Use and Care Manual

ManualsBrandsBlue Max ManualsOutdoors2-in-1 Portable 8 in. Corded Electric Chainsaw with Telescoping Pole

88052959 09/13

Telescoping Pole Saw/Chainsaw

For Customer Service, please call 1-800-348-5004 or

email feedback@natitools.com

Model: 52959

CALIFORNIA PROPOSITION 65

WARNING: You can create dust

when you cut, sand, drill or grind

materials such as wood, paint,

metal, concrete, cement, or other

masonry. This dust often contains

chemicals known to cause cancer,

birth defects, or other

reproductive harm. Wear

protective gear.

WARNING: This product or its

power cord may contain

chemicals, including lead, known

to the State of California to cause

cancer and birth defects or other

reproductive harm. Wash hands

after handling.

Important!

When using equipment, a few safety

precautions must be observed to

avoid injuries and damage. Please

read the complete operating manual

with due care. Keep this manual in a

safe place, so that the information is

available at all times. If you give the

equipment to any other person, give

them these operating instructions as

well. We accept no liability for

damage or accidents which arise due

to non-observance of these

instructions and the safety

information herein.

CAUTION:

FOR YOUR OWN SAFETY READ

INSTRUCTION MANUAL

COMPLETELY AND CAREFULLY

BEFORE OPERATING THIS

BRUSH CUTTER/STRING

TRIMMER.

SPECIFICATIONS

Motor Amp: 6.25 Amp

Bar Length: 8”

Comfort Grips

Maximum Extension: 10 ft.

Voltage:120V

Idle Speed: 800 RPM

Oregon® Bar & Chain

Any failures made in following the

safety regulations and and

instructions may result in an

electric shock, fire and/or serious

injury.

UNPACK

1. Unpack all parts and lay them on

a flat, stable surface.

2. Remove all packing materials and

shipping devices if applicable.

3. Make sure the contents are

complete and free of damage. If

you find that parts are missing or

damaged, contact your dealer.

Using an incomplete or damaged

product may cause damage to

people or property.

4. Ensure you have all the

accessories and tools needed for

assembly and operation. This also

includes suitable personal

protective equipment.

INTENDED/NON-INTENDED USE

: POLE SAW

The pole saw is intended for cutting

trees and other wood from the

ground. It must only be operated in

the garden area. Do not use it for

any purpose that it was not

intended. The pole saw is intended

to be operated in the way specified

in this instruction manual. Read

and observe instructions and

warning signs attached to the

machine before every use. It is

intended to be used with original

spare parts or spare parts

authorized by the manufacturer. If

non-authorized spare parts or non-

original spare parts, the warranty

will be voided. The operator is

liable for any resulting injuries or

damages.

Summary of content (15 pages)

