User Manual

TECHNICAL SPECIFICATIONS
BT Version: 5.0 with aptX HD
Supported Codecs: aptX, aptX Low Latency, aptX HD, SBC, AAC,
MP3, FLAC, TFF.
BT Range: 30 meters, 100 feet
Input: BT
Outputs: Stereo Analog RCA; Digital Optical & Coaxial (SPDIF)
Input Power: Power Requirement: DC 5V (USB), 200mA (Min), 3A (Max)
Output Voltage: 2.1 Volts RMS
Output Impedance: 57 Ohms
D/A Converter: TI PCM5102A
Frequency Response: 10Hz - 20kHz (+/- 0.5dB)
Signal to Noise Ratio: 112dB
Total Harmonic Distortion: + Noise < 0.02%
Latency: ~30 milliseconds (MS)
Enclosure: Aluminum + ABS
To reduce the risk of electric shock
Do not remove cover (or back).
No user-serviceable parts inside.
Refer servicing to qualified service personnel.
9.9cm
2.5cm
7.5cm
Included Accessories:
• RCA - RCA Audio Cable
• RCA - 3.5mm Audio adapter
• USB - micro USB Cable
• TOSLINK optical audio cable
• User Guide
DESIGNED IN AUSTRALIA – MADE IN CHINA BLUDENTO INC.
©2021 BluDento, Inc. All Rights Reserved.
Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or
its subsidiaries. Qualcomm is a trademark of Qualcomm Incorporated,
registered in the United States and other countries. aptX is a trademark of
Qualcomm Technologies International, Ltd., registered in the United States
and other countries.
NOT included:
• Coaxial audio cable
• Power plug USB 5V DC(0.2A - 3.0A)
TROUBLESHOOTING TIPS
My device does not pair with BLT-HD.
• Ensure that BT is turned ON on your device.
• Make sure that the LED indicator is blinking and your device is as close to
BLT-HD as possible.
• Restart the BLT-HD and cycle BT on your device in order to
re-establish the connection.
The LED Indicator is solid, but I cannot connect my device.
• Check whether no other devices are connected. If so, either disconnect or
turn off BT on the other devices till it flashes, then try connecting.
• Close the BT function of all your BT devices and open
them again.
The sound quality is poor and / or the audio is cutting out.
• Move your device or BLT-HD away from cordless phones, routers,
microwave ovens or other BT devices.
• Try moving your device closer to BLT-HD.
• Turn off your device’s Wi-Fi.
• Try unpairing and repairing your device to BLT-HD.
• Check that your device’s OS is updated to the latest version.
Only one channel plays music.
• Check the cables between BLT-HD and your stereo system.
• Check your BT device, music player APP and home theater to ensure
that the audio balance is centered.If you have any further queries please
contact us on [e-mail]
The LED indicator is solid and my device is connected but there
is no audio output.
• Ensure that the BLT-HD output is correctly connected to your audio system.
• Check whether the audio source is correctly selected on your music system
(Analog audio or digital optical/coaxial input).
• Verify the volume levels on your BT device, player APP and home theater.
Please confirm all are not mute
• Try unpairing and repairing your device to BLT-HD.
The volume output level from BLT-HD is Low.
• Verify the volume levels on your BT device, player APP.
• Also check the volume levels on your powered speakers or stereo system.
Please confirm all are not on mute.
WARRANTY
Don’t worry. Your BluDento BLT-HD is covered under our warranty. For warranty
information please visit:http://bludento.com/contact-bludento/
www.bludento.com
[e-mail]
PRODUCT SAFETY
When used in the directed manner, this unit has been designed and
manufactured to ensure your personal safety. Improper use of this product
can result in potential electrical shock or fire hazards. Please read all safety
and operating instructions carefully before installation and use. Keep these
instructions handy for future reference.
Users of this product are cautioned not to make modifications or changes
that are not approved by BluDento, Inc. Doing so may void the compliance of
this product and may result in the loss of the user’s authority to operate the
equipment.