Models: BMKH24M-ND3G BMKH30M-ND3G BMKH36M-ND3G
In line with the company’s policy of continual product improvement, the aesthetic and dimensional characteristics, technical data and accessories of this appliance may be changed without notice.
Explanation of Symbols DANGER Indicates a hazardous situation that, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation that, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury. NOTICE Indicates important but not hazard-related information, used to indicate risk of property damage.
THE INSTRUCTIONS BEFORE USE GENERAL INFORMATION WARNING ★ When having a burning smell or ★ The power supply must adopt the smoke,please turn off the power supply and contact with the service center. special circuit that with air switch protection and assure it has enough capacity.The unit will be turned on or off according to your requirement automatically,please do not turn on or turn off the unit frequently,otherwise disadvantage effect may be caused to the unit.
NAME OF PARTS BMKH24M-ND3G GENERAL INFORMATION BMKH30M-ND3G WARNING Be sure to cut off the power supply before cleaning the air conditioner; otherwise electric shock might happen. Wetting of air conditioner may cause the risk of electric shock. Make sure not to wash your air conditioner in any case. Volatile liquids such as thinner or gasoline will cause damage to the appearance of air conditioner. (Only use soft dry cloth moist cloth clean the air conditioner cabinet).
TECHNICAL DATA GENERAL INFORMATION BMKH24M-NDG3G MODE Electrical data Electricity supply Fuse or air switch Minimum power cord section 208/230V,60HZ 30 3.3 A mm 2 L 920 mm P 380 mm H 790 mm Size and clearance L P H TECHNICAL DATA GENERAL INFORMATION BMKH30M-NDG3G MODE Electrical data Electricity supply Fuse or air switch Minimum power cord section 208/230V,60HZ 30 3.
ELECTRICAL CONNECTIONS BMKH24M-NDG3 INSTALLER BMKH30M-NDG3 BMKH36M-NDG3 1. Remove the handle at the right side plate of the outdoor unit (one screw). 2. Remove the cable clamp, connect the power con -nection cable with the terminal at the row of conn -ection and fix the connection. The fitting line distr -ibuting must be consistent with the indoor unit. terminal of line bank. Wiring should meet that of indoor unit. 3. Fix power connection wire by wire clamp. 4. Ensure wire has been fixed well. 5.
ELECTRICAL CONNECTIONS INSTALLER BMKH30M-NDG3 OUTDOOR UNIT XT L1 L2 N( 1) 2 3 PO WER N (1 ) 2 3 N ( 1) 2 3 PE PE N(1 ) 2 L1 L2 3 N(1 ) 2 PE XT4 XT3 X T2 X T1 N( 1) 2 3 PE PE N ( 1) 2 INDO OR UNIT A INDOOR UNIT B 3 3 N(1 ) 2 3 INDO OR UNIT C INDO OR UNIT D BMKH36M-ND3G OU TDOOR UNIT XT L1 L2 N(1) 2 3 PE L1 L2 POWER N(1) 2 N(1) 2 3 3 INDOOR UNIT A N(1) 2 3 INDOOR UNIT B N(1) 2 N(1) 2 3 N(1) 2 PE PE XT5 XT4 XT3 XT2 XT1 3 3 6 N(1) 2 3 PE PE INDO
INSTALLING THE OUTDOOR UNIT INSTALLER Location Caution: Installation Must be Performed in Accordance with the NEC/CEC by Authorized Personnel Only. Install the drain fitting and the drain hose (for model with heat pump only) Condensation is produced and flows from the outdoor unit when the appliance is operating in the heating mode. In order not to disturb neighbours and to respect the environment,install a drain fitting and a drain hose to channel the condensate water.
MAINTENANCE INSTALLER Use suitable instruments for the refrigerant R410A. ● Do not use any other refrigerant than R410A. Do not use mineral oils to clean the unit. INSTALLATION DIMENSION DIAGRAM INSTALLER The installation must be done by trained and qualified service personnel with reliability according to this manual. Contact service center before installation to avoid the malfunction due to unprofessional installation.
CHECK AFTER INSTALLATION INSTALLER Check Items Problems Owing to Improper Installation Is the installation reliable? The unit may drop, vibrate or make noises Has the gas leakage been checked? May cause unsatisfactory cooling (heating) effect Is the thermal insulation of the unit sufficient? May cause condensation and water dropping Is the drainage smooth? May cause condensation and water dropping Does the power supply voltage accord with the rated voltage specified on the nameplate? The unit m