LM Wall Mount User Manual
Child lock function
I FEEL Function
●
●
●
signal sender
battery
reinstall
Replacement of batteries in
remote controller
remove
Cover of battery box
Temperature display switchover function
1.
2.
Under OFF status, press "▼" and "MODE" buttons
simultaneously to switch temperature display
between
℃ and ℉.
Press "▲" and "▼" simultaneously to turn on or
turn off child lock function. W -c nuf kcol dlihc neh
tion is on, " " icon is displayed on remote control
-
ler. If you operate the remote controller, the " "
icon will blink three times without sending signal to
the unit.
Reinstall the cover of battery box.
3.
●
●
●
●
●
10
Press the back side of remo te controll er
marked with " ", as shown in the fig, and then
push out the cover of battery box along the
arrow direction.
Replace two 7# (AAA 1.5V) dry batteries, and
make sure the position of "+" polar and "-" polar
are correct.
NOTICE
●
NOTE
●
8℃. Press "TEMP" and "CLOCK" buttons simulta-
neously again to exit 8℃ heating function.
Under 8℃ heating function, fan speed is defaulted at
auto speed and it can
't be adjusted.
Under 8℃ heating function, set temperature can
't be
adjusted. Press "TURBO" button and the remote
controller won
't send signal.
Sleep function and 8℃ heating function can
't operate
at the same time. If 8℃ heating function has been set
under heat mode, press sleep button will cancel 8℃
heating function. If sleep function has been set under
heat mode, start up the 8℃ heating function will
cancel sleep function.
Under ℉ temperature display, the remote controller
will display 46℉ heating.
During operation, point the remote control signal
sender at the receiving window on indoor unit.
The distance between signal sender and receiving
window should be no more than 8m, and there
should be no obstacles between them.
Signal may be interfered easily in the room where
there is fluorescent lamp or wireless telephone;
remote controller should be close to indoor unit
during operation.
Replace new batteries of the same model when
replacement is required.
When you don
't use remote controller for a long time,
please take out the batteries.
If the display on remote controller is fuzzy or there
's
no display, please replace batteries.
8℃ heating function
Under heat mode, press "TEMP" and "CLOCK"
buttons simultaneously to start up or turn off 8℃
heating function. When this function is started up,
" " and "8℃" will be shown on remote controller,
and the air conditioner keep the heating status at
Press "▲" and "MODE" buttons simultaneously to
start I FEEL function and " " will be displayed on
the remote controller. After this function is set, the
remote controller will send the detected ambient
temperature to the controller and
the unit will auto-
matically adjust the indoor temperature according
to the detected temperature. Press this two
buttons simultaneously again to close I FEEL func-
tion and " " will disappear.
Pleas
e put the remote controller near user when
this function is set. Do not put the remote control-
ler near the object of high temperature or low tem-
perature in order to avoid detecting inaccurate
ambient temperature. When I FEEL function is
turned on, the remote controller should be put
within the area where indoor unit can receive the
signal sent by the remote controller.
●
●
●
NOTE
Und
e
r
ener
g
y
-savi
ng function, fan
spe
e
d
is
d
efau
lt
e
d
at auto speed and it can
'
t be adjusted.
Und
e
r
ene
r
g
y
-sa
v
ing function, set t
empe
r
atu
r
e c
an
'
t
b
e
adj
uste
d
.
P
re
ss
"
T
U
R
B
O
"
b
u
tt
on an
d t
he
re
mote
controller won
'
t send signal.
S
le
ep function an
d
ener
g
y
-sa
v
ing functio
n
can
'
t ope
r
-
ate at the sam
e
time
. I
f
ener
g
y
-sa
v
ing functio
n
h
as
be
en set
und
e
r
cool
mo
d
e,
pr
ess s
le
ep
b
u
tt
on
wi
ll
cancel
ene
r
g
y
-sa
v
ing function
. I
f s
le
ep function has
be
en
s
et
unde
r
cool
mo
d
e
,
sta
r
t
up
t
he
ene
r
g
y
-sa
v
ing
function will cancel sleep function.