Manualshelf

Installation Guide

ManualsBrandsBlue Flame ManualsPlumbingMulti-Functional Valve
12
VALVE SETTING FOR WOOD-BURNNG FIREPLACE:
1. Turn valve to OFF position by turning key, #1 clockwise until it stops.
2. Remove key, #1.
3. Loosen set screw, #2 using Allen Wrench, #3 (included), so the inner
adapter, #4 is free.
4. Rotate inner adapter, #4 so the roll pin, #5 is in the middle (22,000
Btu/hr-1/4 turn) of the sliced opening of the inner adapter #4.
5. Tighten set screw, #2.
6. Once the valve is installed, insert key, #1 and turn counterclockwise
to turn ON and clockwise to turn OFF.
VALVE SETTING FOR SMALL ARTIFICIAL LOG SETS:
1. Turn valve to OFF position by turning key, #1 clockwise until it stops.
2. Remove key, #1.
3. Loosen set screw, #2 using Allen Wrench, #3 (included) so the inner
adapter, #4 is free.
4. Rotate inner adapter, #4 counterclockwise, so the roll pin, #5 is at the end
(44,000 Btu/hr-1/2 turn) of the sliced opening of the inner adapter, #4.
5. Tighten set screw, #2.
6. Once the valve is installed, insert key, #1 and turn counterclockwise to
turn ON and clockwise to turn OFF.
VALVE SETTING FOR FIRE PITS:
1. Turn valve to OFF position by turning key, #1 clockwise until it stops.
2. Remove key, #1.
3. Loosen set screw, #2 using Allen Wrench, #3 (included) so the inner
adapter, #4 is free for BTU’S of up to 270,000.
4. Once valve is installed, insert key, #1 and turn counterclockwise to
turn ON and clockwise to turn OFF.
www.blueflamestore.com 800-321-6566
Please note: Each application can vary from fire pit to fire pit, depending on their
designs. The valve should be supported and protected from outside elements such as
heat, sun, and rain. Installation of valve should comply with applicable standards.
www.blueflamestore.com 800-321-6566
VALVE SETTING FOR WOOD-BURNNG FIREPLACE:
1. Turn valve to OFF position by turning key, #1 clockwise until it stops.
2. Remove key, #1.
3. Loosen set screw, #2 using Allen Wrench, #3 (included), so the inner
adapter, #4 is free.
4. Rotate inner adapter, #4 so the roll pin, #5 is in the middle (22,000
Btu/hr-1/4 turn) of the sliced opening of the inner adapter #4.
5. Tighten set screw, #2.
6. Once the valve is installed, insert key, #1 and turn counterclockwise
to turn ON and clockwise to turn OFF.
VALVE SETTING FOR SMALL ARTIFICIAL LOG SETS:
1. Turn valve to OFF position by turning key, #1 clockwise until it stops.
2. Remove key, #1.
3. Loosen set screw, #2 using Allen Wrench, #3 (included) so the inner
adapter, #4 is free.
4. Rotate inner adapter, #4 counterclockwise, so the roll pin, #5 is at the end
(44,000 Btu/hr-1/2 turn) of the sliced opening of the inner adapter, #4.
5. Tighten set screw, #2.
6. Once the valve is installed, insert key, #1 and turn counterclockwise to
turn ON and clockwise to turn OFF.
VALVE SETTING FOR FIRE PITS:
1. Turn valve to OFF position by turning key, #1 clockwise until it stops.
2. Remove key, #1.
3. Loosen set screw, #2 using Allen Wrench, #3 (included) so the inner
adapter, #4 is free for BTU’S of up to 270,000.
4. Once valve is installed, insert key, #1 and turn counterclockwise to
turn ON and clockwise to turn OFF.
Please note: Each application can vary from fire pit to fire pit, depending on their
designs. The valve should be supported and protected from outside elements such as
heat, sun, and rain. Installation of valve should comply with applicable standards.
# 4
Inner
Adapter
#2 Set
Screw
#1 Key
#3 Allen Wrench
# 5
Roll Pin
Please keep these instructions for future use and future home owners
Artificial log set
Setting
Wood - Burning
Setting
# 5
Roll Pin
Wood - Burning
Setting
Please keep these instructions for future use and future home owners
Artificial log set
Setting
#1 Key
#3 Allen Wrench
#2 Set
Screw
# 4
Inner
Adapter

Summary of content (2 pages)