Single Zone Energy Star IDU Owners Manual

Press this button, the quiet status is under the auto
quiet mode (display " " and "Auto" signal) and quiet
mode (display " " signal) and quiet off (there is no
signal of " " displayed), after powered on, the quiet
off is defaulted.
Under the quiet mode (Display " " signal).
9
button
Press this button once, to turn on the I FEEL func-
tion, then the figure of "I FEEL" will be displayed,
after every press of other function button, every
200ms to send I FEEL once, after this function
started, the remote controller will send temperature
to the main unit in every 10 minutes. When repress
this button, this function will be turned off. When I
FEEL function is turned on, the remote controller
should be put within the area where indoor unit can
receive the signal sent by the remote controller.
I FEEL
button
Press this button at unit on or off status, light on and
light off can be set up. After powered on, light on is
defaulted.
LIGHT
button
Press " WiFi " button to turn on WiFi function, "WiFi "
icon will be displayed on the remote controller;
Hold " WiFi " button for 5s to turn off WiFi function
and " WiFi " icon will disappear.
Under off status, press "MODE" and " WiFi " buttons
simultaneously for 1s, WiFi module will restore
factory settings.
WiFi
button
QUIET
Outdoor temperature display is not available for some
models. At that time, indoor unit receives " "
signal, while it displays indoor set temperature.
●
NOTE
The quiet function is only available for some models.
●
NOTE
This function is only available for some models.
●
NOTE
●
●
Press this button, can select Sleep 1 ( ), Sleep
2 ( ), Sleep 3 ( ) and cancel the Sleep,
circulate between these, after electrified, Sleep
cancel is defaulted.
Sleep 1 is sleep mode 1, in cool, dehumidify modes:
sleep status after run for one hour, the main unit
setting temperature will increase 1°C, 2 hours, set-
ting temperature increased 2°C, the unit will run at
this setting temperature; In heat mode: sleep
status after run for one hour, the setting tem-
perature will decrease 1°C, 2 hours, setting tem-
perature will decrease 2°C, then the unit will run at
this setting temperature.
button
SLEEP
●
Sleep 2 is sleep mode 2, that is air conditioner
will run according to the presetting a group of sleep
temperature curve.
In cool mode:
(1) When setting the initial temperature 16°C -23°C,
after turned on sleep function, the temperature
will be increased 1°C in every hour, after 3°C the
temperature will be maintained, after 7 hours, the
temperature will be decreased 1°C, after that the
unit will keep on running under this temperature;
(2) When setting the initial temperature 24°C-27°C,
after turned on sleep function, the temperature
will be increased 1°C in every hour, after 2°C the
temperature will be maintained, after 7 hours,
the temperature will be decreased 1°C, after that
the unit will keep on running under this temperature;
(3) When setting the initial temperature 28°C-29°C,
after turned on sleep function, the temperature
will be increased 1°C in every hour, after 1°C the
temperature will be maintained, after 7 hours,
the temperature will be decreased 1°C, after that
the unit will keep on running under this tempera-
ture;
button
Press this button to turn on or turn off the health
and scavenging functions in operation status.
Press this button for the first time to start scaveng-
ing function; LCD displays " ". Press the button
for the second time to start health and scavenging
functions simultaneously; LCD displays " " and
" ". Press this button for the third time to quit
health and scavenging functions simultaneously. Press
the button for the fourth time to start health function;
LCD display " ". Press this button again to
repeat the operation above.
This function is applicable to partial of models.
●
NOTE