTION PART NO. 6 oz. SOUP LADLE DD-47088 *LEGS, 1” Plastic, set of 4 5D-21109 *LEGS, 2” Plastic, set of 4 5D-20605 IMPORTANT: Use only factory authorized service parts and replacement filters. For factory authorized service, or to order factory authorized replacement parts, contact your Wells authorized service agency, or call: LEGS, 4” Plastic Adjustable 2R-Y5092 Wells Bloomfield, LLC LEGS, 4” Metal, Adjustable 2A-Z0314 10 Sunnen Dr., P.O.Box 430129 St.
WELLS BLOOMFIELD, LLC 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wells-mfg.