PAGE 1
Telescoping Pole Saw/Chainsaw CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear. WARNING: This product or its power cord may contain chemicals, including lead, known to the State of California to cause cancer and birth defects or other reproductive harm.
PAGE 2
RESIDUAL RISKS Even when using this product properly, there remains certain residual risks that cannot be eliminated.
PAGE 3
•If operating a power tool in a damp switch does not turn it on and off. Any location is unavoidable, use a residual power tool that cannot be controlled current device (RCD) protected with the switch is dangerous and supply. must be repaired. 3. Personal Safety • Disconnect the plug from the power • Stay alert. Watch what you are doing source and/or the battery pack from the power tool before making any and use common sense when adjustments, changing accessories, operating a power tool.
PAGE 4
contact with the moving saw chain. 9. Follow instructions for lubricating, chain tensioning, and changing accessories. Improperly tensioned or lubricated chain may either break or increase the chance for kickback. 10. Keep handles clean, dry, and free from oil and grease. Greasy, oily handles are slippery causing loss of control. 11. Only cut wood. Do not use chainsaw for purposes not intended. For example: do not use chainsaw for cutting plastic, masonry, or non-wood building materials.
PAGE 5
• The user must wear appropriate clothing when operating this machine, such as non-skid footwear and form-fitting clothing. • Do not use this machine if you are tired, ill, or under the influence of drugs or alcohol. • When using this machine, keep bystanders away. Be careful of falling branches. • Be careful when transporting. Use the protective cover in order to transport and store the device. ASSEMBLE THE POLE SAW Assemble the pole saw rear handle 1.
PAGE 6
Assemble the front handle 1. Turn the clamp (c) to the front handle (a). 2.Insert the front handle (a) on the clamp (c) and adjust it to a comfortable position. 3. Fixing the front handle by turning the knob (b). Connection to the power supply and mounting of the extension cable This product adapts to voltages of 120V. Note: Use only connection or an extension cable with a maximum length of 100 ft. and a minimum cable diameter of 12 gauge.
PAGE 7
5. Use the wrench to adjust the chain tension. The drive links of a correctly tensioned warm chain will hang approximately 3-4mm out of the bar groove. ASSEMBLE THE CHAINSAW Loosen the knob to remove the chainsaw cutting head from the pole saw telescopic tube, 2. Place the bar onto the bar stud so that the chain tensioning pin fits into the chain tensioning pin hole. Fit the chain over the sprocket and into the bar groove.
PAGE 8
Step 5: After inserting the cutting head in the handle enclosure, press the knob. The metal rod which connected with the knob will protrude from the hand enclosure to lock the cutting head and handle enclosure together. Step 2: If the brake guard of the chainsaw handle is in the brake position, reset the brake guard to the non-brake position.
PAGE 9
Meanwhile, the connection of the metal trigger causes the safety switch in the handle enclosure to close the electrical circuit. Step 7: After completing steps 1-6, the chainsaw is ready to be used as you would an ordinary handheld electric chainsaw. HOLDING THE CHAINSAW Always hold the chainsaw with your right hand at the rear handle and your left hand at the front handle. Grip both handles with the thumbs and fingers encircling the handles. STARTING OPERATION Start the machine.
PAGE 10
Make the felling back cut at least 2 in. higher than the horizontal notching cut. Keep the felling back cut parallel to the horizontal notching cut. Make the felling back cut so as to leave enough wood to act as a hinge. The hinge wood keeps the tree from twisting and falling in the wrong direction. Do not cut through the hinge. As the felling cut gets close to the hinge, the tree should begin to fall.
PAGE 11
MAINTENANCE Maintenance and sharpening • When the chain is properly sharpened, the work is not tiring, the cutting yield is high, and there is no abnormal wear on the mechanical parts or the bar • Before sharpening, the chain must be made taught by means of the chain tensioner • After sharpening, slacken the chain as per the mounting instructions. • During sharpening, lock the chain, using the brake.
PAGE 12
North American Tool Industries (NATI) makes every effort to ensure that this product meets high quality and durability standards. NATI warrants to the original retail consumer a 1-year limited warranty from the date the product was purchased at retail and each product is free from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, or accidents, repairs or alterations, or a lack of maintenance.
PAGE 13
Telescoping Pole Saw/Chainsaw Model: 52959 For Customer Service, please call 1-800-348-5004 or email feedback@natitools.
PAGE 14
Parts List For customer service, call 1-800-348-5004 or e-mail feedback@natitools.
PAGE 15
Parts List # Description # Description 1 Rear Handle 12 Front Hand Guard 2 Front Handle 13 Oil Tank Lid 3 Lock Button 14 Transportation Cover 4 Switch Trigger 15 Oil Tank 5 Handle Adjustment Button 16 Locking Knob 6 Harness 17 Plug 7 Fixing Knob 18 Power Cord 8 Front Handle Knob 19 Cable Hook 9 Length Adjustment Knob 20 Sprocket 10 Guide Bar 21 Guide Bar Cover 11 Saw Chain 22 Chain Tension Adjusting Screw feedback@natitools.