Installation Guide

ManualsBrandsBlue Wave ManualsOutdoorsBelize 21 ft. x 41 ft. Oval 52 in. Deep 6 in. Top Rail Metal Wall Swimming Pool Package

UNIVERSAL INSTRUCTIONS

BRACED OVAL POOLS

PLEASE READ THESE INSTRUCTIONS CAREFULLY AND THOROUGHLY BEFORE

STARTING GROUND PREPARATION AND POOL ASSEMBLY.

DOING SO WILL PREVENT PROBLEMS.

Oval Pool: General informaition -----------------------------------

1) Selection pool site -----------------------------------------------

2) Ground preparation ----------------------------------------------

3) Assembling side vertical,Horizontal support and brace-

4) Drawing pool shape ----------------------------------------------

5) Connecting tension straps --------------------------------------

6) Positioning assembled oval parts -----------------------------

7) Assembling bottom rail ------------------------------------------

8) Installing wall -------------------------------------------------------

9) Build an earth mound(Cove) -----------------------------------

10) Through the wall skimmer --------------------------------------

11) Liner installation ---------------------------------------------------

Please refer to "Assemble TopSeat , Vertical and Cover" of an attached sheet.

12) Filling the pool -----------------------------------------------------

13) Helpful information -----------------------------------------------

14) SAFETY RULES --------------------------------------------------

BRACED OVAL Parts List (#A OVAL CARTON) --------------

Page.

Summary of content (12 pages)

PAGE 1
UNIVERSAL INSTRUCTIONS BRACED OVAL POOLS PLEASE READ THESE INSTRUCTIONS CAREFULLY AND THOROUGHLY BEFORE STARTING GROUND PREPARATION AND POOL ASSEMBLY. DOING SO WILL PREVENT PROBLEMS. Page.
PAGE 2
GENERAL INFORMATION Before attempting to set up the pool, read the entire instructions. There are certain areas in the instructions that are extremely important to follow exactly as written and/or pictured. Any deviation from these instructions voids warranty of the pool and could cause bodily harm or damage to your property.
PAGE 3
2) GROUND PREPARATION b) Remove all grass from within the entire pool area. It is not enough to just cut the grass. The sod must be removed. (8262mm) 41x21 27' 1-1/4" (52" Wall) (8161mm) 26' 9-1/4" (6401mm) 21' a) Mark off your pool area by driving stakes. Have a helper hold a tape measure or a string and mark off the pool perimeter using flour or chalk. Remove sod inside the pool area to a distance of 1 feet beyond dimensions shown in the plot layout around entire perimeter of pool.
PAGE 4
3 #12 Sheet Metal Screw P.No.0341 3/4 (Packed #3 Package) STEP2; Connect brace to side vertical. Put M8x20 hex head bolt with Plain Washer from outside then put M8 nut from insaide AND 1/4"X1/2" truss head screw from outside then P.No.3177 put 1/4" nut from inside, Do not fasten Resin Side Upper Joint tightly. STEP1; Connect side vertical to horizontal support. Put M8x20 hex head bolt with Plain Washer from outside then put M8 nut from inside, Do not fasten tightly.
PAGE 5
4 P.No.7224 End Strap P.No.0623 M8 Nut P.No.0923 M8 x 20 Hex Head Bolt STEP4 P.No 3234 Resin Side Lower Rail Joint (5/8in Rail) P.No.3223 Resin Side Lower Rail Joint (1in Rail) #12 Sheet Metal Screw P.No.0341 3/4 P.No.0623 M8 Nut STEP1 P.No.0923 M8 x 20 Hex Head Bolt 20mm P.No.0623 M8 Nut P.No.0423 Plain Washer P.No.0923 M8 x 20 Hex Head Bolt P.No.0423 Plain Washer P.No.5238 Horizontal Support For 48" P.No.5239 Horizontal Support For 52" P.No.0423 Plain Washer P.No.0623 M8 Nut P.No.
PAGE 6
(4847mm) 4) DRAWING POOL SHAPE 15' 10-7/8" Wall -1 m ) /8 " ( 5' 1806 11 m 5' 7-5/8" (3611mm) 11' 10-1/8" 5 ) m " 6m /8 80 -1 (1 '11 Side Vertical (1717mm) Please Draw a line with seeing the picture of each pool size.
PAGE 7
(12520mm) (3 " 10 200m ' 6 m) 10' 2-7/8" 21' (6401mm) 1 ) m 0m 6" 20 ' (3 0 (3120mm) 41' 1" (765mm) 2' 6-1/8" (1530mm) 5' 1/4" (1530mm) (1530mm) (765mm) 5' 1/4" 5' 1/4" 2' 6-1/8" (6120mm) (7 74 " 25 7mm '5 ) 20' 1" 41x21 Digging holes; Dig holes for each horizontal support as shown right. inside of pool from "X" point 12 1/2" length. Dig holes where center of patio blocks can be placed at 40" from "X"point for 48" height wall,42" for 52" height wall, width is 5" depth is 2".
PAGE 8
5) CONNECTING TENSION STRAPS This end should be connected to horizontal support. End strap Use #0106.PACK Strap Bolt Package Use #0105.PACK Strap Bolt Package Middle strap 20mm P.No.0623 M8 Nut P.No.0923 M8 x 20 Hex Head Bolt Connect type(B) strap(s) to already assembled type(A) straps. using five sets of M8x20mm hex headed bolt and M8 nut. End strap; 7224 . Those should be used for the end. Middle strap; 7254, 7244, 7264 or 7285. Those should be used for the middle.
PAGE 9
7) ASSEMBLING BOTTOM RAIL STEP 1: Before proceeding, remove the steel wall from carton and stand on a 3'x3' board inside pool area as shown at down. Put the liner, (leaving it in the carton) inside pool area. STEP 2: Bottom rails between the horizontal supports are set up by inserting each end of bottom rail into side lower joint,Insert the bottom rails around the entire perimeter using lower joints on the circular portion of the pool.
PAGE 10
Step 2: Unfold the liner inside the metal wall. Carefully spread it out on the ground. The seam around the bottom of the liner should be well up the earth mound. Do this evenly all around pool. Step 3: Remove top rail temporarily placed. Lift the side of the liner over the top of the wall. Form a collar approximately 3" down the outside of the wall and temporarily tape it, to the outside of the wall using masking tape at intervals of 3'.
PAGE 11
13) HELPFUL INFORMATION 14) SAFETY RULES 1. 1. Read your instructions and safety rules carefully. If you do not follow the safety rules someone could be injured or damage could occur. 2. Plan carefully where you are going to put your pool. It must be close to a water source for filling. Also think about draining your pool. 3. Never let anyone swim alone. Children must be carefully watched. For added safety, install a convex type mirror above pool to give full view of interior.
PAGE 12
BRACED OVAL PARTS LIST 16x12x48 20x12x48 24x12x48 25x15x48 30x15x48 33x18x48 41x21x48 RG11-A (48") CARTON 3313 4105 5238 6254 Side Vertical (48" Wall) Brace (For 48" Wall) Horizontal Support (48" Wall) Pressure plate L=680mm(26-3/4") 2 2 2 2 4 4 4 4 6 6 6 6 4 4 4 4 6 6 6 6 6 6 6 6 8 8 8 8 7224 7254 7244 7264 7285 End Strap L=1400mm(55-1/8") Middle strap L=835mm(32-7/8") Middle strap L=929mm(36-5/8") Middle strap L=1405mm(55-3/8") Middle strap L=1287mm(50-5/8") 2 1 4 2 6 3 4 6 6 8 4