001 WELLS BLOOMFIELD, LLC 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.
LIMITED WARRANTY STATEMENT Unless otherwise specified, all commercial cooking equipment manufactured by WELLS BLOOMFIELD, LLC is warranted against defects in materials and workmanship for a period of one year from the date of original installation or 18 months from the date of shipment from our factory, whichever comes first, and is for the benefit of the original purchaser only. personnel. The prices charged by Wells Bloomfield for its products are based upon the limitations in this warranty.
TABLE OF CONTENTS WARRANTY FEATURES & OPERATING CONTROLS PRECAUTIONS & GENERAL INFORMATION AGENCY LISTING INFORMATION INSTALLATION OPERATION CLEANING INSTRUCTIONS TROUBLESHOOTING SUGGESTIONS MAINTENANCE INSTRUCTIONS EXPLODED VIEW & PARTS LIST WIRING DIAGRAM PARTS & SERVICE CUSTOMER SERVICE DATA xi 2 3 3 4 5 6 8 9 10 18 20 21 INTRODUCTION Thank You for purchasing this Wells Bloomfield appliance.
FEATURES & OPERATING CONTROLS A. THERMOSTAT INDICATOR LIGHT TEMPERATURE CONTROL KNOB IL2462 1. On thermostatically controlled warmers, power is applied to the heating element according to the control knob position and the actual temperature at the temperature sensing thermobulb. 2. The desired temperature is controlled by rotating the temperature control knob. The knob has a numeric scale, where higher numbers correspond to higher temperature. 3.
PRECAUTIONS AND GENERAL INFORMATION This appliance is intended for use in commercial establishments only. This appliance is intended to hold pre-heated food for human consumption. No other use is recommended or authorized by the manufacturer or its agents. Operators of this appliance must be familiar with the appliance use, limitations and associated restrictions. Operating instructions must be read and understood by all persons using or installing this appliance.
INSTALLATION WARNING: Risk of injury Installation procedures must be performed by a qualified technician with full knowledge of all applicable electrical and plumbing codes. Failure can result in personal injury and property damage. CAUTION FIRE HAZARD Avoid storing flammable or combustible materials in, on or near the appliance. CAUTION SHOCK HAZARD The ground prong of the electrical cord is part of a system designed to protect you from electrical shock. In the event of internal damage to the warmer.
OPERATION WET OR DRY OPERATION for WARMERS CAUTION: 1. Carefully read the description of the warmer operation on the specification sheet. 2. a. Most warmers are designed for WET OR DRY operation. b. Warmers may be used wet, or may be used dry. However warmers may NOT be used wet-to-dry or dry-to-wet unless they have been allowed to cool to room temperature between the change in wet or dry operation. c. Wells Manufacturing recommends operating WET for consistent food heating. d.
CLEANING INSTRUCTIONS CAUTION: DAILY CLEANING INSTRUCTIONS Shock Hazard PREPARATIONS: Turn control knob(s) to OFF. Unplug the warmer. Allow warmer to cool before proceeding. Remove any insets, pans and/or adapter tops Drain or remove water from well if used for wet operation. Do NOT splash or pour water into or over any control panel or wiring. CAUTION: SHOCK HAZARD FREQUENCY: Minimum - daily.
CLEANING INSTRUCTIONS (continued) WEEKLY CLEANING INSTRUCTIONS CAUTION: PREPARATIONS: Remove any insets, pans and/or adapter tops. Drain or remove water from well if used for wet operation. FREQUENCY: Weekly, or whenever lime or scale is seen accumulating on the sides of the warmer pans. TOOLS: Commercial Delime Cleaner Plastic Scouring Pad Clean Cloth or Sponge 1. Add water to pans until water is at normal operating level (1” - 1 1/2” deep) or covers accumulated scale. 2.
TROUBLESHOOTING SUGGESTIONS SYMPTOM No power to warmer Warmer will not heat Warmer trips circuit breaker Warmer slow to heat POSSIBLE CAUSE SUGGESTED REMEDY Circuit breaker off or tripped Reset circuit breaker Unit not plugged in Make sure unit is plugged in to power receptacle Temperature control not set Set control to desired temperature Internal damage Contact you Authorized Wells Service Agency for repairs Pan leaking or other internal damage Contact your Authorized Wells Service Agency
MAINTENANCE INSTRUCTIONS CARE OF STAINLESS STEEL Stainless steel is a marvelous material: strong, lustrous and low maintenance. With a minimum of care, it will normally retain its beauty and durability for the life of the equipment. In some applications, however, special care is required in order to maintain stainless steel’s special properties. External components, such as cabinets and control panels, are finished with a grain pattern.
EXPLODED VIEW: SMPT MODEL SMPT 1 17 16 15 14 13 2 12 3 18 19 5 11 10 9 8 MODEL: SMPT 7 IL1927, Rev.
