Installation & Operation Instructions

ManualsBrandsBLP Technologies ManualsElectrical EquipmentWireless line powered and battery powered wall switch

WIRELESS WALL SWITCH

& LOAD CONTROLLER

INSTALLATION & OPERATION INSTRUCTIONS

MODEL NUMBERS DESCRIPTIONS

SWX-851-xx

WIRELESS WALL SWITCH LOAD CONTROLLER,

120/277VAC, NO NEUTRAL REQUIRED

BASIC OPERATION

A received wireless message indicating occupancy from one or more wirelessly linked

sensors will trigger the unit’s integrated relay to close. When congured for Vacancy

operation, lights must be initially switched on by pressing the unit’s button (or by pressing

the ON button on a wirelessly linked wall station). Once closed, line voltage will ow

through the relay and turn on the connected lighting load. This wall switch load controller

maintains a master time delay that is reset every time a linked sensor reports occupancy.

Lights will be switched off once there hasn’t been an occupancy message reported for the

duration of the time delay.

* xx = color (WH, IV, AL, GY)

SPECIFICATIONS

ELECTRICAL

OPERATING VOLTAGE

120-277 VAC, Single Phase, 50/60 Hz

LOAD RATINGS

MAX: 800W @ 120VAC

1200W @ 277VAC

MIN: None

LOAD TYPES

LED Driver/Lamps

CFL, Electronic/Magnetic Ballasts

(Fluorescent)

Tungsten (Incandescent)

ESD IMMUNITY

Tested to withstand electrostatic

discharge without damage or

memory loss.

SURGE IMMUNITY

Tested to withstand surge voltages

without damage or loss of operation.

NON-VOLATILE MEMORY

Saves all settings even if power is

disrupted.

ENVIRONMENTAL

OPERATING TEMP

32°F to 122°F (0°C to 50°C)

RELATIVE HUMIDITY

0-95% Non-Condensing, Indoor Use

Only

OPERATION

OPERATING MODES

Occupancy, Vacancy, Switch Disable

TIME DELAY OPTIONS

1, 5, 10, 15, 20, 30 min.

WIRELESS

RANGE

80’ line of site w/o obstruction (walls)

40’ with obstruction (walls/oors)

FREQUENCY

915 MHz ISM Band

WIRELESS LINKING

Simple 3 sec. Push Button Process

SECURITY

All Wireless Data is Encrypted

PHYSICAL

SIZE

2.74”H x 1.68”W x 1.39”D

(6.96 x 4.27 x 3.53 cm)

<1” Wallbox Mounting Depth

WEIGHT

4.5 oz

MOUNTING

Single Gang Switch Box

LED STATUS INDICATOR

Bi-color White & Blue

CODE COMPLIANCE

These load controllers can be used to

meet ASHRAE 90.1, IECC, & Title 24

energy code requirements.

OVERVIEW

The SENSORWORX wireless wall switch load controller links to remote occupancy

sensors and switches without low voltage wiring in order to provide automatic lighting

control. Designed with contractors in mind, the unit is signicantly shallower than typical

wall controllers, resulting in less crowded wall boxes. Additionally, versatile wiring

enables usage with or without a neutral connection and never requires a minimum load.

This switch also matches the SENSORWORX family of wall switch occupancy sensors

and 0-10V dimming wall switch sensors. All SENSORWORX products are proudly made

in the USA.

FEATURES

ELECTRICAL FEATURES

Ã Accommodates Neutral (3-Wire) and No-Neutral (2-Wire) Installations

Ã Electronically Timed Switching Ensures Long Relay Life

Ã No Minimum Load or External Load Capacitor (MLC) Requirements

Ã Meets Regulatory Guidelines for Current Leakage

PHYSICAL FEATURES

Ã Enclosure is 25-40% Shallower than Other Wall Controllers (< 1” Depth into

Wallbox)

Ã Self-Grounding Mounting Strap

Ã Modern Look and Intuitive Easy-Tap Button

OPERATIONAL FEATURES

Ã Pairs in Seconds with Wireless Sensors & Remote Wall Stations

Ã Conﬁgurable Time Delays and Operational Modes (e.g. Occupancy, Vacancy,

Switch Disable)

Ã Blue Locator LED when Lights are Off

Ã Settings are Adjustable Without Removing Cover Plate

Ã Links with up to 30 sensors and/or switches

Summary of content (7 pages)

PAGE 1
WIRELESS WALL SWITCH & LOAD CONTROLLER INSTALLATION & OPERATION INSTRUCTIONS MODEL NUMBERS DESCRIPTIONS SWX-851-xx WIRELESS WALL SWITCH LOAD CONTROLLER, 120/277VAC, NO NEUTRAL REQUIRED * xx = color (WH, IV, AL, GY) OVERVIEW The SENSORWORX wireless wall switch load controller links to remote occupancy sensors and switches without low voltage wiring in order to provide automatic lighting control.
PAGE 2
INSTALLATION INSTRUCTIONS Ã Designed to mount in 1-gang wall box with 3.28” hole spacing. Ã Units can also share multiple gang wall boxes with other devices. Ã Unit face is field removable in order to change colors. Contact factory for additional faces. FRONT SIDE SUPPLIED MOUNTING SCREWS FOR MOUNTING TO SINGLE GANG SWITCH BOX BREAK-OFF BRACKET EARS LED INDICATOR SENSOR FACE ** 2.74” BUTTON BREAK-OFF BRACKET EARS 1.69” 0.94” 1.39” ** SENSOR FACE IS FIELD REMOVABLE IN ORDER TO CHANGE COLORS.
PAGE 3
APPLICATIONS (CONT.) COMPATIBLE WIRELESS DEVICES The below chart lists the devices that can be used in a SENSORWORX wireless application. Note that sensors and remote switch & dimmer devices are transmit only devices and therefore must be linked to a load controller for switching or dimming of lighting.
PAGE 4
CONFIGURATION SETTINGS All configuration settings for the wireless wall switch load controller are organized into several parameter functions with values that can be accessed and changed by pressing the unit’s push-button and observing the LEDs feedback. FUNCTION #2 OCCUPANCY TIME DELAY Unlike wired occupancy sensor systems, the time frame between when occupancy was detected last and connected lights turning off is a setting that is maintained in the load controller and not the sensor itself.
PAGE 5
CONFIGURATION SETTINGS (CONT.) FUNCTION #3: OPERATIONAL MODES Wireless wall switch load controllers have several sequence of operation choices. SETTING # 2 3 4* 5 MODE DESCRIPTION Vacancy Mode Pressing the unit’s button (or an ON button push on a linked wireless switch) is required to initially turn lights on. Lights will turn off automatically if the OCCUPANCY TIME DELAY (Function #2) expires between received occupied messages from a sensor.
PAGE 6
CONFIGURATION SETTINGS (CONT.) FUNCTION #5: RELAY ENABLE/DISABLE If the wall switch load controller is being used as a remote switch for another load controller and not controlling a lighting load of its own, the relay can be disabled. To disable, follow the below steps. SETTING # DESCRIPTION 2 Relay enabled (default) 3 Relay disabled (i.e.
PAGE 7
FCC INFORMATION (FCC ID: 2AVRY-SWX0001) This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1. This device many not cause harmful interference, and 2. This device must accept any interference received, Including interference that may cause undesired operation Changes and Modifications not expressly approved by BLP Technologies can void your authority to operate this equipment under Federal Communications Commission’s rules.