Instructions / Assembly

ManualsBrandsBlue Wave ManualsKitchenLow Mount Spa Cover Lift

Table Of Contents

LOW MOUNT SPA COVERLIFT

Installation Instructions

CUSTOMER SERVICE HOTLINE: 1-800-759-0977

BlueWave, 1745 Wallace Ave., St. Charles, IL 60174

!! CAUTION !!

IMPORTANT!! READ ALL INSTRUCTIONS CAREFULLY

BEFORE BEGINNING INSTALLATION

Please read all instructions and

precautions in this installation sheet

before using this equipment. Save this

installation sheet for future reference.

Use this Spa Coverlift only as described

in this installation sheet. Inspect and

tighten all parts regularly, replace any

worn or missing parts immediately.

!! WARNING !!

Adult assembly required. This package

contains small parts which are a

choking hazard. Keep children away

from bags and parts until assembled.

Dispose of packaging with care.

(Spa and Spa Cover Not Included)

ITEM NUMBER: NP5022

-1 -

Mfg#3200103

DO NOT attach o r incorporate e lectrical app liances or accessories into or onto T he Spa Coverlift as an

electrical hazard could be created, resulting in injury or death.

DO NOT lean, sit, stand on or play around The Spa Coverlift that could cause a loss of balance resulting in

injury.

Use of The Spa Coverlift for any application other than fo r wh ich it was designed is solely at th e

purchaser’s

risk and Blue Wave will not be held liable for such use resulting in injur y, property damage or

damage to the product.

Summary of content (6 pages)

PAGE 1
LOW MOUNT SPA COVERLIFT Installation Instructions IMPORTANT!! READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION ITEM NUMBER: NP5022 Mfg#3200103 (Spa and Spa Cover Not Included) !! CAUTION !! Please read all instructions and precautions in this installation sheet before using this equipment. Save this installation sheet for future reference. Use this Spa Coverlift only as described in this installation sheet.
PAGE 2
BEFORE YOU GET STARTED You will need to make sure you have at least 2 feet of clearance of all 4 sides of your spa. We reco mmend the coverlift opens towa rd the back of the spa away fro m the contro l panel. Mounting the coverlift in an y othe r o rientation may cause interference w ith the spa's front acces s pan el if any repairs or maintenance of spa is required in the future. NPP1023 Tools required for assembly: (2) Coupler Extensions 25” 1. Phillips Screwdriver 2.
PAGE 3
SET-UP AND ASSEMBLY: • Place all parts in a cleared area and remove the packing materials from the spa shell; do not dispose of the packing materials until assembly is completed and the spa is in operation. • Assembly requires two people. • During assembly, make sure that all parts are oriented as shown in the drawings. Read each assembly step before you begin. • Tighten all parts as you assemble them, unless instructed to do otherwise.
PAGE 4
Step 4: • Attach the left and right Mounting Brackets to the appropriate sides of the spa, 3-5” above the ground* • Use (4) 1” Mounting Screws for the four outer holes. • Use (2) 4” Mounting Screws for the two inner holes. (Fig. 4-1) 4 x 1” Screws *NOTE: To prevent splitting of the spa cabinet, pre-drill holes with a ¼” drill bit. (Fig 4-1) 2 x 4” Screws Step 5: • With bracket mounted on spa, put Spacer Block on Pivot Arm Bolt (Fig.
PAGE 5
ATTENTION! SPA COVERS UP TO 72”: FOLLOW STEP 6-A SPA COVERS 73”-96”: FOLLOW STEP 6-B Step 6-A: FOR SPA COVERS UP TO 72” • Slide the LONG END of the Cover Support Arm into either side of the Coupler piece • Slide the SHORT END of the Cover Support Arm into the top of the Side Pivot Arm. Do the same on the other side. • The Cover Support Arm and the Coupler will now be laying on top of the spa cover along the fold. • THIS WILL FIT SPA COVERS UP TO 72” For larger spa covers see Step 6-B.
PAGE 6
Step 7: • Adjust the C oupler Piece and Support Arms so that the Coupler Piece is laying parallel, approximately ½” away from the fold in the spa cover. • Once you have the lifter fitted to the size of your spa, pre-drill the holes that connect all the arms together. • Using the 1” Self Tapping Screws, fasten Support Arms to the Coupler Pieces.