T1 QUICK START GUIDE
1 T1 Quick Start Guide: English MultiFunction Button (MFB) Indicator Light Microphones Charging Port 2 Charge Your T1 Your T1 has been given an initial partial charge to get started, but for best results charge it using the supplied USB cable and adaptor until the indicator light turns white. > Charge the T1 whenever it announces that the battery is Very Low. > A full charge takes about 3 hours. > During charging, the indicator light flashes red. > When the light goes white, the charge is complete.
Pair Your T1 1. Turn the T1 on by sliding the power switch on the back to the green on position. 4 Transfer Your Phonebook Power switch (on) 2. Put the T1 in your ear. 3. The first time you use the T1 it will go straight to pair mode and talk you through the pairing process. For subsequent pairings, make sure the T1 is not connected to any phones, then hold down the MFB. The T1 will announce that it is going into pairing mode. Tip: The pairing code is 0000 (four zeros).
5 Wearing the T1 6 Making Calls You can wear your T1 on either ear. For best results: > Position the hook and ear gel as shown here. Use your voice to make calls: LEFT EAR > Make sure the T1 is angled towards your mouth. Protective Skins Your T1 is supplied with optional rubber skins to protect against dust and moisture. RIGHT EAR 1. Click the MFB and wait for the T1 to ask you to Say A Command. 2. Say Phone Commands to activate the voice dial feature on your phone (if supported by your phone).
7 Taking Calls When the phone rings, you can answer the call with your voice: wait for the prompt to ask you if you want to take the call, and then say Answer or Ignore. If you don’t want to wait for the prompt, or you are in a noisy place: > Click the MFB once to accept the call. > Double click the MFB to reject the call. During a call, click the MFB to end the call.
9 Listening to Audio The T1 supports A2DP audio streaming: if your phone or Bluetooth device supports the A2DP profile then you can simply start playing music or any other audio (including directions from a GPS application on the phone) and it will automatically transfer to the T1. The audio will mute automatically if you make or receive a phone call, and resume when the call ends. 10 Multipoint Up to 2 phones can connect to the T1 at the same time. To pair a second phone: 1.
11 Advanced Button Functions 12 Advanced Button Functions > To hold an active call and switch to an incoming or held call, press Vol + for about 1 second. > During a call you can mute and unmute the T1 microphone by holding Vol + and Vol - together until the T1 beeps twice (about 1 second). > To end an active call and answer a new incoming call, press Vol - for about 1 second. > You can conference two active calls together by holding the MFB for 3 seconds (if your phone and network support this).
13 Reset your T1 14 Troubleshooting Tips If you are having problems with the T1, you can reset the T1 and your phone and start again: The following are some troubleshooting tips for using the T1 with specific phone models. 1. Disconnect the T1 from your phone by deleting the pairing from your phone’s Bluetooth menu. Phonebook Transfers 2. Turn your phone off and back on again to clear its memory. 3.
15 BlackBerry® 16 Android™ If you are using a BlackBerry smartphone you may see a message like this one during the phonebook transfer. On Android devices a message about the phonebook transfer may appear in the notifications area at the top of the screen. Accept connection request from BlueAnt T1? YES NO Don’t ask this again Select “Don’t ask this again” so that a tick appears in the box, and then choose “YES”.
17 Automatic Transfer Not Supported 18 Phonebook Transfer Not Supported Some phones do not support automatic phonebook transfers. If this is the case on your phone the T1 will announce that it cannot transfer the contacts automatically: Some phones do not support phonebook transfers at all. 1. Go to your phonebook and select the contacts you want to send to the T1.
19 Voice Dialing 20 Help and Support Use the command Phone Commands to activate your phone’s voice dial feature. Your phone must support “voice dialing over Bluetooth”. This guide is just to get you started with the T1. If you are having trouble getting the T1 to work, please visit www.blueantwireless.com for online help, support, and troubleshooting tips. This feature is supported by the iPhone 3GS (iOS 3.1+) and iPhone 4, most BlackBerry smartphones, and most Android devices running Android 2.
NEED MORE HELP? “HOW-TO VIDEOS FOR YOUR BLUEANT DEVICE” www.blueantwireless.
