Single Zone Energy Star IDU Owners Manual

10
In the above presetting or enquiry procedure, if
continuously within 10s, there is no button pressed,
the sleep curve setting status will be automatically
quit and resume to display the original displaying. In
the presetting or enquiry procedure, press "ON/OFF"
button, "Mode" button or "Sleep" button, the sleep
curve setting or enquiry status will quit similarly.
●
NOTE
When AUTO RUN mode is selected, the setting
temperature will not be displayed on the LCD, the
unit will be in accordance with the room temp.
automatically to select the suitable running method
and to make ambient comfortable.
About AUTO RUN
If start this function, the unit will run at super-high
fan speed to cool or heat quickly so that the ambi-
ent temperature approachs the preset temperature
as soon as possible.
About turbo function
Press + and - buttons simultaneously to lock or
unlock the keyboard. If the remote controller is
locked, the icon will be displayed on it, in which
case, press any button, the mark will flicker for
three times. If the keyboard is unlocked, the mark
will disappear.
About Child lock
Introduction for special function
●
according to the initial curve setting value of origin-
al factory);
(2) Adjust "+" and "-" button, could change the
corresponding setting temperature, after adjusted,
press "Turbo" button for confirmation;
(3) At this time, 1 hour will be automatically in-
creased at the timer position on the remote con-
troller, (that are "2 hours" or "3 hours" or "8 hours"),
the place of setting temperature "88" will display
the corresponding temperature of last setting sleep
curve and blink;
(4) Repeat the above step (2)~(3) operation, until
8hours temperature setting finished, sleep curve
setting finished, at this time, the remote controller
will resume the original timer display; temperature
display will resume to original setting tempera-
ture.
Sleep3 - the sleep curve setting under sleep mode
by DIY could be inquired:
The user could accord to sleep curve setting method
to inquire the presetting sleep curve, enter into user
individuation sleep setting status, but do not
change the temperature, press "Turbo" button di-
rectly for confirmation.
●
(4) When setting the initial temperature 30°C, under
this temperature setting, after 7hours, the tem-
perature will be decreased 1°C, after that the unit
will keep on running under this temperature;
In heat mode:
(1) Under the initial presetting temperature 16°C,
it will run under this setting temperature all along.
(2) Under the initial presetting temperature 17°C
-20°C, after Sleep function started up, the tempera-
ture will decrease 1°C in every hour, after 1°C de-
creased, this temperature will be maintained.
(3) Under the initial presetting temperature 21°C
-27°C, after Sleep function started up, the tempera-
ture will decrease 1°C in every hour, after 2°C de-
creased, this temperature will be maintained.
(4) Under the initial presetting temperature 28°C
-30°C, after Sleep function started up, the tempera-
ture will decrease 1°C in every hour, after 3°C de-
creased, this temperature will be maintained.
Sleep 3 - the sleep curve setting under sleep mode
by DIY:
(1) Under Sleep 3 mode, press "Turbo" button for
a long time, remote controller enters into user
individuation sleep setting status, at this time,
the time of remote controller will display "1 hour",
the setting temperature "88" will display the
corresponding temperature of last setting sleep
curve and blink (The first entering will display
1. Press swing up and down button continuously
more than 2s, the main unit will swing back and forth
from up to down , and then loosen the button, the unit
will stop swing and present position of guide louver
will be kept immediately.
2. Under swing up and down mode, when the status
is switched from off to , if press this button again
2s later, status will switch to off status directly; If
press this button again within 2s, the change of
swing status will also depend on the circulation
sequence stated above.
About swing up and down