PARTS LIST: SMPT MODEL: SMPT FABRICATED WARMER Item No 1 Description Application 2P-38628 PLUG HOLE 5/8 DIA 2E-45061 CORD SET 120V, 15A 14G 2E-35540 CORD SET 6-15P 16/3W 4FT 3 2K-31217 STRAIN RELIEF 90DEG 4 D8-303352 BRKT THERMO BULB D8-WL0051 BASE, STD REAR WIRED CORD D8-307895 BAE BTM WIRED CORD D8-Z15106 BOTTOM SMPTD (DRAIN) 7 2A-33572 FEET ADJ 2IN 8 2R-Y5092 BLK PLASTIC LEG, 4 INCH 9 2R-40498 KNOB ASSY 10 D8-30256 TRIM RING ASSY 11 2T-38968 THERMO K TYPE 12 WS-5033
EXPLODED VIEW: SMPT-27 MODEL SMPT-27 15 1 2 14 13 12 3 4 10 9 5 6 8 MODEL: SMPT-27 7 IL1928, Rev.
PARTS LIST: SMPT-27 MODEL: SMPT-27 FABRICATED WARMER Item No Part No Description Application 2H-303946 INSUL SIDE BMW-327 427 2H-307893 INSULATION FRONT 2 2E-45061 CORD SET 120V 15A 14G 2 2E-35540 CORD SET 6-15P 16/3W 4FT 3 2K-31217 STRAIN RELIEF 90DEG 67-301929 PAN ELEMENT ONLY WS-503840 KIT ELEM PAN W/ELEMENT 5 D8-303352 BRKT THERMO BULB 6 D8-307897 BASE SMPT-27 7 2R-Y5052 BLK PLASTIC LEG, 4” 8 2R-40498 KNOB ASSY 9 D8-30256 TRIM RING ASSY 10 2T-38968 THERMO K TYPE 2N
EXPLODED VIEW: SW-10T MODEL SW-10T 14 13 12 11 10 9 2 3 8 7 6 5 4 MODEL: SW-10T IL1929, Rev.
PARTS LIST: SW-10T MODEL: SW-10T FABRICATED WARMER Item No Part No Description 1 WS-506272 ELEM, 120V@825W 2 P2-31878 COVER ELEM 3 2E-40469 CORD SET 5-15P 6FT 4 2K-31217 STRAIN RELIEF 90DEG 5 2A-41946 LEG ADJUST 1IN 6 D8-Z13559 BASE, SHELL 7 D8-306439 CLAMP BULB SW10T 8 2R-40498 KNOB ASSY D8-30256 TRIM RING ASSY WS-60282 THERMO CTRL 11 2J-30516 LIGHT SIGNAL AMBER 240V 12 2M-300534 TRADEMARK DOMED LABEL 13 D8-Z12597 SHELL WRAP SW10 14 D8-40427 TOP POT ASSY SW10T 00
EXPLODED VIEW: TMPT MODEL TMPT 14 13 1 15 16 12 11 2 3 9 8 4 7 5 6 MODEL: TMPT IL1930, Rev.
PARTS LIST: TMPT MODEL: TMPT FABRICATED WARMER Item No Part No Application 2H-307893 INSULATION FRONT 2H-46073 INSUL SIDE 2K-31217 STRAIN RELIEF 90DEG mfg. before 11/2011 2K-Y3240 BUSHING ST 17-2 mfg.
001 p/n 2M-303305 Owners Manual CT Warmers / Thermostat Control WIRING DIAGRAM 18
WIRING DIAGRAM HMPGW PARTS LIST 001 p/n 2M-303305 Owners Manual CT Warmers / Thermostat Control PART NO DESCRIPTION 2N-40526UL ELEM 220V, 1650W HMP P2-307356 CORDSET HMPG 120V WENDYS 2E-30330 SWITCH ON OFF TOGGLE 20A 2J-35697 LIGHT PILOT GREEN 250V 2T-40528 THERMO CTRL-185F, HMP POWER CORD WIRING DIAGRAM FOR HMP-G 120V, 60HZ, SINGLE PHASE 240V, 50HZ, SINGLE PHASE SWITCH (ON/OFF) ELEMENT 1 4 H1 4 2 H2 GRN. INDICATOR LIGHT 3 OPERATING THERMOSTAT 185 F FIXED REV.
PARTS & SERVICE DO NOT place food directly into the warmer pan. DESCRIPTION PART NO. ADAPTERS & INSETS Adapter top, convert SMPT, HW/SMP or 1 side of TMPT to hold three 4 qt. insets 5D-21615 Adapter top, convert SMPT, HW/SMP or 1 side of TMPT to hold one 7 qt. and one 4 qt. inset DD-21617 Adapter top, convert SMPT, HW/SMP or 1 side of TMPT to hold one 11 qt. and one 7 qt. inset 5D-21621 ADAPTER TOP, convert SW-10T from 11 qt. inset to 4 qt.
PARTS & SERVICE (continued) DESCRIPTION PART NO. ACCESSORIES IMPORTANT: Use only factory authorized service parts and replacement filters. For factory authorized 6 oz.
WELLS BLOOMFIELD, LLC 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.
