Installation Guide

This Refrigerator Filter Cartridge is Tested
and Certified by NSF International against
NSF/ANSI Standard 42 for materials and
structural integrity requirements.
NSF
R
Certified by IAPMO R&T against NSF/ANSI
Standard 42 for materials safety, structural
integrity and aesthetic chlorine reduction
when used in the BF-LGLT600P-S
This system has been tested according to NSF/ANSI 42 for the reduction of the
substance listed below. The concentration of the indicated substances in water
entering the system was reduced to a concentration less than or equal to the
permissible limit for water leaving the system as specified in NSF/ANSI standard 42.
Performance Data Sheet
Replacement Filter - BF-LGLT600P-S
Contaminant
Reduction*
Average
Influent
NSF Specified
Challenge
Concentration
Avg.%
Reduction
Average
Product Water
Concentration
Max Permissible
Product Water
Concentration
NSF Reduction
Requirements
Chlorine
Taste and Odor
2.1 mg/L
2.0 mg/L ± 10%
97.40%
0.06 mg/L
N/A
≥ 50%
Tested at a flow rate of 0.5 gpm to a capacity of 300 gallons for the reduction of Chlorine, Taste and Odor.
For Residential Use Only
To reduce the risk associated with ingestion of contaminants:
To reduce the risk associated with property damage due to water leakage:
Installing the Filter Cartridge
^The replacement component BF-LGLT600P is ^compatible with the following absolute or alternate filter part numbers:
Service Flow
LT600P 5231JA2005A 5231JA2005A-S 5231JA2006 5231JA2006A 5231JA2006A-S
5231JA2006B 5231JA2006B-S 5231JA2006E 5231JA2006F 5231JA2006F-S 5231JA2006H
469990 WSL-2 SGF-LB60 WF300 RWF1000A
Water Supply
Water Pressure
Water Temperature
0.5 gpm/(1.9 lpm)
Potable Water
30 -100 psi (207 – 689 kPa)
34 F - 100 F (1 C - 38 C)
°
°
°
°
For optimum performance, it’s recommended you change your filter every 6 months(Depends on water quality and level of contaminants)
A. On models without a replacement indicator light, apply the 6 month reminder sticker to the new cartridge and mark your calendar.
B. Remove old filter cartridge by grasping and turning to the left about 1/4 turn.
C. Align the indicator line so that it can be inserted into the filter cover.
D. Turn the cartridge 1/4 turn to the right to lock it into place.
E. Run water from the dispenser for 6-8 minutes (about 3-4 gallons) to clear the system and prevent sputtering.
F. On models with a replacement indicator light, press and hold the RESET WATER FILTER PAD on the dispenser.
*All trademarks remain the property of their respective holder(s) and are used for compatibility information only.
^Claimsofcompatibilityverifiedthroughmanufacturertesting.
A.Read and follow Use Instructions before installation and use of this system.
B.Installation and use MUST comply with all state and local plumbing codes.
C.Protect from freezing, remove filter cartridge when temperatures are expected to drop below 34℉(1℃)
D.Do not install systems in areas where ambient temperatures may go above 110℉ or below 40℉
E.Do not install on hot water supply lines. The maximum operating water temperature of this filter system is 100℉(38℃)
F. Do not install if water pressure exceeds 100psi. If your water pressure exceeds 80psi (552kPa), you must install
a pressure limiting valve. Contact a plumbing professional if you are uncertain how to check your water pressure.
G.Do not install where water hammer conditions may occur. If water hammer conditions exist you must install a water hammer arrester.
Contact a plumbing professional if you are uncertain how to check for this condition.
H.Where a backflow prevention device is installed on a water system, a device for controlling pressure due to thermal expansion
must be installed.
I. The disposable filter cartridge MUST be replaced every 6 months, at the rated capacity or sooner
if a noticeable reduction in flow rate occurs.
Do not use with water that is microbiologically unsafe or of unknown quality without adequate
disinfection before or after the system.
COMPONENT