Full Product Manual

ManualsBrandsBlue Wave ManualsAutomatic Pool CleanersAquafirst Super Rover Robotic Pool Cleaner

QUICK START

ITEM: 820411

Thank You

Thank You for entrusting us with keeping your pool clean. We strive

to enhance your pool experience by keeping your pool environment

healthy for you, your family and your friends. Please read this Quick

Start Manual in its entirety to ensure proper operation and care of your

cleaner. Please feel free to leave a review online.

IMPORTANT:

PLEASE READ BEFORE OPERATING CLEANER

• SAFETY INSTRUCTIONS

• WHAT TO EXPECT

• QUICK START

• POWER SUPPLY

• HOW TO GUIDE

• TROUBLESHOOTING

QUICK START OPERATOR MANUAL

FOR THE FOLLOWING CLEANERS

ENG ESP FRA DEU ITL POR

Summary of content (8 pages)

PAGE 1
QUICK START ENG ESP FRA DEU ITL POR QUICK START OPERATOR MANUAL FOR THE FOLLOWING CLEANERS Thank You Thank You for entrusting us with keeping your pool clean. We strive to enhance your pool experience by keeping your pool environment healthy for you, your family and your friends. Please read this Quick Start Manual in its entirety to ensure proper operation and care of your cleaner. Please feel free to leave a review online.
PAGE 2
ENG ESP FRA DEU ITL POR WARNINGS & SAFETY PROCEDURES • A Ground Fault Current Interrupter (GFCI) outlet must be installed to protect your electric outlet and prevent any possible electric shock. • The connection to the branch circuit should be consistent with local and national wiring electrical codes. • To prevent possible electric shock hazard this unit must be connected to an RCD (Residual Current Device) with a related residual operating current not exceeding 30mA.
PAGE 3
ENG ESP FRA DEU ITL POR WHAT TO EXPECT YOUR ROBOT’S TYPICAL CLEANING METHOD Your robotic pool cleaner is designed to clean the dirt and debris from the pool bottom; and in some pools the cove and lower wall . Below is the typical pattern your cleaner will attempt in your pool. Pool dimensions and cleaning surfaces vary from pool to pool so coverage and cleaning patterns may vary. • In pools that have 90 degree pool floor to wall transitions, this cleaner will clean the pool floor.
PAGE 4
ENG ESP FRA DEU ITL POR QUICK START 1 2 *Please see Page 5 for power supply variations. Straighten out the floating cable. Then lift the flap on the power supply. Plug in the cable. Plug power supply into a GFCI outlet (Ground Fault Circuit Interrupter) (Power Supply must be 12 ft. from the pool’s edge) 3 4 Place the cleaner in your pool in the shallow end and turn upside down to remove any air bubbles. Let the cleaner fall to the bottom of the pool right side up.
PAGE 5
ENG ESP FRA DEU ITL POR POWER SUPPLY OPERATION STANDARD POWER SUPPLIES Your cleaner is equipped with one of the power supplies illustrated in this section 1 Press this button first to activate the power supply This button turns the power supply ON / OFF. ON / OFF Press the switch into the ON position. The light will illuminate red on the switch. The cleaning cycle will run a for two (2) hours and automatically turn off when complete. Press the SELECT Button after turning the power supply ON.
PAGE 6
ENG ESP FRA DEU ITL POR HOW TO... ENSURE POOL COVERAGE & PREVENT CABLE TANGLING To change the angle and direction of the cleaning path simply alternate the pins located underneath the bottom of the cleaner. We recommend to change the direction every cleaning cycle to ensure the cleaner is covering the whole pool as well as to prevent cable tangling. Axle Position Axle Position Adjustable Pin Axle Position Axle Position Fixed Pin CLEAN THE FILTERS 1 2 ALL MODELS Push tabs down and outward.
PAGE 7
ENG ESP FRA DEU ITL POR EXTEND THE LIFE OF YOUR CLEANER Your pool cleaner does a lot of work behind the scenes during the season. To help you get the most out of your product, we’ve listed some important tips on how to extend the life of your pool cleaning investment. Take care of your robot and it’ll take care of you. TIP #1: DO NOT DROP THE UNIT OR POWER SUPPLY! Dropping your cleaner or power supply will cause damage and your robot will not work properly.
PAGE 8
ENG ESP FRA DEU ITL POR TROUBLESHOOTING MOVES SLOWLY OR DOESN'T SEEM TO BE VACUUMING • The solution is to make sure that the filter bag is clean. • Check to see that the suction ports are not clogged or blocked. ALL LED LIGHTS ARE BLINKING ON THE POWER SUPPLY • Check to see if the unit is out of water. • Check to see if the filter bag is stuck in the motor protection screen. • Check to see if the propeller is stuck. • To restart, press the power button once.